General Identification; Specifications - Talon AB3202 User Manual

GENERAL IDENTIFICATION

20
19
14
5
15
2
16
13
1. THROTTLE TRIGGER 9. AIR CLEANER COVER
2. THROTTLE LOCK 10. 3-POSITION CHOKE LEVER
3. IGNITION SWITCH 11. FUEL TANK
4. THROTTLE CONTROL ARM 12. FUEL CAP
5. STARTER HANDLE 13. SPARK PLUG LEAD / SPARK
6. MUFFLER COVER PLUG
7. SPARK ARRESTER SCREEN 14. TOP ASSIST HANDLE
8. CARBURETOR / PRIMER BULB 15. BRIDGE

SPECIFICATIONS

Engine Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air-cooled, 2 Cycle
Engine displacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 cc
Engine Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7,000
Idle Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3,000-3,500 rpm
Air Velocity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 288 km/h
Air Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 cu.m/min.
Fuel Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 710 ml
Dry Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.9 kg
Sound Power Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 dB(A)
Sound Pressure Level at ear . . . . . . . . . . . . . . . . . . . . . . . 91 dB(A)
Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11.2 m/s
16
17
3
1
4
17
21
18
16. VENTED BACK PAD
17. PISTOL GRIP ASSIST HANDLE
18. FLEX TUBE
19. EXTENSION TUBES (2)
20. CONCENTRATOR NOZZLE
21. HARNESS
22. STARTING INSTRUCTIONS
±
500 rpm
2
4
AU
ASSEMBLY INSTRUCTIONS
• ATTACH FLEX TUBE
1. Align the flex tube tab (A) with notch (B) in the hous-
22
ing (Fig. 1A).
2. Push tube into housing up to ridge (C) (Fig. 1B).
9
3. Twist tube counterclockwise to lock into place (Fig.
10
1C). And tighten the screw D. (Fig. 1D).
6
7
8
A
11
Fig. 1A
12
Fig. 1C
• ATTACH EXTENSION TUBES (2) AND
CONCENTRATOR NOZZLE
21
1. Align grooves (A) on extension tube with notches (B)
in flex tube (Fig. 2A).
2. Push in up to ridge on extension tube (C) (Fig. 2B).
3. Twist tube clockwise until it clicks into position and
locks (Fig. 2B)
4. 2nd extension tube (D): repeat steps 1 through 3
above (Fig. 2C).
5. Concentrator nozzle (E): repeat steps 1 through 3
above (Fig. 2C).
B
Fig. 2A
•
1.
2.
3.
NOTE: There are three buckles for this harness. ( Fig.
C 3B) (A.B.C.).Buckle C is the main buckle for securing the
harness.
B
Fig. 1B
D
Fig. 1D
C
A
Fig. 2B
D E
Fig. 2C
5
AU
ADJUST BACK PACK AND HARNESS
Place blower on your back by slipping arms through
the shoulder straps as if you were putting on a jacket
(Fig. 3A).
Adjust shoulder and chest straps so that the back
pack feels comfortable on your back (Fig. 3B).
Once adjustments have been made, remove the
blower from your back and place on level ground.
C
B
A
Fig. 3A Fig. 3B
Fig. 3C