Fortinet FortiGate 50B-LENC Quick Start Manual

LED State
Green
Power
Off
Green
Status
Off
Green
Link / Activity Flashing
Green
Off
10/100 Green
Visit these links for more information and documentation for your Fortinet product.
• Technical Documentation - http://docs.forticare.com
• Fortinet Knowledge Center - http://kc.forticare.com
• Fortinet Technical Support - http://support.fortinet.com
Package Contents
Connector
Internal
WAN1 and
WAN 2
CONSOLE
USB
Power LED
POWER
50B-LENC
Status LED
DC+12V
Ground
Power
Connection
RJ-45 Serial
Connection
Connecting
Connect the following to the FortiGate unit. Ensure the FortiGate unit is placed on a stable
surface.
• Insert a network cable to WAN1. Insert the other end to the router connected to the
Internet, or to the modem.
• Connect a network cable to the Internal port 1, 2 and 3.
Insert the other end to a computer or switch.
• Connect the AC Power Cable to the Power Supply.
• Connect the Power Cord to a surge protected power bar or power supply.
Configuration Tools
Web-based manager
The FortiGate web-based manager is an easy to use management tool.
Use it to configure the administrator password, the interface and default gateway addresses,
and the DNS server addresses.
Requirements:
• An Ethernet connection between the FortiGate unit and management computer.
• A web browser such as FireFox or Internet Explorer on the management computer.
Description
The FortiGate unit is on.
The FortiGate unit is off.
On during start up or reboot.
Normal operation.
The correct cable is in use and the connected equip-
ment has power.
Network activity at this interface.
No link established.
The interface is connected at 100 Mbps.
Type Speed Protocol Description
RJ-45 10/100 Base-T Ethernet
RJ-45 10/100 Base-T Ethernet
RJ-45 9600 bps RS-232
serial
USB USB
Front
INTERNAL
WAN1 WAN2
LINK / ACT
STATUS
10/100
1 2 3
WAN 1,2 Internal
Interface Interface
Back
3 2 1 WAN2 WAN1
USB
USB
WAN2
Internal Interface,
switch connectors
1,2,3
QuickStart Guide
© Copyright 2008 Fortinet Incorporated. All rights reserved.
Products mentioned in this document are trademarks or registered trademarks
of their respective holders.
Regulatory Compliance
FCC Class B Part 15 CSA/CUS
14 October 2008
3-port switch connection to up to three devices or the internal network.
Redundant connections to the Internet.
Optional connection to the management computer.
Provides access to the command line interface (CLI).
Optional connection for FortiUSB key for firmware backup and installation.
Straight-through
Ethernet cable
Power Cable
WAN1
Power cable
connects to power supply
DC+12V
Ground
Command Line Interface (CLI)
The CLI is a full-featured management tool. Use it to configure the administrator password,
the interface addresses, the default gateway address, and the DNS server addresses. To
configure advanced settings, see the Tools and Documentation CD included with the
FortiGate unit.
Requirements:
• The RJ-45 to DB9 serial connection between the FortiGate unit and management com-
puter.
• A terminal emulation application (HyperTerminal for Windows) on the management
computer.
WAN1 WAN2
POWER STATUS
50B-LENC
RJ-45 to
Tools and Documenation
DB-9 Serial Cable
Power Supply
RJ-45 to DB-9 serial cable
connects to management
computer
3
USB
Ethernet cables connect
to computers on the internal
network
FortiGate-50B-LENC
INTERNAL
LINK / ACT
10/100
1 2 3
01-30006-0477-20081014
QuickStart Guide
FortiGate-30B
INTERNAL
WAN1 WAN2
POWER STATUS
1 2 3
50B-LENC
Copyright 2008 Fortinet Incorporated. All rights reserved.
Trademarks
Products mentioned in this document are trademarks.
Welcome | Bienvenue | Willkommen | 歓迎 | Bienvenido | Benvenuto
2 1 WAN2 WAN1
Ethernet cables connect
to the Internet or router