Related Manuals for Miele DA 426-4
Summary of Contents for Miele DA 426-4
- Page 1 Operating and installation instructions Cooker hood DA 426-4 To avoid the risk of accidents GiWOZ or damage to this appliance it is to read these instructions before it is installed and used for the first time. M.-Nr. 06 784 080...
- Page 2 ......... . 3 .
- Page 3 Electrical and electronic appliances often contain materials which, if The transport and protective packing handled or disposed of incorrectly, has been selected from materials which could be potentially hazardous to are environmentally friendly for human health and to the environment. disposal, and can normally be They are, however, essential for the recycled.
- Page 4 This appliance complies with all Before connecting the appliance to relevant legal safety requirements. the mains supply, make sure that Inappropriate use can, however, the connection details given on the lead to personal injury and damage data plate correspond with the on-site to property.
- Page 5 The appliance is only completely When using the cooker hood over isolated from the electricity supply a gas hob, ensure that any burners when: in use are always covered by a pan. The burner should be switched off – it is switched off at the wall socket before taking a pan off the hob, even and the plug withdrawn, for brief periods.
- Page 6 These can be obtained from the Miele and remain hot for some time after Spare Parts department or from switching off. To safeguard against builders' merchants.
- Page 7 In order to ensure safe operation, and to prevent gases given off by the heating appliances from being drawn back into the room when the extractor and the heater are in operation simultaneously, an underpressure in the room of 0.04 mbar (4 pa) is the maximum permissible.
- Page 8 The Miele DSM 400 control module offers the possibility of combining other components with the cooker hood (see "Operation with Control module DSM 400").
- Page 9 The cooker hood works with (available as an optional extra with a conversion kit and charcoal filter: see "Technical Data") The air is drawn in and cleaned by the grease filters and directed outside. If the on-site ventilation system does not have a , the The air is drawn in and cleaned first by...
- Page 11 (only for recirculation mode) (special accessory for recirculation mode)
- Page 12 If the cooker hood has been connected to a window contact switch via the Miele DSM 400 control The hob lighting can be switched on module, then the fan cannot be and off independently of the fan.
- Page 13 ^ Press the control to activate the automatic switch-off. The indicator lamps for fan power You can set the Intensive setting so that levels I and IV will now light up it only runs for 10 minutes before constantly. reverting automatically to level III. Press the control to deactivate the ^ To set this option, both the fan and...
- Page 14 (This infomation does not apply to the be washed 300 times. controls). Stainless steel surfaces can be cleaned using the Miele E-Cloth, or with a proprietary non-abrasive cleaning agent designed specifically for use on stainless steel. The surfaces and controls are...
- Page 15 (special order finish) It is very difficult to clean this type of surface without causing minor marks to the surface material. This can become particularly noticeable with darker colours and if there is halogen lighting in the kitchen. ^ To take out the grease filters, release the locking clip on the filter, lower the The controls may suffer filter 45°, unhook it at the back and...
- Page 16 (with a pH value higher than 7). New filters can be purchased from Depending on the cleaning agent your Miele dealer or from the Miele used, cleaning the filters in a Spare Parts Department. dishwasher can cause permanent See back cover for contact details, discolouration to the surface.
- Page 17 Before any cleaning or maintenance work, disconnect the cooker hood from the mains supply. Ensure that: – it is switched off at the isolator, or – it is switched off at the wall socket and the plug removed, or – the fuse is withdrawn from the fused spur connection unit, or –...
- Page 18 In the event of a fault which you cannot correct yourself, or if the appliance is under guarantee, please contact: – Your Miele Dealer – The Miele Service Department (see back cover for address). When contacting your Dealer or the Service Department, please quote the model and serial number of your appliance.
- Page 19 When planning the installation height of your cooker hood, the safety distances between the top of a cooker or hob and the bottom of the cooker hood are as follows, unless a greater distance is specified by the manufacturer of your cooking appliance: –...
- Page 21 for use when fitting the tower. for securing the exhaust ducting. for securing the appliance. for exhaust ducting C 125 mm . for fitting into the exhaust connection on the motor unit (for extraction for securing the tower. mode only) for securing the cooker hood to the wall.
- Page 22 Before installation, it is important to Should the appliance ever need to be read the information given on the dismantled, follow the installation following pages as well as the instructions in reverse order as "Appliance dimensions" and the described on the installation sheet. "Warning and Safety instructions"...
- Page 23 – Where ducting is horizontal, it must Important: To avoid the danger of be laid to slope away at at least 1 cm toxic fumes, please observe the per metre. Warning and Safety instructions. This is to ensure that condensate This is especially crucial when using cannot drain back into the cooker the cooker hood at the same time as...
- Page 24 If the exhaust ducting is to run through rooms, ceiling space etc. where there may be great variations in temperature between the different areas, the problem of condensation will need to be addressed. The exhaust ducting will need to be suitably insulated. (optional extra) To achieve even further reductions in noise levels, a special silencer can be...
- Page 25 additional means of disconnection must All electrical work should be be provided for all poles. undertaken by a suitably qualified For extra safety it is advisable to install and competent person in strict a residual current device (RCD) with a accordance with current national trip current of 30 mA.
- Page 26 The Miele DSM 400 Control module can If the control module is disconnected be used to combine the cooker hood in order to operate the cooker hood with other components. without the window contact switch It enables the following: (e.g. after moving house) the cooker hood electronics must be reset by a Miele service technician.
- Page 27 The control module can be used to switch on the cooker hood lighting and also to dim it, depending on model, via a light switch in the house. The tower needs to be removed before the control module can be fitted to the fan unit.
- Page 28 Total connected load ..160 W - Fan motor ....120 W Extraction power according to - Hob lighting .
- Page 32 Alteration rights reserved / 1006 M.-Nr. 06 784 080 / 01 en - GB...