IMPORTANT SAFETY INSTRUCTIONS WARNING: When using electrical products, basic cautions should always be followed, including the following: 1. Read these instructions. 2. Keep these instructions safe. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6.
Page 3
INSTRUCTIONS IMPORTANTES DE SECURITE - FRANÇAIS ATTENTION: L’utilisation de tout appareil électrique doit être soumise aux precautions d’usage incluant: 1. Lire ces instructions 2. Gardez ce manuel pour de futures références. 3. Prétez attention aux messages de précautions de ce manuel. 4.
Page 4
WICHTIGE SICHERHEITSHINWEISE - DEUSCH ACHTUNG: Beim Einsatz von Elektrogeräten müssen u.a. grundlegende Vorsichtsmaßnahmen befolgt werden: 1. Lesen Sie sich diese Anweisungen durch. 2. Bewahren Sie diese Anweisungen auf. 3. Beachten Sie alle Warnungen. 4. Befolgen Sie alle Anweisungen. 5. Setzen Sie dieses Gerät nicht in der Nähe von Wasser ein. 6.
Page 5
INSTRUCCIONES IMPORTANTES PARA SU SEGURIDAD - ESPAÑOL CUIDADO: Cuando use productos electrónicos, debe tomar precauciones básicas, incluyendo las siguientes: 1. Lea estas instrucciones. 2. Guarde estas instrucciones. 3. Haga caso de todos los consejos. 4. Siga todas las instrucciones. 5. No usar este aparato cerca del agua. 6.
Page 6
PRECAUCION: Para disminuir el risego de carrientazo, no abra la cubierta. No hay piezas adentro que el pueda reparar. Your Laney amplifier has undergone a thorough two stage, pre- Deje todo mantenimiento a los tecnicos calificadod. delivery inspection, involving actual play testing.
SPECIFICATIONS LV300 LV300TWIN LV300H Supply Voltage on all models:- Factory ~100V, ~120V, ~220V, ~230V, ~240V 50/60Hz Preset Mains Fuse: ~100V>~120V T5A L T5A L T5A L ~220V,~230V,~240V T2A L T2A L T2A L 300W Power Consumption 300W 300W Output Power Rating...
ECC83 DRIVE2 TUBE STAGE POWER EXT. ON MUTE LOUDSPEAKER FOOTSWITCH INTERNAL LOUDSPEAKERS In the interest of continued development, Laney reserves the right to amend product specification EXT. without prior notification. LOUDSPEAKER LV300TWIN 300H FX SEND FX RETURN CLEAN INPUT BRIGHT...
Page 10
The LV300 and LV300Twin are 120W open back three channel guitar combos. They feature a true tube-loaded drive stage; separate three band eq for the clean and drive channels (Drive 1 + 2 share); clean channel bright switch; drive channel ‘V’ preshape and an overall ‘VTS’...
Page 11
We hope you enjoy using your new LV300, whichever model you choose, as much as we enjoyed designing and making it. It should give you years of trouble-free service, however please take time to read this manual, as it will allow you to get the best from your model.
Page 13
Switch in to activate the drive1 channel. When active, control the amount of distortion with and the overall volume with . The centre of the switch will be lit when active. Sets the level of gain on the drive1 channel. For optimum results the gain control should be used in conjunction with the volume control .
Page 14
Line level FX Loop Return to connect back from an external effects controller. Line level FX Loop Send to connect to an external effects controller. Connect a dedicated Laney LV3Way footswitch here (included) to allow remote switching of the reverb and channels. Drive channel must be enabled (with )
Page 15
GENERAL NOTES Amplifier connection: In order to avoid damage, it is advisable to establish and follow a pattern for turning on and off your equipment. With all system parts connected, turn on source equipment, tape decks, cd players, mixers, effects processors etc. BEFORE turning on your guitar amplifier. Many products have large transient surges at turn on and off which can cause damage to your speakers.
Page 16
~220V/~230V MAXIMUM POWER CONSUMPTION 300 WATTS 50/60Hz www.laney.co.uk L Z B 1 2 3 4 The total impedance of the cabinet/s must not be less than 8 Ohms. Connecting cabinets that have a lower impedance than 4 Ohms will result in the amplifier overheating and may cause permanent damage.
Page 17
~115V ~220V/~230V L Z B 1 2 3 4 www.laney.co.uk The total impedance of the cabinet/s must not be less than 4 Ohms. Connecting cabinets that have a lower impedance than 4 Ohms will result in the amplifier overheating and may cause permanent damage.
Page 18
DRIVE 2 DRIVE EQUALISATION REVERB BRIGHT TUBE FUSION POWER INPUT VOLUME CLEAN BASS MIDDLE TREBLE DRIVE 1 GAIN MASTER DRIVE 2 GAIN MASTER BASS MIDDLE TREBLE CLEAN DRIVE METAL SETTINGS QUICK START SETTINGS - (LV300 Shown, settings will suit all models)