Setting Up - La Crosse Technology WS-9611U-IT Instruction Manual


DST ON/OFF (daylight saving time)

Time zone option ±12 hours

Year, month, date, weekday calendar display

Crescendo alarm with snooze function

Advanced Weather Forecast Icons with 15 combinations of weather icons

Weather tendency indicator

Temperature display with MIN/MAX records and time and date of reception

Indoor and outdoor temperature display in ºF or ºC

Indoor humidity data display as RH% with MIN/MAX records

Can receive up to 3 remote temperature/humidity sensors

Sun rise and sun set for 99 selected US and Canada cities

Moon phase

LCD contrast selectable

LED backlight

Low battery indicator

Wall hanging or table standing
3. After inserting the batteries, the Weather Station will start receiving data from the
transmitter. The outdoor temperature and the signal reception icon should then be
displayed on the Weather Station. If this does not happen after 3 minutes, the
batteries will need to be removed from both units and reset from step 1.
4. In order to ensure sufficient 915 MHz transmission however, this should under
good conditions be a distance no more than 330 feet (100 meters) between the
final position of the Weather Station and the transmitter (see notes on
"Positioning" and "915 MHz Reception").
5.
Once the remote temperature has been received and displayed on the Weather
Station, the WWVB time (radio controlled time) code reception is automatically
started. This takes typically between 3-5 minutes in good conditions. If after 10
minutes, the WWVB time has not been received, press the SET key to manually
enter a time initially.
When more than one transmitter is used
1. User shall remove all the batteries from the Weather Station and transmitters and
wait for 60 seconds if setting has been done with one transmitter before.
2. Insert the batteries to the first transmitter.
3. Within 25 seconds of powering up the first transmitter, insert the batteries to the
Weather Station. Once the batteries are in place, all segments of the LCD will light
up briefly. Following time as 12:00 and the Weather man icon will be displayed. If
they are not shown in LCD after 60 seconds, remove the batteries and wait for at
least 60 seconds before reinserting them.
4. The outdoor temperature from the first transmitter (channel 1) should then be
5
7
The Wireless Temperature Sensor (TX29U-IT)

Remote transmission of outdoor temperature to
Weather Station by MHz

Water resistant casing

Wall mounting case (Mounting at a sheltered place.
Avoid direct rain and sunshine)

SETTING UP

When one transmitter is used
1. First, insert the batteries into the Temperature transmitter. (see "Install and
replace batteries in the Temperature transmitter").
2. Immediately after and within 45 seconds, insert the batteries into Weather Clock
(see "Install and replace batteries in the Weather Station"). Once the batteries
are in place, all segments of the LCD will light up briefly. Following the time as
12:00 and the "Weather man" icon will be displayed. If these are not displayed
after 60 seconds, remove the batteries and wait for at least 10 seconds before
reinserting them.
displayed on the Weather Station. Also, the signal reception icon will be displayed.
If this does not happen after 2 minutes, the batteries will need to be removed from
both units and reset from step 1.
5.
Insert the batteries to the second transmitter as soon as the outdoor temperature
readings from the first transmitter are displayed on the Weather Station.
Note: User shall insert the batteries into the second transmitter within 10 seconds of
reception of the first transmitter.
6. The outdoor data from the second transmitter and the "channel 2" icon should then
be displayed on the Weather Station. If this does not happen after 2 minute, the
batteries will need to be removed from all the units and reset from step 1.
7.
Insert the batteries to the third transmitter as soon as the "channel 2" icon and
outdoor data are displayed on the Weather Station. Then within 2 minutes, the
channel 3 outdoor data from the third transmitter will be displayed and the channel
icon will shift back to "1" once the third transmitter is successfully received. If this
the setting up from step 1.
is not happen, user shall restart
Note:

User shall insert the batteries into the third transmitter within 10 seconds of
reception of the second transmitter.

And user may be required to check the displayed readings on the Weather Station
against those shown on the transmitters in order to recognize the Channel No. of
each transmitter.
6
8