Panasonic Diga DMR-ES35V Operating Instructions Manual page 67

Operation
Cannot operate the TV.
Cannot operate the DVD.
Cannot operate the VHS.
The remote control does not work. ≥The remote control and main unit are using different codes. Change the code on the remote
The unit is on but cannot be
operated.
Cannot eject a disc.
Cannot tune channels.
Startup is slow.
Takes time to read DVD-RAM.
Picture
TV reception worsens after
connecting the unit.
The images from the unit do not
appear on the TV.
Picture is distorted.
The TV screen is distorted when
switching the DVD/VHS.
On-screen messages do not
appear.
The grey background does not
appear.
The 4:3 aspect ratio picture
expands left and right.
Screen size is wrong.
There is a lot of after-image when
playing video.
When playing DVD-Video using
progressive output, one part of the
picture momentarily appears to be
doubled up.
There is no apparent change in
picture quality when adjusted with
the Picture menu in the on-screen
menus.
≥Change manufacturer code. Some TVs cannot be operated even if you change the code.
≥Press [DRIVE SELECT] to select the DVD.
≥Press [DRIVE SELECT] to select the VHS.
control.
≥Press and hold [ENTER] and the indicated number button at the same time for more than
2 seconds.
≥The batteries are depleted. Replace them with new ones.
It may be necessary to reset the code on the remote control again after changing the batteries.
≥Point the remote control at the remote control sensor on the main unit.
≥Remove obstacles between the remote control and main unit.
≥Coloured glass may obstruct the signal reception/transmission.
≥Do not place the signal sensor in direct sunlight or in areas that may be subject to sunlight
exposure.
≥The child lock function is activated.
≥Some operations are prohibited by the disc.
≥The unit is warm ("U59" appears on the unit's display). Wait until "U59" disappears.
≥One of the unit's safety devices may have been activated.
Reset the unit as follows:
(1) Press [Í/I] on the main unit to switch to standby.
If the unit does not switch to standby, press and hold [Í/I] on the main unit for about
10 seconds. The unit is forcibly switched to standby.
Alternatively, disconnect the AC mains lead, wait for about 1 minute, then reconnect it.
(2) Press [Í/I] on the main unit to turn the unit on.
≥The child lock function is activated.
≥The unit is recording.
≥The unit may have a problem. While the unit is off, hold down [∫] and [CH, W] on the main unit
simultaneously for about 5 seconds. Remove the disc and consult the dealer.
≥The child lock function is activated.
≥Check the connections.
≥Make sure that "Quick Start" is set to "On".
Even if "Quick Start" is set to "On", startup is slow if the clock is not set, there was a power failure
or the AC plug has just been connected.
≥A few dozen seconds after turning on the unit, you can play a disc or start recording to discs other
than DVD-RAM.
≥Startup takes time for a few minutes after 5:15 a.m. due to system maintenance of this unit.
≥It may take time to read a disc if it is being used for the first time in this unit or it has not been used
for a long time.
≥This can occur because the signals are being divided between the unit and other equipment. It can
be solved by using a signal booster, available from audio-visual suppliers.
≥Make sure that the TV is connected to the VIDEO OUT terminal, S VIDEO OUT terminal or
COMPONENT VIDEO OUT terminals on the unit.
≥Make sure that the TV's input setting (e.g., AV 1) is correct.
≥The TV is not compatible with progressive signals. Press and hold [∫] and [" DVD, COPYING] on
the main unit at the same time for about 5 seconds. The setting will change to interlace.
≥The colour of the screen may turn to monochrome or the screen may be distorted depending on
the TV used when you switch the DVD/VHS. However, this is not a malfunction.
≥Select "Automatic" in "On-Screen Messages" in the Setup menu.
≥Select "On" in "Grey Background" in the Setup menu.
≥Use the TV to change the aspect. If your TV does not have that function, set "Progressive" in the
Picture menu to "Off".
≥Check the settings for "TV Aspect" in the Setup menu.
≥Set "Copy NR" in the Picture menu to "Off".
≥Set "Progressive" in the Picture menu to "Off". This problem is caused by the editing method or
material used on DVD-Video, but should be corrected if you use interlace output.
≥The effect cannot be seen with certain types of video.
Page
15
10
10
15
15
10
10
10
10
10
36
–
64
–
36
–
–
36
12
59
–
–
–
Page
–
12, 13
–
–
–
58
58
35
59
35
35
–
67
RQTV0136