How To Delete A Channel; How To Field Program Radio Options; Table 4: Radio Option Codes - Ritron JMX-111D Operator's Manual

TABLE 2: INTERFERENCE ELIMINATOR
PROGRAMMABLE QC TONE
Code Hz Code Hz
01 67.0 18 123.0
02 71.9 19 127.3
03 74.4 20 131.8
04 77.0 21 136.5
05 79.7 22 141.3
06 82.5 23 146.2
07 85.4 24 151.4
08 88.5 25 156.7
09 91.5 26 162.2
10 94.8 27 167.9
11 97.4 28 173.8
12 100.0 29 179.9
13 103.5 30 186.2
14 107.2 31 192.8
15 110.9 32 203.5
16 114.8 33 210.7
17 118.8 34 218.1
00 Delete
TABLE 3: DIGITAL INTERFERENCE
ELIMINATOR PROGRAMMABLE DQC TONE
CODE NUMBERS
023 074 165 261 356
025 114 172 263 364
026 115 174 265 365
031 116 205 266 371
032 122 212 271 411
036 125 223 274 412
043 131 225 306 413
047 132 226 311 423
051 134 243 315 431
053 143 244 325 432
054 145 245 331 445
065 152 246 332 446
071 155 251 343 452
072 156 252 346 454
073 162 255 351 455
Have questions? Call 800-USA-1-USA (800-872-1872) or visit our website at
RADIO PROGRAMMING

HOW TO DELETE A CHANNEL

1. Follow the instructions in FIG-6 on page
Code Hz
10 to place the radio in the Program /
35 225.7
Readout Mode.
36 233.6
2. Using the CHANNEL button and the
37 241.8
LED display on the front of the radio,
38 250.3
select the channel to be deleted.
39 69.4
40 159.8
3. Enter 4-digit code "0000" as described in
41 165.5
the "How to Field Program Frequency &
42 171.3
Tone Codes" section on page 11.
43 177.3
4. When all four digits are programmed,
44 No Tone
press and release the On / Volume Up
45 183.5
to SAVE your programming entry. The
46 189.9
47 196.6 LED display will briefly show the channel
48 199.5
number you have just deleted and the
49 206.5
radio will sound a triple beep to indicate
50 229.1
that channel deletion was successful.
51 254.1
5. To delete another channel, repeat steps
2 through 4.
6. Turn the radio OFF and then ON
again—the radio is now ready to use.
7. The remaining channels are in the same
sequence and will retain their same
462 631
464 632 channel number. The Channel Selector
465 645
will skip over the deleted channel
466 654
numbers.
503 662
NOTE: If all channels are deleted the radio
506 664
516 703
523 712
532 723
546 731
565 732
606 734
612 743
624 754
627
will not operate, instead it will turn
on in Field Program mode to allow
entry of a valid frequency and tone
code.

HOW TO FIELD PROGRAM RADIO OPTIONS

1. Follow the instructions in FIG-6 on page
10 to place the radio in the Program /
Readout Mode.
2. Using the PTT (push-to-talk) button and
the LED display, enter the single digit
code from Table 4 below for the option
to be programmed.
3. Pause—the display will change and
show a hyphen, you will also hear a
short low tone.
4. Press and release the On / Volume Up
to SAVE your programming entry. The
radio will sound a triple beep to indicate
that programming was successful.
5. Turn the radio OFF and then ON
again—the radio is now ready to use.

TABLE 4: Radio Option Codes

Option
Turn Channel Scan
Turn Channel Scan OFF
Turn Weather Channel
Turn Weather Channel OFF
Turn Weather Alert
Turn Weather Alert OFF
Turn Speaker Beep
Turn Speaker Beep OFF
www.ritron.com
Code
ON 1
2
ON 3
4
ON 5
6
ON 7
8
13