Ch. (Channel) Add/Del; Tuning Band - Zenith SENTRY 2 SAR2035Y7 Operating Manual & Warranty

•SETUP MENU
CH. (Channel) ADD/DEL
Lets you add channels to and remove channels from the ac-
five channels found when using the AUTO CH. SEARCH
option. In this way you can customize the channels that are
a_ through CHANNEL (CH) Up/Down.
CH. ADD/DEL is an optional feature.You do not have to
activatethis feature in order to use your TV.
Before Using CH. ADD/DEL
Use the AUTO CH. SEARCH feature, if not previously
used when you first installed the TV.
To Add a Channel to Scan Sequence
I. CH. ADD/DEL display should be shown on the TV
if you followed the "Basic Menu Operation" given
in the "On-Screen Menus" section.
AUTO CH. SEARCH
-- > CH. ADD/DEL
3X2NING BAND
AUTO FINE TUNE
CLOCK SET
CAFYIONS
CH. ADD/DEL
CH2
ADDED
PRESS ADJUST
KEY TO CHANGE
Selecting Ch. Add/Del Ch. Add/Del Display"
2. Using CHANNEL (CH) Up/Down go to the nearest
channel ABOVE the channel you wish to add.
3. Press SELECT to go down to the channel you wish
to add.
4.Add channel by pressing ADJUST (ADJ)
Left/Right until the display shows ADDED.
5. Press ENTER (ENT) to return to normal TV viewing.
To Delete a Cham_ from Scan Sequence
I. CH. ADD/DEL display should be shown on the TV
if you followed the "Basic Menu Operation" given
in the "On-Screen Menus" section.
2. Using CHANNEL (CH) Up/Down go to the channel
you wish to remove.
3. Remove channel by pressing ADJUST (ADJ)
Left/Right until the display shows DELETED.
4. Press ENTER (ENT) to return to normal TV viewing.
When Some Channels Can Not Be Tuned
If you have some difficulty tuning some channels, you may
have to manually set the TUNING BAND option. If you
have the correct band, but are still having difficulty finding
a channel you Imow to be active, set the AUTO FINE
TUNE to SEARCH.
TUNING BAND
Purpose
Allows for setting the TV tuner to
match
your antenna or
cable-TV system.
If you are having difficulty tuning channels, the TUNING
BAND may have to be set manually to match your viewing
needs.
Before Using TUNING BAND
Connect and turn ON all external equipment, such as cable-
TV decoder, VCR, etc. Use AUTO CH. SEARCH if not
previously used.
NOTE: TUlqING BAND is not displayed while AUX chan-
nel is being used.
To Use TUNING BAND
1. TUNING BAND display should be shown on the TV
if you followed the "Basic Menu Operation" given
in the "On-Screen Menus" section.
f
AUTO CH. SEARCH
CH. ADD/DEL
-- > TUNING BAND
AUTO FINE TUNE
CLOCKSET
CAPTIONS
Selecting Tuning Band
TUNING BAND
BROADCAST
PRESS ADJUST
KEY TO CHANGE
Tuning Band Display
2. Press ADJUST (ADJ) Left/Right to select the
desired tuning band, as follows:
• BROADCAST is used for standard "over-the-air"
broadcasts.
• Cable - CATV is used for most standard cable-TV
(CATV) systems.
• Cable - HRC is used for cable-TV systems that use
HRC (Harmonically Related Carder).
* Cable - ICC is used for cable-TV systems using ICC
(Incremental Coherent Carder).
Available Channels per Band
The channels that are available in the broadcast and cable
tuning bands are shown below:.
BROADCAST Band
VHF 2to13 UHF 14to69"
* Channels above 69 are not selectable.
CATV, HRC and ICC Bands
I to 125"*
** Channels above 125 may not be selectable.
When Some Channels Are Not Clear
Ifs°me channdsarenot dear'changetheAUTO FINETUNE"
You may have to trydifferent TUNING BAND and AU'IV
FINE TUNE settings until you l_t a dear pictme, channel-to-
ctmneL Refer to the AUTO FINE TUNE optioa for dctai_
259vo 8 - 2