Table of Contents
Advertisement
GUIDE Plus+ System
Problems
GUIDE
Plus+
setup
won't
switch
to channel
9 for VCR and/or
channel
02 cable
box
Make" sure you
hav_" r_'movcd
the" I)_'mo
Pin from the" (3 LINK jack.
Check
to s_'_, if the" (3 LINK wands
fire position_,d
correctly
in
front
of
coH]pon_'nts
> r(_l]3ot_
_ s_nsors.
GUIDE
Plus+ system
control
of cable
box is slower
than
direct
control
of the box
itself. Keep
this in mind
when
changing
channels.
You may
have
an incorrect
GUIDE
Plus+
Channel
Lineup.
Fhe
guide
may get out of sync with
tim cable
provider.
Use tim G_TI)E
Plus+
Setup in the
GblI)E
Plus+ Me_tu to change
the zip code
to 99999.
Turn
the ['V off for 10 minutes.
Use Setup
again
to change
the zip code
back to the correct
value.
If asked,
be sure to select
the correct
channel
lineup
f)om the on screen
list.
Program
information
doesn't
download
R_'vi_'w your
s_'tup
inf_)rmation
and make
sure its correct.
Press MEN[} on the" r_'mot_" and s_qcct G'Ull)t;l_htx+
5etl@. Go to page" 16
for dctail_'d
instructions
about
th_ _ GUII)E
Plus+
S_'tup m_qms.
The" TV must
[)_ off to download
infi_rmatk_n.
L_'aw" your
TV off overnight
for fit h'ast 10 hours
to r_,c_,ivc the" initial download
for
your
area.
If you're
using
a cable
box,
leave
it on so you
can receive
program
infi)rmatk)n.
Scheduled
Watch
or Record
doesn't
occur
Ch_,ck Sch_,duk, for tim_q conflicts.
Go to page, 50 fi_r instructions.
Make" sun _ the" wands
of the (3 LINK cabh,
arc placcd
in front
of the" remote,
s_'nsor(s)
on the" compon_'nt(s).
Make
sure your VCR is Wrned
off during
tim time
you've
scheduled
to record
a program
because
the system
turns
the VCR on when
it starts recording
(if it's already
on when
recording
starts,
the system
will turn
it off).
Make
sure there
is a tape
in the VCR and that the VCR is connected
properly.
Be sure that
you set tip the VCR in tim G_JI)t,2 l'hts+
5etz@ menus
If you
don't
complete
the (2ot_/_igguri_1<g,ibra I'(]1¢ steps
successf_illy,
the Record
option
won't
be available.
Go to p. 18 fi)r detailed
instructions.
If a cable
box
is attached
to your TV make
sure you
set it tip correctly
in the
GUll)t;l'lus+
<Setup menus.
Go to page
16 17 R)r
detailed
instmctk)ns.
The Remote
Control
Doesn't
Work
Something
might
be between
the remote
and tim remote
sensor
on tim component.
Make
sure there
is a clear
path.
Maybe
the remote
isn't aimed
directly
at tim component
(TV or VCR) that you're
twing
to operate.
Maybe
remote
is not in FV Mode.
Press the TV button
so remote
will control
TV.
Maybe
batteries
in remote
are weak,
dead
or installed
incorrectly.
Put new batteries
in the remote.
(Note,
if you
remove
the
batteries,
you may
have to reprogram
the remote
to operate
other
components.)
You might
need
to drain
the remote's
microprocessor:
remove
batteries
and press
tim number
1 button
for fit least 60 seconds.
Release
the
1 button,
replace
the batteries,
and (if necessa
W) program
the remote
again.
56
Chapter
5
Advertisement
Table of Contents
