Cancel • Off; Clock; Tones; Timer - Whirlpool g2microven GH9177XL Use & Care Manual

Speedcook appliance
Hide thumbs Also See for g2microven GH9177XL:
Table of Contents

Advertisement

The START control willstart a nyfunction.
Ifcooking i sinterrupted,
touching t heSTART control padwill
resume thepreset cycle.
For a dded convenience,
the"Start" touch pad isalso available on
some display screens, andprovides thesame function a sthe
START control pad.
Five oftheJET COOK
TM
controls share function with the
numerical pads 1-5. When one of these JET COOK
TM
controls is
touched (while no function is operating), the oven will begin
cooking at high power for 1-5 minutes, depending on which pad
is touched. After cooking begins, the JET COOK
TM
controls
return to their normal numerical pad function.
The JET COOK FOR 30 SEC. control starts the oven at 100%
power for 30 seconds, and adds 30 seconds of cook time with
each additional touch of the control. Once cooking begins, cook
power or cook time may be changed manually by touching the
appropriate
display area and entering the numerical information.
The CANCEL*OFF
pad stops most functions except for the
Timer, Child Lock and Learning Mode.
The oven will also turn off when the door is opened. Close the
door and touch START or the "Continue" display area to resume
the cycle. A sensor cooking cycle may not be resumed if
interrupted by opening the door.
This is a 12-hour clock, showing a.m. and p.m. When power is
first supplied to the oven, or after a power failure, the "Home"
screen will appear.
To Set Clock: Touch CLOCK, and follow directions.
To Hide Clock: Touch CLOCK, then touch CANCEL,OFR
"Home" will appear in place of the time of day on display screen.
To Display Clock: Touch CLOCK, then touch START.
Tones are audible signals, indicating the following:
One tone
Valid entry(short
beep)
End of Timer countdown (long tone)
Two tones
Reminder (short beeps), repeat each minute for 15 minutes
after the end-of-cycle
tones
Between stages (short beeps)
Three Tones
Invalid entry (short beeps)
Four tones
End of cycle (long tones)
To Disable Tones: Turn volume off using the "Hints & Settings"
menu.
The Timer can be set in minutes and seconds, up to 90 minutes,
and counts down the set time.
NOTE: The Timer does not start or stop the oven.
16
Nenu
1. Timer countdown
When the Timer is in use, the oven can still operate. During an
oven operation, "Timer" will appear in the upper, right-hand
corner of the display. The countdown
may also be seen by
touching TIMER SET/OFR Touch "Return" to go back to the
previous screen or wait for the timer to end. If the timer ends
while oven is still operating, the tone will sound and the display
will return to the set operating mode.
To Set: Touch TIMER SET/OFF, enter desired time and touch
"Start." The time can be reset during the countdown
by touching
TIMER SET/OFE entering a new time, then touching the START
pad.
To Cancel: Touch TIMER SET/OFF twice.
The vent fan has 4 speeds ranging from Off to High.
To protect the oven, the vent fan will automatically
turn on at high
speed if the temperature
from the range or cooktop below gets
too hot. It may stay on for up to 1 hour to cool the oven. When
this occurs, the Vent Fan pad will not function.
A few seconds after the last time the Vent Fan pad is
touched, the screen returns to the previous display.
The first time the vent fan is turned on after power is
connected to the oven, the fan will start at high speed. The
next time the vent fan is turned on, it will start at the last
speed used.
To Turn Vent Fan On/Off: Touch VENT FAN to turn fan on, then
touch "+" or "-" on the display screen to select fan speed. Touch
the Vent Fan pad twice to turn the fan off (or once if Fan screen is
active).
The cooktop/countertop
light has numerous brightness settings
ranging from Off to High. The light can be turned on manually, or
the Night Light can be programmed
to come on automatically
when the sensor detects low light level. See "Night Light"
section.
To Manually Turn Light On/Off: Touch the LIGHT control pad to
turn light on. Touch "+" or "-" on the display screen to set desired
brightness level. Touch LIGHT pad twice to turn light off (or once
if Light screen is active).

Advertisement

Table of Contents
loading

Table of Contents