Table of Contents
Advertisement
C@nnecti@ns
Ne :up
Using Automatic
Code Search (continued)
Continue pressing PLAY nnti_ the compotlent
turns off or the component
button (II)VD, \.CR) light on the remote
turns off. if the comp®nent
button ligh_ tun_s off, thc'n MI codes f_r that partic@ar component
ha_e been tested
once. If d_e component
does aot rum off, then the remote can't be programmed
to operate
that component.
[f the component
yon want to control does _urn oh::
1.
Plvss and release REVERSE, then wait 2 se<_mds. Repeat fills step unti the device turns back ON.
2.
"R) finish, press and hold STOP until tt_e componen_
button (I)VD, VCR) hight on {he remo_e turns oil A code that
contro s yo_lr component
has been saved to that remote button.
Using Direct Entry
1,
Turf7 on the component
to be programmed.
2.
Look up _he brand and code number(s)
k>r the component
on the code list m tills section.
A
Press and hold the conponenl:
but:to_ you want to prngram on [he remote.
4.
Enter {he code from the remote controI code list on the tbliowiJ_g pages. ]f the (::ompoaer_t button (DVD, VCR)
iight on the remote flashes, you have either entered
an i_valid ('ode or the butm:a isn't programmable.
5.
Release the componerH: button, poi_l[ tile R'nlotc' at the component
and then press ON,,OF[; to see if the
eompone_t
responds
to tile command.
If it doesn't,
tW pressing the compor_ent butRm anti then ON,OFF
again.
,,
]f you g_:t no response,
repeat fl:ese steps using the next code listed R_r your brand, until _he component
responds
to the remote cxmnna_qds.
*
l_ yew try all the codes tr_)ryour component
bmr_d arid none work, tW %e automatic
code search method. If
automa ic code search doesn't fred the code, the remote is _mt eompatibIe
with your eompor_ent.
How to Use the Remote
A er
You've
Programmed
It
lR_caus< " this univcr_a[ remote can control dill;trent (ompon_nts
(TV, DVD, VCR) it use_, operational
modes triggered
by the (x>mponent buttons. For example,
if you want the remora _o control the TV, yoLl would press the TV button to
put the remora into '1%'mode before you cot_id conttxi the TV
1.
Press the appropriate
component
button (VV, DVD, VCR) _o set the remote to control the componem.
2
Press ON-OFF
to turn {he component
on or off\
3
Use the remote buttons flint appl_ to dat component.
Notes: Tl.:_e remote m@: Hot &, compat_Me wiff._a!/ brands and modds of compo*_e*_ts. B aIso m@: not operc,_
all fi__ctJons q!the *wmoW that cg_me u,_Th,yo*_rcoat,portent
g'yc,,_ ke,:7_) pr,:,sx*n:¢buttons a*_d nothing happeltx, the ,emote i:_ proba5{l' in the tvt>*g mode_ lq:m m_tsl pr_ss
the com[_otzent
bt_tgon
that
matcb{,s
the co*at[:o*_e*_t you
_,ant
Io (g)erz*t_' (Le+, (fl Fou
g_'a*_t t(* (p_'*_:te
the
L)I'D
pla3'_:_; pr_'ss
L)t 7.) o_ the
tz, n_ote
c(:n_trol
to put
the _'_tOte
i_ I) VI) mode'.
)
Using the INPUT Button
[se _he :INP[YI_button to scroll through the avai_:_ble input channels
and view eon_ponents
you have c(mnected
to the
TV.
1.
:Press TV to place the remote in TV mode. Make sure the component
you want to view is turned on,
2.
Press INP[T to tune to an available [*_put ch;mnel.
3.
Ib return to the channel you were previously
w:m'hing on TV, p_'ss CH+ or CH- or use buttv)*_s 0-9 to enter the
channd
number.
Chapter
_
_9
Advertisement
Table of Contents
