Table of Contents
Advertisement
Troubleshooting
\']cYst
I)rob]elnS
yOll
encounter
\\-Jill
your
Z\,'
(}in
lse
(2orre(ted
lyv
consulting
tile
following
£rolliY]eSl]OO/ing
list.
TV Problems
TV won't
turn on
*
Mako sure tho TV is pluggod
in.
-
Check
tile \\-all receptacle
(or extension
cord)
to make
sure
it is "live" by plugging
in something
else.
-
The front panel
controls
may lye ]ocke(I
(disabled).
Use the remote
control
to unlock
the fiont panel
controls
by
selecting
tile ]:,>tzt ]'(ltz(,l J_,loc[_in tile ])(l?'(,lzl(ll (otgD'ol Inenu
and press
OK to uncheck
the box.
No picture,
no sound but TV is on
®
_Oll lllight be tuned to
:in
input
\\Jill no device connocted
to it to view. If you're trying to view a connected
device
press INP( TT until the picture from that device appears
or press ANTENNA to watch T\.'.
•
Maybe the ,S)_,_al soz_r(e option is set incorrectly.
Go to page 38 for (letai]e(I instructions.
-
The channel might lye blank -- change
channels.
-
If you're watching your VCR and it's connected
with coaxial came to the ANALOG or DIGITAL INPUT jack, tune
the T\.' to channel 3 or 4 (\vhichever
channel is selected on the 3/4 switch on the back of your VCR). Also check to
make sure the TViVCR button on the VCR is in the correct mode (press the TViVCR button on your VCR).
Sound okay, picture poor
'_
If you'_'e getting a black :rod white
[)i('ture
froln a devico
yOLl_Ve
connected
to yotu T\.', you might have your video
cables connected
to the wrong jacks. A yellow Video cable connects to the yellow VII)EO input jack on the side
of your TV; three yell()\\- video cables or bundled
component
video cables (red, blue, and green) connect to the
COMPONENT INPUT jacks on the back of your TV.
,_
If you're getting no picture from a device you've connected
to your T\.', you might have your vide<) cable connected
to the MONITOR OUT jacks on the back of your T\.'. These jacks are used to connect recording
devices. A yel]ox\-
Video cable connects
to the yell()\\- VIDEO input jack on the side of your T\,".
•
Check antenna
connections.
Make sure all of the cables are firmly connected
to the jacks.
-
Try a(Ijusting sharpness
function to improve weak signals. Go to [)age 37 for more instructions.
Sound poor, picture
okay
-
Maybe the sound is muted.
Try pressing the volume up button to restore sound.
-
If using S-Video or Y, PB, PR, remember
to also connect the device's lef} and right audio output jacks to the TV's L
and R Audio Input jacks.
-
The sound settings can lye adjusted and may not lye adjusted correctly. Go to page 34 for more information.
•
The internal speakers
might lye turned off. Go to page 36 for more information.
•
The speaker wire might lye inserted
too far into the terminal hole. Make sure only the exposed
wire is inserted
into
the hole, not the plastic part of the conductor.
•
If there is no bass sound or the bass sounds poor, it could lye because
the speaker
\vires aren't connected
correctly.
Make sure the \\-ire connected
to the red terminal on the speaker
is connected
to the red terminal on the TV, and
black matches to black. Go to page 7 for more information.
Advertisement
Table of Contents
