Advertisement
SAFETY
CONSIDERATIONS
Improper installation,
adjustment,
alteration,
service maintenance,
or use
can
cause
explosion,
fire,
electrical
shock,
or other
conditions
which
may cause
death,
personal
injury,
or property
damage.
Consult
a qualified
installer,
service
agency,
or your
distributor
or branch
for information
or assistance.
The qualified
installer
or agency must use factory-authorized
kits or accessories
when modifying
this product.
Refer to the individual
instructions
packaged
with the kits or accessories
when
installing.
Follow
all safety codes. Wear safety glasses,
protective
clothing,
and work gloves.
Have a fire extinguisher
available.
Read
these
instructions
thoroughly
and
follow
all warnings
or cautions
included
in literature
and
attached
to the
unit.
consult
local
building
codes,
the current
editions
of the National
Fuel
Gas
Code
(NFGC)
NFPA
54/ANSI
Z223.1,
and
the
National
Electrical
Code (NEC) NFPA 70.
In Canada
refer to the current
editions
of the National
Standards
of Canada
CAN/CSA-BI49.1
and .2 Natural
Gas and Propane
Installation
codes, and Canadian
Electrical
Code CSA C22.1
Recognize
safety information.
This is the safety-alert
symbol/_.
When
you
see this symbol
on the unit
and in instructions
or
manuals,
be alert to the potential
for personal
injury.
Understand
these
signal
words:
DANGER,
WARNING,
and
CAUTION.
These words
are used with
the safety-alert
symbol.
DANGER
identifies
the most serious hazards
which will result in severe per-
sonal injury
or death. WARNING
signifies
hazards
which
could
result in personal
injury or death. CAUTION
is used to identify
unsafe
practices
which
may
result
in minor
personal
injury
or
product
and property
damage.
NOTE is used to highlight
sugges-
tions which
will result in enhanced
installation,
reliability,
or op-
eration.
Note: Installer:
This manual
should be left with the equipment
user.
FIRE, EXPLOSION,
ELECTRICAL
SHOCK
HAZARD
Failure to follow this warning
could result in personal
injury,
death or property
damage.
Installation
and servicing
of this equipment
can be hazardous
due to mechanical
and electrical
components.
Only trained
and qualified
personnel
should
install, repair, or service
this
equipment.
FIRE AND EXPLOSION
HAZARD
Failure to follow this warning could result in personal injury,
death, and/or property damage.
What to do if you smell gas:
1. Do not try to light any appliance.
2. Do not touch any electrical switch; do not use any phone in
your building.
3. Leave the building immediately.
4. Immediately call your gas supplier from a nearby phone.
Follow the gas supplier's instructions.
5. If you cannot reach your gas supplier, call the fire
department.
ELECTRICALSHOCK
HAZARD
Failure
to follow this warning
could result in personal
injury
and/or death.
Before
performing
recommended
maintenance,
be sure the
main power
switch
to unit is turned off and lock-out
tag is
installed.
FIRE,
EXPLOSION,
ELECTRICAL
SHOCK
HAZARD
Failure to follow this warning
could result in personal iniury,
death and/or property
damage.
1. Do not turn off the electrical
power
to unit without
first
turning
off the gas supply.
2.
Before
attempting
to
start
the
gas
heating
section,
familiarize
yourself
with
all the procedures
that
must
be
followed.
FIRE,
EXPLOSION
HAZARD
Failure to follow this warning
could result in personal iniury,
death, and/or property
damage.
Do not store or use combustible
materials,
gasoline,
or other
flammable
vapors
and liquids
in the vicinity
of this or any
other appliance.
FIRE,
EXPLOSION
HAZARD
Failure to follow this warning
could result in personal iniury,
death, and/or property
damage.
Do not attempt
to light by hand.
FIRE,
EXPLOSION,
ELECTRICAL
SHOCK
HAZARD
Failure to follow this warning
could result in personal iniury,
death or property
damage.
Do
not use this
unit if any part has
been
under
water.
Immediately
call a qualified
service technician
to inspect the
unit and to replace
any part of the control system
which
has
been under water.
CUT HAZARD
Failure to follow this caution may result in personal injury.
When removing access panels or performing maintenance
functions inside your unit, be aware of sharp sheet metal parts
and screws. Although special care is taken to reduce sharp
edges to a minimum, be extremely careful when handling
parts or reaching into the unit.
Advertisement
