Table of Contents
Advertisement
INS TALLA TION
Television
Location
This unit can be used as part of an entertainment
center
Consult
your dealer for available
options
Avoid
excessive
sunlight
or bright
lights,
including
reflections.
Keep away from excessive heat or moisture. Inadequate
ventilation may cause internal component failure.
Fluorescent
lighting
may
reduce
remote
control
transmitting range.
Keep away from magnetic equipment,
including motors,
fans and external speakers.
Component
Connection
Cables
Shielded
audio
and video cables
should
be used between
components.
For best results:
Use 75-ohm coaxial shielded cables.
Use appropriate input and output connectors, that match
your component connectors.
Avoid long cables to minimize interference.
AC Power
Supply
Cord
CAUTION:
TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT
OF AC OUTLET AND FULLY INSERT. DO NOT
Polarized plug
USE A PLUG WITH A RECEPTACLE OR OTHER
OUTLET UNLESS THE BLADE CAN BE FULLY INSERTED TO
PREVENT BLADE EXPOSURE.
PROTECT POWER CORDS FROM BEING WALKED ON, ROLLED
OVER, CRIMPED, BENT, OR PINCHED, PARTICULARLY AT PLUGS,
CONVENIENCE RECEPTACLES,AND THE POINT WHERE THEY EXIT
FROM THE APPARATUS.
Cable / Antenna
Connection
For proper
reception
of analog
or digital cable
channels,
a
cable service
connection
is required.
Cable Connection
Incoming
Cable from
Cable Company
Connect the cable supplied
by your local
cable company
to ANTENNA
(A)
connection
on back of television.
Select
Cable mode and ANTENNA
(A) in SET UP
menu
under
Program
CH
(Program
Channels).
Antenna
Connection
Note:
75 Ohm ANT A
For proper reception of digital and analog VHF/
UHF channels, an external antenna is required. For
best
reception
an
outdoor
antenna
is
recommended.
Connect home antenna to
IncomingCablefrom
either ANT (A) or ANT (B)
HomeAntenna
connection on back of
the
television. Select Antenna
_"
mode for ANTENNA (A) or
(B) in Input Setup under
Program CH in Setup menu.
Cable Mode is preset at the factor_ Antenna users must
change to ANTENNA
Mode for ANTENNA (A) in the Set
Up menu.
If you have both
Cable and Antenna,
the
Cable must be connected to ANT (A).
First Time Setup
For your
convenience,
First
Time
Set
up menu
will
be
displayed
on screen
when the set is turned
on for the first
time.
If
needed,
follow
the
menus
and
procedures
displayed
on-screen
for setting
up the features.
Input Setup
To select
the configuration
of RF input depending
on the
signal source.
Note:
No video will be displayed in this setup mode.
Procedure
Press VOL b" to select Cable only, Cable/Antenna
or
Antenna only.
Press the OK button to underline your selection.
Cab_ o_ly
When the next screen is displayed,
press OK button to
start the Auto Scan. All available channels with a signal
will be programmed into memory.
Auto
Scan
This feature allows you to selectively auto scan channels.
You can Scan All, Analog only channels or Analog & Digital
channels.
Procedure
Press OK button to start Auto Scan,
Auto Scan
Notes:
After Auto Scan is completed the PTV tunes to the first
channel found during auto scan.
If the EXIT button is pressed
at anytime during auto
scan, the First Time Setup menu will be cancelled and
the PTV will tune to analog channel 2 on ANTENNA (A).
If a DCM (Digital Cable Module) is present during the
First Time
Setup and Antenna
(A) is set to cable,
Antenna
(A) will not be scanned
due to the DCM
providing the channel map.
Convergence
This menu lets you set the green CRT alignment and the center
convergence,
Follow the instructions
on-screen
to perform
convergence, After convergence is performed, press EXIT to
return to normal viewing,
40
Advertisement
Table of Contents
