The Installation Space; Dimensions And Clearances - GE Monogram ZISB420DRK Design And Installation Manual

Design Guide
THE INSTALLATION SPACE
36" Models12"
42" Models18"
48" Models20"
75"FromFloor
to Bottom
ff Electrical
Area
*The finished cutout width must be:
35-1/2" fin" 36" models
41-1/2" for 42" models
47-1/2" fin" 48" models
Water And Electrical Locations
The opening must be prepared with the electrical
and water supi)ly located as shown.
The cutout
depth
must be 24"
The refrigerator will project fin'ward, slightly beyond
ac!jacent cabinetry, depending on yore" installation.
Cutout
depth
beneath a soffit:
When installed beneath a soffit, the soffit cannot
exceed the 24" installation depth shown. The top case
trim overlaps the bottom of the soffit.
Additional Specifications
• A 115 _olt 60Hz., 15 or 20 amp power suppl_ is
required. An indixidual properl) grotmded branch
circuit or circuit breaker is recommended. Install
a I_r° I_erlv, ,gr°tmded 3-i_ron _, electrical receptacle
recessed into the back wall. Electrical must be
located on rear wall as shown.
NOTE: GF] (grotmd tault interrupter) is not
recoi/llllended.
• Water line can enter the oi_ening, through, the floor
or back wall. The water line should
be 1/4" O.D.
S _ ) ii
copper tubing or (;E _martC_ nnect kit between
the cold water line and water connection location,
long enough to extend to the front of the
refrigerator. Installation of an easily accessible
shut off xalxe in the water line is required.
DIMENSIONS AND CLEARANCES
83 2
Rea
25-3/8" FramedModels
35", 41", or 47" _ 25-3/4"StainlessSteel Models
]._aCase W idth_..] * Shippingheight.The
refrigeratorcan be
adjustedto fit into a
cutoutthat is 83-1/2"
min. to 84-1/2"max.
• 84" From height. Note that the
Floorto top casetrim at the
Top Frame front is 1/2" higher
andwill overlap
uppercabinetryor
soffit. Useleveling
legs andwheels for a
maximum1" height
adjustment.
36", 42" or 48"
Frame to Frame
DepthincludingHandles:
26-7/8"FramedModels
27-3/4"StainlessSteelModels
28-11/16"Professional M odels
Product Clearances
These refrigerators are equii_ped with a 2 position
door stop. The tactorv set 130 ° door swing can be
a(!justed to 90 ° if clearance to a(!jacent cabinets or
walls is restricted.
130° DoorSwing
,J
90° DoorSwing
23=7/8"
Behind
Frame
l
C
Models A B C *Min. Distance
to Wall
36" 13" 15" 20-5/8"
42" 13" 19" 26-5/8" '4" Stainlessand
48" 15" 20" 28-5/8" TrimmedModels.
5" ProSeries
Allow minimmn clearances for fl'eezer door
(Dimension A) and fresh ti)od door (Dimension B)
tot a flfll 130 ° door swing and to allow tot pan
I'eII/ox_ll.
For a 90 ° door swing, allow 4" rain. clearance
to a wall, for framed and stainless steel models.
Allow 5" rain. clearance for professional series models.
If the 90 ° door stop position is used, pan access is
maintained, but pan remoxal is restricted.
See illustrations pages 4 and 5 to determine
door swing interaction with ac!jacent cabinets or
cot/ntertol) S.