Advertisement
approximate and may vary depending
upon soil conditions, height of grass and
types of grass being mowed.
• The average lawn should be cut to
approximately 2-1/2 inches dudng the
cool season and to over 3 inches during
hot months. For healthier and better
looking lawns, mow often and after
moderate growth.
• For best cutting performance, grass
over 6 inches in height should be
mowed twice. Make the first cut rela-
tively high; the second to desired height.
TO ADJUST GAUGE WHEELS
Gauge wheels are propedy adjusted
when they are slightly off the ground when
mower is at the desired cutting height in
operating position. Gauge wheels then
keep the deck in proper position to help
prevent scalping in most terrain condi-
tions.
• Adjust gauge wheels with tractor on a
flat level surface.
• Adjust mower to desired cutting height
(See "TO ADJUST MOWER CUTTING
HEIGHT" in the Operation section of
this manual).
• With mower in desired height of cut po-
sition, gauge wheels should be assem-
bled so they are slightly off the ground.
Install gauge wheel in appropriate hole
with shoulder bolt, 3/8 washer, and 3/8-
16 Iocknut and tighten securely.
° Repeat for opposite side installing
gauge wheel in same adjustment hole.
Gauge
Mounffng_
Bracket
_,CAUTION:
Do not operate the mower
without either the entire grass catcher, on
mowers so equipped, or the discharge
guard in place.
TO OPERATE ON HILLS
_,CAUTION:
Do not ddve up or down
hills with slopes greater than 15° and do
not drive across any slope. Use the slope
guide provided at the back of this manual.
• Choose the slowest speed before start-
ing up or down hills.
.
• Avoid atopp|ng or changing speed on
hills.
• If slowing is necessary, move throttle
control lever to slower position.
i
f stopping is absolutely necessary, push
clutch/brake pedal quickly to brake posi-
tion and engage parking brake.
Move motion control lever to neutral (N)
position.
IMPORTANT: The motion control lever
does not return to neutral (N) position
when the clutch/brake pedal is depressed.
• To restart movement, slowly release
parking brake and clutch/brake pedal.
• Slowly move motion control lever to
slowest setting.
• Make all tums slowly.
Attachment Clutch
Switch Pull Out To
"Engage" _
Push In To
_
"_"
"Disengage"
"-_) )_
Attachment Lift Lever
High Position
/
Low
.#"Positlon
,:.'_.:"
Discharge
;\ Guard
3/8-16
LoCi.nut
Shoulder Bolt
-3/8 Washer
Gauge Wheel
TO OPERATE
MOWER
Your tractor is equipped with an operator
presence sensing
switch.
Any attempt by
the operator to leave the seat with the
engine running and the attachment
clutch
engaged will shut off the engine.
• Select desired height of cut.
• Lower mower with attachment
lift con-
trol.
• Start mower blades by engaging attach-
ment clutch control.
• TOSTOP
MOWER
BLADES
- disen-
gage attachment
clutch control
TO TRANSPORT
When pushing or towing your tractor, be
sure to disengage transmission by placing
freewheel
control in freewheeling
posi-
tion. Freewheel control is located at the
rear drawbar of tractor.
• Raise attachment lift to highest position
with attachment
lift control.
• Remove retainer spring from freewheel
control rod.
• Push control rod in to disengage
trans-
mission and reinsert retainer sp.dng into
control rod hole now on back side of the
bracket.
• 0o not push or tow tractor at more than
two (2) MPR.
• To reengage transmission,
reverse
above procedure.
15
Advertisement
