Specifications; Safety Precautions; On/Off Switch; Adjusting Belt Tracking - Craftsman 351.215140 Operator's Manual

SPECIFICATIONS
Belt size .................................... 4 x 36"
Belt platen area ............................... 5 x 9"
Belt speed ................................ 1100 FPM
Disc diameter .................................... 6"
Disc speed ............................... 2:200 RPM
Table dimensions ............................. 5'/2x 7"
Table tilts ................................... 0 to 45°
Dust port diameter ................................ 2"
Base dimensions ............................ 10 x 16"
Switch ............................. SP, Looking rocker
Weight ...................................... 49 Ibs
WARNING: Operation of any power tool can result in foraign
objects being thrown into the eyes, which can result in severe
eye damage. Always wear safety goggles complying with
United States ANSi Z87.1 (shown on package) before com-
mencing power tool operation. Safety goggles are available at
Sears retail stores or catalog.
CAUTION: Always ebseP/e following safety precautions.
SAFETY PRECAUTIONS
• Whenever acljusting or replacing any parts on the tool, turn
switch OFF and remove the plug from power source.
• Recheck table handle and bolts. They must be tightened
securely.
• Make sure all guards are propedy attached. All guards
should be securely fastened,
• Make sure all moving parts are free and clear of any
interference.
• Make sure all fasteners are tight and have not vibrated loose,
• With power disconnected, test operation by hand for clear-
ance and adjust if necessary.
• Always wear eye protection or face shield.
• Make sure abrasive belt always tracks properly. Correct
tracking gives optimum performance.
• After turning switch on, always allow belt and disc to come
up to full speed before sanding or grinding.
• Be sure disc turns counterclockwise. Abrasive belt must
travel downward.
• Avoid kickback by sanding in accordance with the direction-
al arrows.
* Keep your hands clear of abrasive belt, disc and all moving
parts,
• For optimum performance, do not stall motor or reduce
speed. Do not force the work into the abrasive.
• Always support workpiece with table or work stop when
sanding with belt and with table when sanding with disc.
• Never push a sharp comer of the workpiece rapidly against
the belt or disc. Abrasive backing may tear.
• Replace abrasives when they become loaded (glazed) or
frayed.
WARNING: Some dust created by power sanding, sawing,
grinding, drilling and other construction activities contains
chemicals known to cause cancer, birth defects or other
reproductive harm.
Some examples of these chemicals are:
• Lead from leed.-basad paints.
• Crystalline silica from bricks and cement and other mason-
ry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these e_posures vary, depending on how often
you do this type of work. To reduce your exposure to these
chemicals: work in a well ventilated area and work with
approved safety equipment. Always wear MSHA/NIOBH
approved, properly fitting face mask or respirator when using
such tools.
ON!OFF SWITCH
Refer to Figure 10.
The ON/OFF switch is located on the upper front dght of the
base. To turn the sander ON, pull the switch to the up
position. To turn the sander OFF, push the switch to the down
position.
The sander can be locked from unauthorized use by locking
the switch. To lock the switch:
• Turn the switch to OFF position and disconnect sander
from power source.
• Pull the key out. The switch cannot be turned on with the
key removed.
NOTE: Should the key be removed from the switch at the ON
position, the switch can be turned off but cannot be turned on
again.
• To replace key, slide key into the slot on switch untilit snaps.
10- Locking Switch in OFF Position
ADJUSTING BELT TRACKING
Refer to Figure 11, page 7.
• Quickly turn the switch ON and OFF to check the tracking.
Belt should ride centered on idler and drive drums. Adjust
tracking nut as needed to center belt on drums.
• If belt moves to the left, turn tracking nut to the right, if belt
moves to the right, turn tracking nut to the left.
• Quickly turn switch ON and OFF again. If belt moves to one
side, continue adjusting tracking nut as needed to center
belt on drums.