Related Manuals for Craftsman 351.215132
Summary of Contents for Craftsman 351.215132
- Page 1 Operator's Manual ® 2 x 42" Belt 6" Disc SANDER Model No. 351.215132 Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. www.sears.com/craftsman 30635.00 Draft (04/01/09)
- Page 2 FULL WARRANTY when tired, intoxicated or when taking medications that cause drowsiness. CRAFTSMAN TOOL If this Craftsman tool fails due to a defect in material or PREPARE WORK AREA FOR JOB workmanship within one year from the date of pur- •...
- Page 3 KNOW HOW TO USE TOOL • Use right tool for job. Do not force tool or attachment to do a job for which it was not designed. • Disconnect tool when changing belt or abrasive disc. • Avoid accidental start-up. Make sure that the switch is in the "OFF"...
-
Page 4: Power Source
Tighten socket head bolt to secure belt table position. Properly Grounded Outlet ATTACH HORIZONTAL STOP Grounding Prong Refer to Figure 3. A horizontal stop bar with nut is provided as a positive 3-Prong Plug stop when using the sander with the belt housing adjusted to a horizontal position. -
Page 5: Specifications
DESCRIPTION Be sure motor runs clockwise on disc side. Abrasive Craftsman 2 x 6" Belt and Disc Sander has a 2" x 42" belt must travel down. belt and 6" disc for deburring, beveling and sanding... - Page 6 Remove belt cover. Avoid kickback by sanding in accordance with the directional arrows. Loosen and remove socket head bolt from bracket. Keep your hands clear of abrasive belt, disc and all Remove bracket. moving parts. Loosen socket head bolt and move belt table parallel For optimum performance, do not stall motor or to belt.
-
Page 7: Contour Sanding
• Replace belt cover and knobs. isting Bolt Locking Move the workpiece against belt. Belt will follow contour. SHARPENING Refer to Figure 10. • Adjust belt table to desired sharpening angle and tighten securely. Use belt sander to notch the back of an auxiliary piece of wood. - Page 8 USING MITER GAUGE • Use the work stop to position and stabilize work- piece Keep end butted against work stop and move Refer to Figure 14 workpiece evenly across abrasive belt • The miter gauge is used only on the disc table Use the miter gauge for securing work and holding the proper angle while disc sanding •...
- Page 9 CORRECTIVE ACTION SYMPTOM POSSIBLE CAUSE(S) Motor will not start 1. Low voltage 1. Check power line for proper voltage 2. Open circuit in motor or 2. Inspect all lead connections on motor loose connections for loose or open connection 3. Defective switch 3.
- Page 10 Model 351.21 5132 Figure 14 - Replacement Parts Illustration for Sander...
- Page 11 PART NO. DESCRIPTION PART NO. DESCRIPTION QTY. QTY. 30638.00 STD870408 4-0.7 x 8mm Socket Head Bolt* Motor Assembly Line Cord 24704.00 Disc Guard 00067.00 30639.00 Strain Relief STD870620 6-1.0 x 20mm Socket Head Bolt* STD863508 5-0.8 x 8mm Pan Head Screw* STD870510 5-0.8 x 10mm Socket Head Bolt* 5mm Lock Washer*...
- Page 12 _trea limpia. Las _.reas de trabajo desordenadas atraen accidentes. GARANTIA COMPLETA DE UN ANO PARA • No use herramientas mec_.nicas en ambientes peligrosos. HERRAMIENTA CRAFTSMAN use herramientas mec_tnicas en lugares hQmedos o mojados. Siesta herramienta Craftsman fallara por causa de defectos...
- Page 13 • Revise para verificar si hay partes daSadas. Revise para La bolsa de partes incluyes: barra de tope horizontal, tope fun- verificar el alineamiento de las partes movibles, si hay atas- cional, dos manillas, dos indicadores, un perno de cabeza hueca camiento, roturas y montaje o cualquier...
- Page 14 INSTALACION DE LA MESA DE LA CORREA • Si las instrucciones para la conexi6n a tierra no se entienden o si se tienen dudas de que la herramienta est6 conectada Refierase a la Figura 3. tierra correctamente, consulte a un electricista calificado.
-
Page 15: Cordones De Extension
DESCRIPClON mente o un sistema de cables conectado a tierra correctamente. La lijadora de correa y disco de 2 x 6", Craftsman, cuenta con • Muchos de los tornillos de la plancha de cubierta, las tube- una correa de 2 x 42"... - Page 16 CAMBIO DE LA CORREA ABRASIVA • Siempre use protecci6n para los ojos o la cara. • AsegQrese que la correa abrasiva est6 alineada en forma Refierase alas Figuras 6 y 7. correcta. El alineamiento correcto le entrega el rendimiento ADVERTENOIA: Desconecte la lijadora de la fuente de energia...
- Page 17 Asegure la posicidn cuando la correa est6 con la alineacidn correcta de modo que permanezca centrada en las ruedas. Mantenga la posici6n del perno de cabeza hueca con la Ilave hexagonal de 4 mm. Apriete la tuerca de fijacidn para fijar la posicidn del perno.
- Page 18 • Use una escuadra de combinacidn para ajustar el tope de tra- • Mueva la pieza de trabajo a trav6s del lado de abajo (dere- bajo a 90 ° con respecto a la correa, con espacio libre de 1/ld' cho) del disco abrasivo. El disco abrasivo se mueve de forma entre la correa y el tope de trabajo.
- Page 19 SINTOMA MEDIDA CORRECTIVA CAUSA(S) POSIBLE(S) El motor no arranca 1. Voltaje bajo 1. Revise la energia para ver si tiene el voltaje apropiado Hay un circuito abierto en el motor 2. Inspeccione todas las conexiones de entrada en el o hay conexiones sueltas motor para verificar si hay alguna suelta o abierta Interruptor defectuoso 3.
- Page 20 Your Home For expert troubleshooting and home solutions advice: www.managemyhome.com For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories owner's manuals that you need to do-it-yourself.