Table of Contents
Advertisement
RULES FOR SAFE OPERATION
(Continued)
I
I
I
I
NEVER USE IN AN EXPLOSNE ATMO-
SPHERE. Normal sparking of the motorcould
igniteflammable liquids,gases, or fumes,
KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Always use a clean
clothwhen cleaning. Never use brake fluids,
gasoline, petroleum-based productsor any
strongsotventsto clean your tool.
STAY ALERT, Watch what you are doing and
use common sense. Do not operate toolwhen
you are tired. Do not rush.
CHECK DAMAGED PARTS. Beforefurther use
of the tool, a guard or other part that isdamaged
shouldbe carefully checked to determine that it
willoperate properly and perform its intended
function. Check for alignment of moving parts,
bindingof moving parts, breakage of parts,
mounting,and any other conditionsthat may
affect its operation. A guard or other part that is
damaged should be properly repaired or
replaced by an authorized service center unless
indicatedelsewhere in this instructionmanual.
I
DO NOT USE TOOL IF _NI'I'CH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by an authorized service center.
DRUGS, ALCOHOL, MEDICATION, Do not
operate tool while under the influenceof drugs,
alcohol, or any medication.
DRILLING OR DRIVING SCREWS INTO
ELECTRICAL WIRING IN WALLS, CEILINGS,
OR OTHER AREAS CAN CAUSE THE BIT OR
CHUCK TO BECOME ELECTRICALLY LIVE.
Do not touch metal parts when drillingintoa wall;
grasp onlythe insulated handle(s) or plastic
housingwhen using this tool. Make sure hidden
electrical wiring, water pipes, and mechanical
hazards are not in the path of the bit when
drillinginto a wall,
•
INSPECT FOR and remove all nails from lumber
before ddUing.
IMPORTANT
SAFETY RULES FOR BATTERY
TOOLS
Battery tools do not have to be plugged into an
electrical outlet;therefore, they are always in
operating condition.Be aware of possible
hazards when not using your battery tool or
when changing accessories.
USE ONLY THE CHARGER PROVIDED WITH
YOUR BATTERY TOOL. Do not substituteany
other charger. Use of another charger could
cause batteries to explode causing possible
serious injury.
DO NOT PLACE BATTERY TOOLS OR THEIR
BA'I-FERIES NEAR FIRE OR HEAT. They may
explode.
DO NOT CHARGE BATrERY TOOL IN A
DAMP OR WET LOCATION.
Your battery tool shouldbe charged in a location
where the temperature is more than 50°F bLt
less than 100°F.
Under extreme usage or temperature conditions,
batten/leakage may occur, If liquidcomes in
contact with your skin,wash immediately with
soap and water, then neutralize with lemonjuice
or vinegar. If liquidgets in your eyes, flush them
with clean water for at least 1O minutes,then
seek immediate medical attention.
If canying your battery tool at your side, make
sure it is not runningand your finger is not on the
switch.Avoid accidental starting,
SECURE WORK before applying power. NEVER
hold workplace in your hand or across your legs.
WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS,
IMPORTANT
SAFETY INSTRUCTIONS
FOR
CHARGER
•
SAVE THESE INSTRUCTIONS. This manual
contains importantsafety and operating
instructionsfor batter/charger part number
982245-001.
Before using battery charger, read all instructions
and cautionarymarkings in this manual, on
battery charger, and product using battery
charger.
A
WARNING:
To reduce dskof injury,charge only
nickel-cadmiumtype rechargeable bettedes.
Other typas of batteries may burstcausing
personal Injuryand damage.
I
I
Do not expose cherger to rain or snow.
Use of an attachment not recommended or sold
by the battery charger manufacturer may result
in a risk of fire, electric shock,or injuryto
parsons.
To reduce dsk of damage to charger body and
cord, pull by charger body rather than cord when
disconnecting charger,
Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected
to damage or stress,
Advertisement
Table of Contents
