Advertisement
Quick Links
Operator's Manual
iPRO
FESSiO
HAL
i
PROFESSIONAL
1/2 in., 14.4 VOLTS CORDLESS DRILL-DRIVER
Variable Speed / Reversible
Model No.
315.267380
Save this manual for
future reference
CAUTION:
Read and
follow all Safety Rules and
Operating Instructionsbefore
first use of this product.
Customer
Help Line: 1-800-932-3188
Sears,
Roebuck
and Co., 3333
Beverly
Rd., Hoffman
Estates,
IL 60179
USA
Visit the Craftsman web page: www.sears.com/craftsman
983000-186
04-03
• Safety
• Features
• Assembly
• Operation
•, Maintenance
• Parts List
0( us
Advertisement
Related Manuals for Craftsman 315.267380
Summary of Contents for Craftsman 315.267380
- Page 1 Safety Rules and •, Maintenance Operating Instructionsbefore • Parts List first use of this product. Customer Help Line: 1-800-932-3188 Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 0( us Visit the Craftsman web page: www.sears.com/craftsman 983000-186 04-03...
- Page 2 • Exploded View and Repair Parts List ........................... • Parts Ordering / Service ............................... FULL ONE YEAR WARRANTY ON CRAFTSMAN PROFESSIONAL CORDLESS DRILL-DRIVER rRAFTSMAN If this Professional Cordless Drill-Driver fails due to a defect in material or workmanship within one year from the date of purchase, Sears will repair it, free of charge.
- Page 3 Yourdrill-driver hasmanyfeatures formaking yourdrilling CAUTION: Carefully read through this entire operations m orepleasant andenjoyable. Safety, operator's manual before using your new drill-driver. performance anddependability havebeen giventop Pay close attention to the Specific Safety Rules / priority inthedesignofthisdrill-driver making iteasyto Symbols, Warnings and Cautions. If you use your maintain andoperate.
- Page 4 Tool Use and Care • Use clamps or other practical way to secure and • Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools, with sharp support the workpiece to a stable platform. Holding cutting edges are less likely to bind and are easier to the work by hand or against your body is unstable and control.
- Page 5 • Neverusea batterythat hasbeendroppedor • Do not operate charger with a damaged cord or receiveda sharpblow. A damaged battery is subject plug. If damaged, have replaced immediately by a qualified serviceman. Following this rule will reduce the to explosion. Properly dispose of a dropped battery immediately.
- Page 6 Important: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. SYMBOL NAME EXPLANATION Volts Voltage Amperes Current Hertz Frequency (cycles per second)
-
Page 7: Specifications
PRODUCT SPECIFICATIONS: CHARGER DRILL-DRIVER 315.267380 Item No. 9 11040 (981399-001) Chuck 1/2 in. Keyless Input 120 V, 60 Hz, AC only Motor DC Motor 14.4 Volt 9.6 - 24 Volt Charging Voltage Gear Train Two Speed t Hour Charge Rate Switch Variable Speed BATTERY... - Page 8 YELLOWLIGHT"ON" ANDRED TORQUE LIGHTFLASHINGINDICATES ADJUSTMENTRING DEFECTIVEBATTERYPACK CHARGER ) SPEED GEARTRAIN(HI-LO) DIRECTION OF ROTATION SELECTOR (FORWARD/REVERSE) KEYLESS CHUCK REDLIGHT"ON" INDICATES FASTCHARGING MODE GREENLIGHT"ON" INDICATESFULLY CHARGEDANDSLOWCHARGING TO MAINTAINBATTERYPACK SCREWDRIVER BITS BATI'ERYPACK WRISTSTRAP Fig. 1 CHARGER See Figure 2. Your charger has a "key hole" hanging feature for convenient, space saving storage. Screws should be installed so that center distances are 4-1/8 inches apart.
- Page 9 AUTO-SPINDLE LOCK ,_WARNING: Make sure to insert drill bit straight into chuck jaws. Do not insert drill bit into chuck jaws at Your cordless drill has an auto-spindle lock. This feature an angle and then tighten, as shown in Figure 4. This makes installing and removing bits much easier.
- Page 10 TO A'I-rACH BAI-I'ERY PACK TO DRILL TO REMOVE BA'I-FERY PACK FROM DRILL See Figure See Figure 5. • Lock the switch trigger by placing the direction of Note: Battery pack is shipped in a low charge condition. rotation selector in center position. See Figure 10. Therefore, it must be charged prior to use.
- Page 11 If after one hour red light is still flashing, this indicates a WARNING: Always wear safety goggles or safety defective battery pack and should be replaced. glasses with side shields when operating tools. Failure to do so could result in objects being thrown Green light on indicates battery pack is fully charged into your eyes, resulting in possible serious injury.
- Page 12 SWITCH LOCK SWITCH See Figure 10. See Figure 8. The switch trigger can be locked in the OFF position. This TO turn your drill ON, depress the switch trigger. To turn it feature can be used to prevent the possibility of accidental OFF, release the switch trigger.
- Page 13 ADJUSTABLE TORQUE CLUTCH KEYLESS CHUCK See Figure 11. Your drill is equipped with an adjustable torque clutch for driving different types of screws into different materials. A keyless chuck has been provided with your drill to allow The proper setting depends on the type of material and for easy installation and removat of bits.
- Page 14 When drilling hard smooth surfaces use a center punch to WARNING: Always wear safety goggles or safety mark desired hole location. This will prevent the drill bit glasses with side shields when operating tools. from slipping off center as the hole is started. However, Failure to do so could result in objects being thrown the low speed feature allows starting holes without center into your eyes, resulting in possible serious injury.
- Page 15 Insert hex key in chuck and tighten chuck jaws CHUCK REMOVAL securely. Tap sharply with a mallet in a counterclock- See Figures 14, 15, and 16. wise direction. This will loosen chuck on the spindle. It The chuck must be removed in order to use some can now be unscrewed by hand.
- Page 16 Do not abuse power tools. Abusive practices can WARNING: When servicing use only identical Craftsman replacement parts. Use of any other damage tool as well as workpiece. parts may create a hazard or cause product damage. Only the parts shown on parts list, page 17, are intended to be repaired or replaced by the customer.
- Page 17 NO. 315,267380 The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your CRAFTSMAN 1/2 in, PROFESSIONAL CORDLESS DRILL-DRIVER or when ordering repair parts. SEE BACK PAGE FOR PARTS...
- Page 18 Your Home For repair-in your home-of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it! For the replacement parts, accessories owner's manuals that you need to do-it-yourself. For Sears professional installation of home appliances...