Related Manuals for Frigidaire FRA08PZU110
Summary of Contents for Frigidaire FRA08PZU110
- Page 1 FRIGIDAIRE iii_i_i`_`iiii_i_i_ii(iiiiiii_iiiiiiiiii!i_`_`_i1iiiiij1iiiiiiiiiiI!_iiiiiii_i1ii_iiiiiiiiiiiii_iiii_fiiiiiii Pro( Air Conditioner Featu...
- Page 2 This USE & CARE MANUAL provides specific operating instructions for your model. Use the room air conditioner only as instructed in this USE & CARE MANUAL. These instructions are not meant to cover every possible condition and situation that may occur. Common sense and caution must be practiced...
-
Page 3: Operation Of Current Device
CAUTION. I Avoid Injury or damage to the unit or other property Provide occasional ventilation during use. Do not direct airflow at fireplaces or other heat related sources as this could cause flare ups or make units run excessively. Do not climb on or place objects on outdoor... -
Page 4: Product Registration
Record in the space provided below the model and serial numbers. On all models, the serial plate is located on the outside of the cabinet. Register Your Product The self-addressed PRODUCT REGISTRATION CARD should be filled in completely, signed and returned to the Frigidaire Company. Packaging Remove all packaging from inside the carton,... -
Page 5: Air Conditioner
© © Battery Size: AAA sleep Umer Warning: Do not mix old and new batteries. Do not mix heat alkaline, standard (carbon-zinc), or rechargeable (nickel- FRIGIDAIRE FRIGIDAIRE cadmium) batteries. STANDARD REMOTE FOR HEAT MODELS w/DISPLAY & REMOTE SENSING BUTTON Operating Instructions The following instructions represent the Touch Pad, the same instructions can be used for the Remote Control. - Page 6 Operating Instructions (continued) TO CHANGE TEMPERATURE SETTING: YOU WILL SEE; temp/timer temp/timer remote remote filter hi [] fitter reed hi [] sensing reed sensing reset auto reset auto sleep ON-OFF FAN SPEED sleep ON-OFF FAN SPEED Note: Tap or hold either up ( A ) or down ( V ) button until the desired temperature is seen on the display.
- Page 7 Operating Instructions (continued) TO OPERATE ON FAN ONLY; YOU WILL SEE= ternp/timer dean cool dean [] cool remote remote econ sensing econ sensing heat terns/time heat fan only [] fan only timer MODE ON-OFF timer MODE ON=OFF Note: Use this function only when cooling is not desired, DO THIS;...
- Page 8 Operating Instructions (continued) YOU WILL SEE HOW MUCH TIME IS CHOSEN: TIMER: DELAY STOP / START FEATURE temp/timer temp/timer remote dean [] cool dear [] cool remote econ econ sensing sensing heat heat fan on_ fan only timer MODE ON=OFF timer MODE ON=OFF...
- Page 9 FAULT CODES: tamp/timer tamp/timer tamp/timer tamp/timer tamp/timer ON-OFF ON-OFF ON-OFF ON-OFF If the display reads "HS", "AS", "ES", "CS" or "OS", a sensor has failed. Contact your Authorized Frigidaire Service Center. @2009 Electrolux Home Products, Inc. All rights reserved,...
- Page 10 Operating Instructions (continued) TO CHANGE TEMPERATURE DISPLAY; YOU WILL SEE: temp/timer temp/timer remote remote fitter hi , fitter hi , reed sensing sensing auto auto reset reset 0N-0FF FAN SPEED sleep 0N-0FF FAN SPEED steep Note: The control is capable of displaying temperature THIS: degrees Fahrenheit or degrees Celsius.
-
Page 11: Care And Cleaning
Operating Instructions Air Directional Louvers (continued) AUGER WHEELS Air directional louvers control air flow direction. Your air conditioner has the louver type described below. Auger Type The louvers will allow you to direct the air flow Up or Down and Left or Right throughout the room as needed. - Page 12 Room too cold. Set temperature too low. Increase set temperature. Remote Sensing activated (on some models) and remote control located in Hot Spot - Relocate remote control or deactivate remote sensing. If These Solutions Fail, Call 1=800-944=9044 For Frigidaire Service,...
- Page 13 Your appliance is covered by a limited one-year warranty and a limited 2-5 year warranty on the sealed system (the compressor, condenser, evaporator and tubing). For one year from your original date of purchase, Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or workmanship when such appliance is installed, used and maintained in accordance with the provided instructions.