Advertisement
About the Ceramic
Glass Cooktop
The ceramic cooktop has radiant surface elements located below the surface of the glass. The design of the ceramic
cooktop outlines the area of the surface element underneath. Be sure to match the pan size with the diameter of the
element outline on the cooktop. Heat is transferred up through the surface of the cooktop to the cookware. Only flat-
bottomed cookware should be used.
The type and size of cookware, the number of surface elements in use and their settings, are all factors that will affect the
amount of heat that will spread to areas beyond the surface elements. The areas surrounding the elements may become
hot enough to cause burns.
@
OFF
hi
10
\
IO
sire
2
3
®
o
®
@
Small
Large
OFF
Element
OFF
Element
hi
hi
hi
000
Warming
0
@
Zone
Warming
Zone
Surface
Control
(some models)
8
7
About the Radiant Surface
Elements
The element temperature rises gradually and
evenly. As the temperature rises, the element will
glow red. To maintain the selected setting, the
element will cycle ON and OFF. The heating
element retains enough heat to provide a uniform
and consistent heat during the off cycle.
4
6
reed
OOO
Right
COO
Right
O
@ Rear
O
_)
Front
Single
Radiant
Surface
Control
(some models)
Single
Radiant (some models)
Dual Radiant
(some models)
Surface
Control
For efficient cooking, turn OFF the element several
minutes before cooking is complete. This will allow
residual heat to complete the cooking process.
NOTE: Please read detailed instructions for
ceramic glass cooktop cleaning in the General
Care & Cleaning
and Before You Call checklist
sections of this Use & Care Manual.
Io
sire
3
4
reed
Hot Surta_
l
G/_L_IATOR
LIGHTI
hi
Element
On & Hot Surface Indicator
Lights
Your range is equipped with two different types of radiant surface control
indicator lights that will glow on your range-- the Element On indicator
light and the Hot Surface indicator lights (See illustration at left).
8
7
The Element On indicator
lights are located on the control panel above each radiant
element control knob and will glow when a surface element is turned ON. A quick glance
at this indicator light after cooking is an easy check to be sure ALL surface controls are
turned OFF. The Hot Surface indicator light located on the control panel will glow when
any surface cooking area heats up and will REMAIN ON until the glass cooktop has
cooled to a MODERATE level.
Left OOO
Rear O
@
Cookware
Material Types
NOTE: Radiant elements have a limiter that allows the element to cycle ON and OFF,
even at the HI setting. This helps to prevent damage to the ceramic smoothtop. Cycling at
the HI setting is normal and will occur more often if the cookware
is too small for the
radiant element or if the cookware bottom is not flat.
The cookware material determines how evenly and quickly heat is transferred from the surface element to the pan bottom.
The most popular materials available are:
ALUMINUM - Excellent heat conductor. Some types of food
will cause it to darken (Anodized aluminum cookware resists
staining & pitting), tfaluminum pans slide across the ceramic
cooktop, they may leave metal marks which will resemble
scratches. Remove these marks immediately.
COPPER - Excellent heat conductor
but discolors easily.
May leave metal marks on ceramic glass (see Aluminum).
STAINLESS STEEL - Slow heat conductor with uneven
cooking results. Is durable, easy to clean and resists
staining.
CAST IRON - A poor heat conductor however will retain
heat very well. Cooks evenly once cooking temperature is
reached. Not recommended for use on ceramic cooktops.
PORCELAIN-ENAMEL
on METAL- Heating
characteristics will vary depending on base material.
Porcelain-enamel
coating must be smooth to avoid
scratching ceramic cooktops.
GLASS - Slow heat conductor. Not recommended for
ceramic cooktop surfaces because it may scratch the
glass.
Hide quick links:
Advertisement
