Frigidaire FPCS3085LFA Use & Care Manual page 42

Before you call for service, review this list. It may save you time and expense. The list includes common
occurrences that are not the result of defective workmanship or materials in this appliance.
Range is not level. Poor installation. Place oven rack in center of oven. Place a level on the oven rack. Adjust
leveling legs at base of range until the rack is level. When range is level, cooktop may
......... appear out of alignment if countertop is not level. ............................................................................................
Weak, unstable floor, Be sure floor is level and can adequately support range. If floor is
.... sagging or slopping, contact a carpenter to correct the situation.
Kitchen cabinet misalignment may make range appear to be unlevel. Be sure cabinets are
square and have sufficient room for range clearance.
Cannot move Cabinets not square or are bui!t in too tight. Contact a cab!net maker to correct the problem.
appliance easily. Contact builder or installer to make appliance accessible.
Appliance
must .....
Caipetinterferes with range Proviae sufficient space so range can Gel fred over carpet .....................
be accessible for
service, line
ishard:pium6eal Ha ea
flexibie CISIA internationai approved metai appliance
connector installed.
Entire range or oven Make sure cord/plug is plugged tightly into outlet. ........................................................................................
does not operate, Service wiring is not complete. Call an authorized servicer. ...............................
Electrical power outage. Check house lights to be sure. Call your local electric company for
service,
CooktoP control An error at power up ior after a power faiiurei if ANY
ii
displays any E code of the surface control knobs were left in the ON positions (Figure 8). If a power failure should
error (ex.-" E014) occur, be sure to set all of the surface control knobs to the OFF position. This will reset the
surface controls.
Also, if the induction sensors cannot detect a pan made of the correct material or if the pan is
not centered properly or if the pan is too small, the power level will flash in the in the digital
display and the pan will not heat. After 3 minutes, an "Er" error code will be displayed until the
controls are set to OFE
Oven control beeps
and displays any F
code error (ex.: Fl!)
Oven light does not
work.
If the surface controls do not function and the "ER" message remains in any display after following
..... these procedures, contact your authorized servicer for assistance. .........
Cooktop control has detected a fault or error condition. Try turning electrical power supply
OFF and back ON to the appliance in order to reset main controls. If fault recurs, record fault
.......................... number and unplug the appliance. ................................
Electronic control has detected a fault condition. Press CANCEL to clear the display and
stop beeping. Reprogram oven. If fault recurs, record fault number. Press CANCEL and call
.... an authorized servicer for assistance. ...............................................................
..... Replace or tighten bulb. See Changing Oven Light section in this Use & Care Guide. ..........
Electrical power outage. Check house lights to be sure. Ca!! your local electric company for semite.
Surface unit does No power to the appliance. Check steps under "Entire Range or Oven Does Not Operate" in
not heat. this Before you Call checklist.
No cookware was placed on the induction cooking zones or the cookware material type is
.... !ncorrect for induction cooking. ....................................................
..... Incorrect control setting. Make sure the correct control is on for the surface unit to be used.
Surface units too Incorrect control setting, Make sure the correct control is on for the surface unit to be used. :
hot or not hot Lightweight or warped pans used. Use only fiat, evenly balanced, medium or heavyweight
enough, cookware. Flat pans heat better than warped pans. Cookware materials and weight of the
material affect heating. Heavy-and medium- weight pans heat evenly. Because lightweight
Drip bowls are Foods with acids, such as tomatoes, if allowed to stand in/on bowls will cause corrosion.
pitting or rusting, Remove and wash drip bowls as soon as poss!ble after spillover. .....................
Normal environment. Houses along sea coast are exposed to salt air. Protect bowls as much
as possible from direct exposure to salt air.