Advertisement
• Knowyourtool.Learn the tool'soperation, applica-
tionandspecificlimitations.
• Userecommended accessories ( refer to page13).
Useof improper a ccessories m aycauseriskof
injurytopersons.
• Handle workpiece correctly. Secure workwith
clampsor vise.Leave handsfreeto operate
machine. Protecthands frompossible injury.
• Feedworkintoa bit or cutteragainst t hedirection of
rotation of bitor cutter.
•
Turn machine off if it jams. A cutter jams when it digs
too deeply into the workpiece. (The motor force
keeps it stuck in workpiece.)
CAUTION:
Think safety! Safety is a combination of
operator common sense and alertness at all times
when tool is being used.
WARNING:
De not attempt to operate tool until it is
completely assembled according to the instructions.
Refer to Figures 4 and 6.
CAUTION:
Be careful not to touch overhead power
lines, piping, lighting, etc., if lifting equipment is used.
Drill press weighs approximately 450 Ibs. Proper tools,
equipment and qualified personnel should be employed
in all phases of unpacking and installation.
Crates should be handled with care to avoid damage
from dropping, bumping, etc. Store and unpack crates
with correct side up. After uncrating drill press, inspect
carefully for any damage that may have occurred, dur-
ing transit. Check for loose, missing or damaged parts.
If any damage or loss has occurred, claim must be filed
with carrier immediately. Check for completeness.
Immediately
report missing parts to dealer.
Drill press is shipped assembled, except for the drill
chuck with key, arbor and guard.
IMPORTANT: The tool has been coated with a protec-
tive coating. In order to ensure proper fit and operation,
the coating must be removed. Remove coating with mild
solvents, such as mineral spirits and a soft cloth.
Nonflammable
solvents are recommended.
After clean-
ing, cover all exposed surfaces with a light coating of
oil. Paste wax is recommended
for table top.
NOTE: Never use highly volatile solvents. Avoid getting
cleaning solution on paint as it may tend to deteriorate
these finishes. Use soap and water on painted compo-
nents.
Refer to Figures 4, 6 and 7.
MOUNT
DRILL
CHUCK
AND
ARBOR
•
Be sure spindle taper, arbor taper and chuck taper
are clean and dry.
•
Insert arbor into spindle, push arbor into spindle and
twist arbor slightly to release air trapped in taper.
•
Mount chuck onto arbor, push chuck over arbor and
twist arbor slightly to release air trapped in taper.
•
Be sure chuck and arbor are securely mounted.
MOUNT
DRILL PRESS
GUARD
Refer to Figure 4.
Place clamp opening over bottom of drill press quill and
secure by tightening socket head bolt at rear of clamp
(Key. No. 1).
CAUTION:
The operation of any power tool can result
in foreign objects being thrown into the eyes, which can
result in severe eye damage. Always wear safety glass-
es complying with United States ANSI Z87.1 (shown on
package) before commencing
power tool operation.
Safety glasses are available through your Grainger cat-
alog.
TABLE
CRANK
Refer to Figure 7.
•
Remove handle from inside of crank arm.
• Thread handle onto outside of crank arm (Key. Nos.
15 and 16).
MOUNT
DRILL PRESS
•
Drill press must be mounted to flat level surface. Use
shims or machine mounts if necessary. Do not
mount drill press in direct sunlight.
•
Be sure to bolt drill press to floor securely to prevent
tipping and minimize vibration.
• Tighten all nuts and bolts that may have loosened
during shipment.
POWER
SOURCE
WARNING:
Do not connect drill press to the power
source until all assembly steps have been completed.
The motor is designed for operation on the voltage and
frequency specified. Normal loads will be handled safe-
ly on voltages not more than 10% above or below spec-
ified voltage. Running the unit on voltages which are not
within range may cause overheating and motor burn-
out. Heavy loads require that voltage at motor terminals
be no tess than the voltage specified on nameplate,
•
Drill press requires a 115/230 volt, 60 Hz power
source.
To use the drill press with a 230V power supply,
have a qualified electrician attach a 230 volt, 20/30A
three-prong
plug (not supplied) onto drill press line
cord.
•
Power supply to the motor is controlled by a rotary
switch.
3
Advertisement
