Table of Contents
Advertisement
due to e_ther a power interruption
or the saw
has been unplugged.
FLASHING
"E"
INDICATES
CALIBRATION
REQUIRED
TO LOCK
4. CONTROL
KEYS:
The two rows of keys directly
under
the display
are the control
keys. They
are how you tell the
computer
what you want
it to do.
MINUS
A. Jog
key
is a rocker
type
switch
that
when
pushed
up and
held
in causes
the blade
to
elevate
when
in
L_L____Jor to bevel to the left
when in
_
.The motionsaretheopposite
when
the key is pushed
down.
When
the jog key is pressed
and immediately
released
it will
cause
the
blade
to change
elevation
by 0.005" or bevel by 0.1 ° depending
on the function
selected.
This "tapping"
of the
jog
key
can
be repeated
as many
times
as
desired
to move blade
into
position.
B. [_
and
_-_
keys are used to select the
desired
function.
Pressing
_
will
display
current
blade
elevation.
Saw
must
be in elevation
mode
before
any programmed
or jogging
elevation
operation
can be performed.
A lighted
decimatabove
_
keyindicatesthatthe
elevation
function
is active.
F-----q
In the same way, pressing
_
will display
the current
angle
of the blade
and allow
any
programmed
or jogging
bevel operation
to be
performed.
A lighted
decimal
above
indicates
that the bevel
mode is active.
C. _
key is a dual
purpose
key. When the
saw is first
plugged
in or if there
has been a
power
interruption
the
key
operates
as a
"Calibration"
key. Pressing
the key, with the
g.
E.
F.
blade at 90 ° to the table and at zero elevation
accurately
sets the
program
that
computes
the elevatmon
and
bevel
angle
of the blade
Once
the calibration
has been
set the key
becomes
an "Enter"
key
used
for entering
both
a bevel
and an elevation
programmed
motion.
r
The
_
key, when
pressed,
will start
a
programmed
moben.
It becomes
reactive
while
the saw motor
is
"ON".
The
_
key will set the display
to a "zero"
point
other
than
at the
table
top,
or when
using
a cutting
tool
less than
10 inches
tn
diameter.
See
"Calibrating
the
Saw
for
Electronic
Operations"
Page 29.
The
_
key will clear
the display
if an
error is made m a programmed
entry and will
return
the display
to the current
posmtion
of
the chosen
function.
This key will also stop a
programmed
motion
once
begun
and
clear
the original
destination.
5. NUMBER
KEYS:
DNm-q
=
These
keys
include
the number
keys
through
_
, the decimal
point
_
and
keys. The number
keys are used to enter
a destination
for
programmed
motion.
The
decimal
point
is used when entering
the decimal
part of the number
The
[__
key is pressed
afterthe
numbersare
entered
if a destination
is desired
below
the
"zero"
location.
A lighted
dot in the upper
left hand corner
of the
display
indicates
"minus."
RIP FENCE...
is locked in place by pushing the
lock lever down. To move fence, lift up on the lock
lever and grasp the fence with one hand at the
front.
Holes are provided
in the rip fence for attaching
a
wood
facing
when
using
the
dado
head,
or
molding
head.
25
Advertisement
Table of Contents
