GE 23 Owner's Manual And Installation page 5

About the temperaturecontrols.
Not aft features are on all models. Your controls will look like one of the foflowing:
Non-LCD models LCDmodels
NOTE:Therefrigerator is shipped with protective film coveringthe temperature controls,If this film was not
removed during installation, removeit now,
ge.com
Thetemperature controls arepresetin thefactoryat37°F (3°¢)for the
refrigerator compartment and0_ (-18°C) f orthefreezer compartment
Allow24hoursforthetemperature t o stabilize tothepreset
recommended s ettings,
Refrigerator temperatures c anbeadjusted between 34°F and44°F
(I°C to 7°C), andthefreezer temperatures c anbe adjusted between
-6°F and+6°F(-21°C to -14°C).
Tochange the Refrigerator temperature:
LCD Models:
Access By: Horn e > RefiJgerator
Activate By: Using tile arrows to select tile desired
temi)eramre. _4_u must press ENTERto set tile new
temperature.
Tochange the Freezer temperature:
Access By: Home > Freezer
Activate By: Using tile arrows to select tile desired
temperature. Y)u must press ENTER to set tile new
temi)erature.
Once tile desired temperature has been set, tile display will
return to tile NOMEscreen and show tile set temperatures
tmderneath the actual temperature display for several
seconds. Several ac!iusnnents may be required. Each time
you a(!iust tile controls, allow 24 hom_ fin" tile refl_igerator
to reach tile temperature you have set.
Non-LCD Models:
To change tile temperature, press and release tile WARMER
or COLDERpad. Tile SETlight will come on and tile display
will show tile set temperature. To change tile temperature,
tap either tile WARMER or COLDER pad until tile desired
temperature is displayed.
Once the desired temperature has been set, tile
temperature display will return to tile actual refl'igerator
and fl'eezer temperatures alter 5 seconds. Several
a(!justinents ma)' be required. Each time you a(!iust tile
controls, allow 24 hom_ tot tile reli_igerator to reach tile
temperature you have set.
Thetemperature controls can display both the SETtemperature as weft
as the actual temperature in the refrigerator and freezer, Theactual
temperature may vary slightly from the SETtemperature based on
usage and operating environment
Turning the coolingsystemoff."
LCD models: Turning thecooling s ystemOFF stopscooling in boththe
freezerandrefrigerator compartments, butdoesnotshutoff electrical
powerto therefrigerator,
Non-LCD m odels: Setting eitheror bothcontrols to OFF stopscooling in
boththefreezer andrefrigerator compartments, butdoesnotshutoff
electrical p owerto therefrigerator,
LCDModels:
AccessBy:Home > Options > ]nfimnation
and Settings >
Cooling System
Ott
To ttlrn tile cooling s}:steln back on, press tile to/ich screen
and press the ON button.
ActivateBy:Pressing ENTER.
Non-LCD Models:
%q) tile WARMER pad fin" either
tile refligerator or tile
fl'eezer tmtil tile display shows OFF. To turn the unit back on,
press tile COLDERpad fin" either tile refl_igerator or fl'eezex:
Tile SETlight will ilhmfinate on tile side you selected. Then
press tile COLDERpad again (on tile side'where tile SET
light is ilhmfinated) and it will go to the preset points of 0°F
(-18°C) for tile ti'eezer and 37°F (3°C) fin" tile reli_igerator.
When tile unit is turned back on, it will take up to 94 horns
to stabilize.
Performance Air Flow System
Tile Perfommnce M>lqow System is designed to maximize
temperature control in tile reti_igerator and fl'eezer
compartments. This unique spedal feature consists of tile
Air Tower along tile back wall of tile refligerator and tile
Air Tunnel on tile bottom portion of tile ti'eezer rear wall.
Placing todd in ti'ont of tile lou\'e_s on these components
will not afti_ct i)erfimnance. Although tile Air Tower and
tile Air Tunnel can be removed, doing so will attect
temperature perfommnce. (l_%r remowfl instructions,
on-line, 24 horns a da_; contact us at ge.com or call
800.GE.CARES. In Canada, contact us at geappliances.ca
or call 1.800.361.3400.)
I
,,,><,,,,,,,,,,,,,,,,,,
ii!iiiiii_i_ii{i
i
w
7,
N"
i
H