Before Installation; Hardware And Software Requirements; Installation Environment And Installation Procedure - Sharp AR-P17 Software setupg guide Software Setup Manual

SAFETY STANDARDS
Warning
This is a Class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
This equipment complies with the requirements of Directive 89/336/EEC as amended by
93/6B/EEC
Dieses Gertit entspricht den Anforderungen del"EG-RichtJinie 891336/EWG mit Anderung
93/68/EWG.
Cc materiel repond aux exigences contenues dans la directive 89/336/CEE modifiee par la
directive
93IG8/CEE.
Dit apparaar voldoet aan de eisen van de richtlijn 89/336/EEG, gewijzigd door 93/68/EEG.
Dette udstyr overholder kruvene
i
direktiv nr. 89/336/EEC med tillteg or. 93/68/EEC.
Quest'apparecchio
e
conforme ai requisiti della direttiva 891336/EEC come emendata dalla
direttiva 93/68/EEC.
I-I EyKU1llcnacHl
nurn
nvrcncicpivarnt rmc rounrroe«; rmv OOllYWJV .11<; EupwnulK"t;;
Evcioru; 89/336/EOK, (mOOt;; 0
xcvovicuoc
aU16<; aUrLnA,llPcbSllKE ano 111V oOllyiu 93/68/EOK.
Este equipamento obedece as exigencies da directive 89/336/CEE na sua versac corrigida
pela directiva 93/68/CEE.
Este aparuto satisface las exigencias de la Directive 89/336/CEE, modificada par media de la
93/68/CEE.
Denna utrustning uppfyller kraven enligt riktlinjen 891336/EEC sa som kompletteras av
93/68/EEC
Dette produktet oppfyller betingelsene i direktivet 89/336/EEC i
endringen 93/68/EEC.
Tbma laite tayttaa direktiivin 89/3361EEC vaatimukset, jota on muutettu direktiivilla
93/68/EEC
The CE mark logo label is affixed on an equipment in case that the directives
described in the above sentence are applicable to the product. (This sentence is
not applicable in any country where the above directives are not required.)
Shielded cables must be used with this equipment to maintain compliance with
standards.
38
BEFORE INSTALLATION
HARDWARE AND SOFTWARE REQUIREMENTS
Check the following hardware and software requirements before installing the software.
Computer type
IBM PC/AT or compatible computer equipped with a USB 2.0/1.1'1, bi-directional
parallei interface (IEEE 1284), or 1OBase-T/1OOBase-TX LAN card
Operating system Windows 95'2, Windows 98, Windows Me,
Windows NT Workstation 4.0 (Service Pack 5 or laterr 3,
Windows 2000 Professional'S, Windows XP Protessional'v,
Windows XP Home Edition' 3
Other hardware requirements An environment that allows any of the above operating systems to fully operate
'1 Compatible with Windows 98, Windows Me, Windows 2000 Professional, Windows XP Professional or
Windows XP Home Edition preinstalled models equipped with a USB interface as standard.
'2 If you are installing the Printer Administration Utility in Windows 95, a system file must be updated before the
utility can be installed. For more information, click the "Display Readme" button in the Software Selection
window of the installer. (p.13)
'3 Administrator's rights are required to install the software using the installer.
INSTALLATION ENVIRONMENT AND
INSTALLATION PROCEDURE
Follow the appropriate installation procedure for your operating system and type of cable as indicated
below.
Cable
Operating system Procedure to follow
Windows 95/98/Me/
1. CONNECTING TO A NETWORK (p.a)
LAN
NT 4.0/2000/XP
2. SETTING THE IP ADDRESS OF THE MACHINE (p.5)
3. "INSTALLING THE PRINTER DRIVER (Standard installation)" (p.8)
USB
Windows 98/Me/2000
Installation in Windows 98/Me/2000 (USB cable) (p.16)
Windows XP
Installation in Windows XP (USB/parallel cable) (p.14)
Windows 95/98/Mel Installation in Windows 95/98/Me/NT 4.0/2000 (parallel cable)
Parallel
NT 4.0/2000
(p.18)
WindowsXP
Installation in Windows XP (USB/parallel cable) (p.14)
Printer sharing
Windows 95/98/Me/
SHARING THE PRINTER USING WINDOWS NETWORKING
NT 4.0/2000/XP (p.21)
3