Page 1
CD RECEIVER KD-SH1000 For canceling the display demonstration, see page 8. For installation and connections, refer to the separate manual. INSTRUCTIONS GET0366-003A [EX/EU]...
Page 2
IMPORTANT FOR LASER PRODUCTS CAUTION: CAUTION: How to reset your unit Warning: Caution on volume setting: • Your preset adjustments will also be erased. How to forcibly eject a disc Notice: • If this does not work, reset your unit. •...
Page 3
CONTENTS • Button operations are mainly explained with the illustrations in the table below. • Some related tips and notes are explained in “More about this unit” (see pages 34 – 38). Press briefly. Press repeatedly. Press either one. Press A, then Press and hold until your desired response begins.
Page 4
How to detach/attach the control How to enter the various menus panel Detaching... Select a menu you want. Time countdown indicator Attaching... Enter the selected menu. How to change the control panel Operate as instructed on the screen. angle When using the remote controller Caution:...
How to change the display information and patterns Ex.: When tuner is selected as the source Text information display for Source operation display FM RDS stations and DAB services Clock time display Large graphic display (full display size) Small graphic display Control panel Parts identification 1 BAND button...
Getting started Selects the source. ∞ • Changes the service. • Changes the Activates or deactivates crossover network folders. (see page 21) before turning on the power. • Basic operations – Pauses/stops or resumes playback with ∞. – Enters the main menu with 5. (Now 5/∞/4/¢...
To drop the volume in a Radio operations moment (ATT) To turn off the power Ÿ Start searching for a station. Selected band appears. Basic settings Enter the PSM menu (see page 4). To stop searching, To tune in to a station manually Canceling the display demonstrations Setting the clock...
Storing stations in memory To restore the stereo effect, FM station automatic presetting — SSM (Strong-station Sequential Memory) Tuning in to FM stations with strong Select the FM band (FM1 – FM3) you signals only—LO (local)/DX (Distance- want to store into. Extreme) Enter the MODE menu (see page 4).
Page 10
When using the remote controller When using the remote controller...
To deactivate the TA Standby Reception Store the setting. The TP indicator goes off. PTY Standby Reception To store other PTY codes into other PTY Standby Reception allows the unit to preset numbers. switch temporarily to your favorite PTY programme from any source other than AM. Repeat steps 2 to 5.
Tracing the same programme— Using the message service— Network-Tracking Reception RDS Radiotext (RT) What is RDS Radiotext Programme A broadcasting on different frequency areas (01 – 05) To show the RDS Radiotext (RT) information To change the Network-Tracking Reception setting, Automatic station selection—...
To go to the next or previous tracks Confirm the selection. To go to the next or previous folders (only for MP3/WMA/SD/USB) Select a disc/folder/file from the list. Current folder Ex.: When “Folder” is selected on step Starts playback. Other main functions Selecting a disc/folder/track on the list When using the remote controller Enter the MODE menu (see page 4).
Prohibiting disc ejection Intro Plays the beginning 15 seconds of... You can lock a disc in the loading slot. Track : All tracks of the current playback media. [ Folder* : First track of all folders of the current playback media. [ Disc* : First track of all the inserted discs.
To make more precise settings, Sound adjustments To cancel the acoustic effect, Ÿ Select a DSP mode. Select the number of the built-in speakers. Enter the DSP menu (see page 4). Ÿ Select one of the DSP modes. Select your listening seat position. To finish the procedure Select the speaker to be adjusted.
Page 19
Select the distance between the Finish the procedure. selected speaker and the seat. To change the measuring unit Repeat steps 4 and 5 to adjust the distance for the other speakers. Finish the procedure. Enter the EQ menu (see page 4). Select a sound mode.
Page 20
Select a band. Select a sound mode. Select a frequency band. Adjust the enhanced level for the selected band. Adjust the enhanced level for the selected frequency band. Select the frequency. Repeat steps 2 and 3 to adjust the other frequency bands. Select one of the user modes.
Page 21
To cancel Crossover, If you have installed the 3-way network speaker system in the car, make sure of the following: Enter the SEL menu (see page 4). Ÿ Select a setting item. * Appears only when crossover network is activated (see left column). While the power is turned off...
General settings — PSM You can change PSM (Preferred Setting Mode) Select or adjust the selected PSM item. items listed in the table that follows. Enter the PSM menu (see page 4). Select a PSM item. Repeat steps 2 and 3 to adjust the other PSM items if necessary.
Page 24
Indications Items Settings, [reference page] Dimmer Auto • Time Set • • • Bright 1 10 ID3 Tag • • Theme Large • Small • PTY Stby AF-Reg • AF Reg • • TA Vol 0 30 50 P-Search • •...
Page 25
Indications Items Settings, [reference page] Beep Ext In Changer Ext In Muting 1/ Muting 2 Amp Gain High PWR Low PWR Some characters or symbols will not be shown correctly (or will be blanked) on the display. Depends on the amplifier gain control. Displayed only when DAB tuner is connected.
Title assignment Selecting the graphic theme Select “Theme” from the PSM menu. Select the size of the display. Sources Maximum number of characters Select the theme. * You cannot assign names to any discs other than conventional CDs. Select the sources. Repeat steps 2 and 3 to select the other display size and theme.
Move to the next (or previous) iPod®/D. player operations character position. Repeat steps until you finish entering the title. Finish the procedure. Interface adapter for iPod D. player interface adapter To erase the entire title Caution: Available characters Preparations: Ÿ Continued on the next page...
Page 28
⁄ 5 ∞ 4 ¢ – – For iPod: Ô Ô Ô Ô Ô Ô For D. player: Ô Ô Ô Ô Ô ¢...
Select an item (see table below). Finish the procedure. Repeat play It is recommended to use DAB tuner KT-DB1000 with your unit. If you have another DAB tuner, consult your JVC IN-CAR ENTERTAINMENT dealer. Random play Ÿ Album* Song On Start searching for an ensemble.
Page 31
Store the service. Using the Standby Receptions TA (Road Traffic News) Standby Reception When using the remote controller PTY Standby Reception Tuning in to a preset DAB service Enter the MODE menu (see page 4). Select “List.” Announcement Standby Reception Select a preset number.
When shipped from the factory, Alternative Select an announce type. Frequency Reception is activated. To deactivate the Alternative Frequency Reception, see page 24. To show the Dynamic Label Segment (DLS) Finish the procedure. information • If the ANN indicator lights up, Announcement Standby Reception is activated.
Other external component Maintenance operations How to clean the connectors Connector Moisture condensation LINE-IN : EXT-IN : Ÿ Turn on the connected component How to handle discs and start playing the source. When removing a disc from Center holder its case, Adjust the volume.
Page 37
Sound adjustments Title assignment Selecting the DSP modes—DSP iPod® or D. player operations Storing your own sound modes Notice: Setting the sound modes—SEL For iPod users: For D. player users: General settings — PSM DAB tuner operations Continued on the next page...
Page 41
Symptoms Remedies/Causes • Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. • SD logo is a trademark. • Manufactured under license from BBE Sound, Inc. Licensed by BBE Sound, Inc. under USP5510752 and 5736897. BBE and BBE symbol are registered trademarks of BBE Sound, Inc.