Basic Settings - JVC RX-DV31SL Instructions Manual

Basic Settings
• Operating procedure
Ex.: When setting the digital input (DIGITAL IN) terminals.
Before you start, remember...
There is a time limit in doing the following steps.
If the setting is canceled before you finish, start from step !
again.
I Press SETTING.
The CONTROL buttons now work for basic settings. The
setting item selected previously appears on the display.
2 Press CONTROL • (or A) repeatedly until
"DGT (Digital)" (with the current setting)
appears on the display.
O_T_L _e
[] [] i",:"' T 'i i",i"::-- '-'":": :
i.._i.::i i .L i.._i:::,-, .L J L..i _ 15
3 Press CONTROL _ (or <) to select the
appropriate digital terminal setting.
• Each time you press the button, the indication changes
as follows:
O_T_L =Ule
[] [] ,,, ,,, ,m • ,,, ,,,, m m ,,,,,, •
I%1 • | '1 I%1 II • | I I I
iJ i.::i i .L iJ i:::= .3 ." i :_: _ 15
4 Repeat steps 2 and 3 to set other items if
necessary.
• For details about each item, see below.
• Speaker information
To obtain the best possible effect from the Surround modes
(see pages 28 to 31), register the following information after
all connections are completed.
• If you have used Quick Setup (see page 21), this setting is
not required.
• For subwoofer--"SUBWFR"
0_t_L _
S=KI
[] [] ...............
'-.I""" " " i i'-I
15
,,=p ',,,' i_' ",%, I I ',
Select one of the following settings:
YES Select when a subwoofer is connected.
NO Select when no subwoofer is used (initial
setting).
Note:
• If you have selected "NO"for the subwoofer, you can only select
"LRG (large)" for the front speakers,
• For front speakers--"FRNT SP"
_c_zAuyo
sPKt
[] [] p,, i,,,= i I ,,i,, ,,,. i,,,, ,, I i,='= ,,,,,
i" i":: . r'.ii ::::, i"' ;; L K i.::i _ ,J_c
• For center speaker--"CNTR SP"
_c_zAuYo
sPKt
[] [] ............
| r,| I h,,' ',,,;:h,,' _ _,, H|l 15
•"..':'": ': ':'.' ..... ...: i i i.... _
• For surround speakers--"SURR SP"
_c_zAuYo
sPKt
[] [] ............
• .. i | "...' ,',.., '... ,',..' ,, .... li| i
-.= =...= " ". i" ..... =i ==...=i " i..... 15
Select one of the following settings for each speaker:
LRG (large) Select when the size of the cone
speaker unit built in your speaker is
greater than 12 cm (4 3/4inches).
SML (small) Select when the size of the cone
speaker unit built in your speaker is
smaller than 12 cm (4 3/4inches).
NO Select when you have not connected a
speaker (not seiectable for the front
speakers).
Notes:
• "LRG(large)"istheinitialsettingforthefrontspeakersand
"SML (small)" for the center and surround speakers,
• If you have selected "SML (small)" for the front speakers, you
cannot select "LRG (large)" for the center and surround
speakers.
• Speaker distance
• For front distance---"FRNT D"
_c_zAuYo
sPKt
[] [] .................
• • = = • • • • ,, ,J =", ,== J
-. ,.,.".., , ," :: , ..',.""," Ic
." J '.." J J J,,' ,, ,J, ",,,' J ',' _._
I,J
• For center distance--"CNTR D"
_c_zAuYo
sPKt
[] [] ,", : | "1" :'% :% ,, ,1 ,", ,', :
L. i",." i K iJ ;; .L";3'._"ii:_ 15
• For surround distance--"SURR D"
sPKt
[] [] ...............
I I I I I I I I ". II 'j i"_1 i', ,j,,
-:= _.._ , =:. i '=:. i... = ==.i. _:._ ', L._, ]Cj
23