Panasonic Omnivision VHS PV-M2046 Operating Instructions Manual page 21

+
VCR Plus+ proglamnling allows you to set most items of a timer recording by simply entennga special code lound in I V GUIDE
magazineas well as the TV listings in selected newspapers. In order for the CombinationVCR to read this special code, some set up bs
required.A Guide (VCR Plus+)channel number is assigned to each local broadcastand cable station. Because this numbersometimes
differs from the channelyour TV receivesthe stationon, it is necessaryto program the CombinationVCR with local channel information.
_o.6"t5° 6'
,NpU_
-@o0 •
mOTA+E ro SELEC
9 ++:
C_"LAy Ve_+ _U_TO
oe
Channel Set Up Preparations
NOTE: Complete the steps on this page if your
VCR hook-up resembles "B" on page 20.
Prepare a list like the example below.
This list will help you smoothly enter the information
needed in step 4 at right.
You will need the following to complete the list:
• A line up of normal and/or cable stations you
receive along with the channel numbers your TV
receives them on. A cable channel line-up chart
is supplied by your cable company.
• A list of Guide (VCR Plus+) channel numbers
assigned to the stations you receive. This list is
available in TV Guide and the TV listings found
in selected newspapers.
1 Make a chart with 3 columns like the example
below. In the left column, fill in the name or call
letters of the stations you receive.
2 In the middle column, fill in each station's
assigned Guide (VCR Plus+) number found in
TV Guide, newspapers, etc.
3 In the right column, fill in the channel number
that your TV receives the station on from your
channel line-up.
EXAMPLE ONLY
Assigned Charmer no.
Broadcast or Cable Guide your TV
Station Name (VCR Plus+) receives the
channel no. station on
HBO 33 15
Nickelodeon 38 20
CBS 04 04
FOX 11
VCR Plus+ Channel Set Up
(For connection B on page 20 only)
Push MENU
C_ to display the
MENU menu.
Rotate and push
_ the WHEEL
to select "CH".
MAIN MENU
CH CLOCK EXIT
SELECT : ROTATE WHEEL
SET : PUSH WHEEL
Rotate and push
the WHEEL to
select VCR Plus+
CH SET UP.
- SET UP CHANNEL -1
/
ANTENNA SYSTEM : CATV /
AUTO SET |
SELECT ROTATE WHEEL /
SET PUSH WHEEL /
END PUSH MENU KEY /
)
IMPORTANT NOTE:
For this step, use the list you prepared. You may leave lines
blank if, you don't receive that station, or the GUIDE CH
number and the CATV (or TV) CH numbers are the same.
Push the
_ {_] WHEELto
move the
shaded area on
the right side.
VCR Plus+ CH SET UP
GUIDE CH CATV CH
02 --
SELECT ROTATE WHEEL
SET PUSH WHEEL
END PUSH MENU KEY
Then, Rotate the Wheel
to change CATV CH number.
Next, Push the Wheel
to enter CATV CH number.
Now, Rotate the Wheel to continue.
Repeat this operation until the list is complete.
To Make Corrections
Rotate and push the Wheel to select the incorrect CATV or TV
CH number. Then, Push CLEAR to delete the numbers.
Now, use the Wheel to re-enter the channel.
(CC>
MENU
Push MENU twice to
exit the VCR Plus+
CH SET UP mode.
_, Make your entrieswithin5 minutesor the
(NOTES} Combination VCR will leave thismode. :
• Once localchannelshave been programmed, { hey will
stay in memory, evenin the case of a powerfailure.
21