Related Manuals for Soundstream LIL'WONDER LW1.1100D
Summary of Contents for Soundstream LIL'WONDER LW1.1100D
-
Page 1: Installation Guide
Owner’s Manual and Installation Guide LW1.1100D LW1.1700D LW1.2600D... - Page 2 Please retain this manual and you sales receipt for future reference. Soundstream amplifiers are the result of American innovation and the highest quality control standards. When properly installed, they will provide you with many years of listening pleasure.
- Page 3 FEATURES Mono-Block Class D Amplifier Total Harmonic Distortion:0.5% Frequency Response: 15-150Hz Signal to Noise Ratio: 105dB Damping Factor: >250 Input Sensitivity 100mV - 8V 50-150Hz,12dB Low Pass Fiter 45Hz, 0-18dB Bass Boost 180° Phase Switch Midnight Black Finish w/ Brushed Accents Remote Gain Control Master/Slave Operation Pre-amp Outputs...
-
Page 4: Specifications
SPECIFICATIONS >105dB Signal/Noise Ratio Frequency Response 15Hz-150Hz 0.50% 50Hz -150Hz,12dB Input Voltage Range 11-16 Volts DC High Impedance RCA/LINE 30K Ohms Level Input Impedance POWER RATINGS & FUSE 4 ohm MODEL 2 ohm FUSE 1 ohm LW1.1100D 600W 900W 1100W 35A X 3 LW1.1700D 700W... -
Page 5: Tools/Parts For Installation
TOOLS/PARTS FOR INSTALLATION NOTE: TOOLS ARE NOT SUPPLIED Small flat blade screwdriver phillips screwdriver (#2 or medium sized), Wire cutters, Wire strippers, - #6 round head screws, and 1 - #8 sheet metal screw (or nut, bolt flat washer, start washer) (see detail) 2 Ring connectors (large enough to accommodate your method of grounding) In-line fuse or Grommets (Sized to work with the power wire you plan to use in your installation) Tube of silicone seal. - Page 6 Electrical Wiring All LIL’WONDER Amplifiers are equipped with easy top access screw terminals . These terminals are nickel-plated in order to ensure excellent electrical contact and to resist corrosion. When making electrical connections to the amplifier, please observe the following : Use at least 4 gauge or heavier wire for power and ground connections.
-
Page 7: Panel Layout
PANEL LAYOUT LW1.1100D LEFT VIEW Subsonic Low Pass Bass Input Line Out Line Input Level Filter Filter Boost PHASE PROTECTION 10Hz 40Hz 50Hz 150Hz +18dB Bridged Input Sensitivity Mode REMOTE DATALINK CONTROL .1V-2V 2V-8V Master Slave RIGHT VIEW BATT+ REMOTE POWER CONNECTIONS SPEAKER FUSES... -
Page 8: Low Level Inputs
PANEL LAYOUT LW1.2600D LEFT VIEW Input Subsonic Low Pass Bass Line Input Line Out Filter Filter Boost PHASE Level PROTECTION 10Hz 40Hz 50Hz 150Hz +18dB Bridged Input Sensitivity Mode REMOTE DATALINK CONTROL .1V-2V 2V-8V Master Slave RIGHT VIEW SPEAKER POWER CONNECTIONS Class D Monoblock Amplifier Installation Wiring LW1.1100D/LW1.1700D/LW1.2600D Low Level Inputs... - Page 9 Class D Monoblock Amplifier Installation Wiring LW1.1100D/LW1.1700D BATT+ REMOTE POWER CONNECTIONS FUSES SPEAKER LW1.1700D has four fuses here BATT+ REMOTE POWER CONNECTIONS SPEAKER FUSES LW1.1700D has four fuses here...
- Page 10 Class D Monoblock Amplifier Installation Wiring LW1.2600D SPEAKER POWER CONNECTIONS SPEAKER POWER CONNECTIONS...
- Page 11 Bridging Two LW1.1100D/LW1.1700D/LW1.2600D Amplifiers Input Subsonic Low Pass Bass Line Input Line Out Filter Filter Boost PHASE Level PROTECTION 10Hz 40Hz 50Hz 150Hz +18dB Bridged Input Sensitivity Mode REMOTE DATALINK CONTROL .1V-2V 2V-8V Master Slave Power Subsonic Low Pass Bass Input Line Out Line Input...
- Page 12 Bridging Two LW1.1100D/LW1.1700D Amplifiers BATT+ REMOTE POWER CONNECTIONS SPEAKER FUSES LW1.1700D has four fuses here BATT+ REMOTE POWER CONNECTIONS SPEAKER FUSES...
- Page 13 Bridging Two LW1.2600D Amplifiers SPEAKER POWER CONNECTIONS SPEAKER POWER CONNECTIONS...
-
Page 14: Troubleshooting
TROUBLE SHOOTING NO SOUND Is the LED lit? Check Power and Remote turn-on wire for voltage. Make sure Ground wire is secure. STILL NO SOUND See your Authorize Sound Stream Dealer. SOUND IN ONE CHANNEL ONLY Reverse left and right speakers by unplugging the speaker connector. turning it over and plugging it back in. - Page 15 Caution: Please do not plug in or unplug RCA Plugs to the amplifier inputs while the amplifier is turned on. Doing so is potentially harmful to the amplifier by allowing RF(radio frequencies) into the amplifier, causing instability, during the brief period while the RCA shield is not connected, and the hot is connected.