Page 1
OWNER'S MANUAL MODEL NO. 536.797571 CRAFTSMRN Caution: Read and Follow 3.5 HORSEPOWER All Safety Rules 9 INCH and Instructions Before Operating EDGER/TRIMMER This Equipment Assembly Operation Customer Responsibilities Service and Adjustments • Repair Parts SEARS, ROEBUCK AND CO., Hoffman Estates, IL 60179 U.S.A. Part No.
SAFETY RULES CAUTION: ALWAYS DISCONNECT SPARK PLUG WIRE AND PLACE WIRE WHERE IT/_. C NOT CO.TACT SPARK P'UG T O PREVENT AOC.DENTAL STA.T,NG WHEN T,NG uP, TRANSPORT,NG. ADJUST,NG OR MAK,.G REPA,RS BEFORE USE • Never operate the edger/trimmer at high transport speeds on slipperysurfaces.
TWO YEAR LIMITED WARRANTY ON CRAFTSMAN EDGER/TRIMMER Fortwo years from the date of purchase, when this Craftsman Edger/trimmer is maintained, lubricated and tuned-up accordingto the instructionsin the owner's manual, Sears will repair, free of charge, any defect in material and workmanship.
Page 4
TABLE OF CONTENTS OPERATION ..........9-13 SAFETY RULES ........... SERVICE AND ADJUSTMENTS ... 16-17 PRODUCT SPECIFICATIONS ...... 3 STORAGE ........... CUSTOMER RESPONSIBILITIES ..3,14,15 TROUBLE SHOOTING ....... WARRANTY ..........REPAIR PARTS TABLE OF CONTENTS ........ CONTENTS OF HARDWARE PACK .... 5 (EDGER/TRIMMER) ......
ASSEMBLY TOOLS REQUIRED FOR ASSEMBLY 2 - 1/2 inchWrenches (Oradjustablewrenches) 2 - 9/16 inchWrench ( or adjustablewrenches) 2 - AdjustableWrenches 1 - Knife 1 - Regular Screwdriver Figure 1 shows the edger/trimmercompletelyas- sembled. Referenceto the right and lelt hand side of the edger/ trimmeris from the operator'spositionbehindthe unit.
ASSEMBLY TO ASSEMBLE "IHE EDGER/TRIMMER • Attachthe left rearwheel to the edger/trimmer (See Fig. 2B) with a 3/8-16 x 1.39 inch shoulder bolt, NOTE: Lower handle should be attached first as it is spacer (.70 inchlong) and 3/8-16 hex head jam nut difficultto attach lower handle with the wheels on.
Page 8
ASSEMBLY • Placetheupper handleon the lowerhandle (See Fig. 3), align upperhandleholesinthe lowerhandle, and secure in placewithfour (4) 5/16-1B x 1-1/4 inchhex head screwsand four(4) 5/16-18 hex head Iocknuts (foundin pads bag). Locknuts shouldbeto the inside of the two handles as shown in Fig. 3. NOTE: Clutchlever islocated on the lefthand sideofthe upper handlewhen properlyinstalled.
Page 9
OPERATION KNOW YOUR EDGER/TRIMMER READ THIS OWNER'S MANUAL AND SAFETY RULES BEFORE OPERATING YOUR EDGER/ TRIMMER. Compare the illustrations with your edger/trimmerto familiarize yoursolfwith the locationof various controlsand adjustments. Save this manual for future reference. :H LEVER CONTROLROD INDEX LEVER BLADE FUEL FILL THROTTLE...
Page 10
OPERATION The operationofthis edger/trimrner can resultin foreignobjectsbeingthrowninto the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operatingthe edger/tdmmer. We recommend standard safety glasses or Wide Vision Safety Mask for over your glasses. HOW TO USE YOUR EDGER/TRIMMER TO STOP EDGER/TRIMMER BE IN THE EXTREME RIGHT POSITION...
Page 11
OPERATION TO USE CURB-HOPPING FEATURE TATING BLADE. THE BLADE CAN The adjustablefront and right rear wheel feature permit I& CAUTION: KEEP AWAY FROM THE RO- | CAUSE INJURY. theedger/trimmer to be used on anunevensurfaco(such as a curb] as shown In Fig. 8. BEFORE STARTING ENGINE •...
Page 12
OPERATION AND CAUTION MUST BE USED WHEN CAUTION: GASOLINE IS FLAMMABLE HANDLING OR STORING IT. DO NOT FILL FUEL TANK WHILE EDGER/TRIMMER IS RUNNING, HOT, OR WHEN EDGER/TRIMMER IS IN AN ENCLOSED AREA. KEEP AWAY FROM OPEN FLAME, ELECTRICAL SPARK, AND DO NOT SMOKE WHILE FILLING THE FUEL TANK.
OPERATION TO START THE ENGINE iiiii CAUTION: NEVER RUN THE ENGINE IN- Before startingthe engine, be sure you have read and DOORS OR IN A POORLY VENTILATED understoodall the instructionson the precedingpages. AREA. ENGINE EXHAUST CONTAINS The edger/trimmer is equippedwith a recoilstarter.The CARBON MONOXIDE, AN ODORLESS operation ofthe engine iscontrolledbythethrottlecontrol GAS AND DEAOLY GAS.
CUSTOMER RESPONSIBILITIES MAINTENANCE CHECK LIST SERVICE RECORD FILLIN DATES ASYOU COMPLETE REGULARSERVICE BEFORE STORAGE BEGINNING EACH SEASON EVERY 25 HOURS OF USE EVERY 10 HOURS OF USE EVERY 5 HOURS OF USE FREQUENTLY BEFORE EACH USE AFTER FIRST 2 HOURS OF USE LubriCateall Pivot Points LubricateWheal Axles Check Engine Oil Level...
CUSTOMER RESPONSIBILITIES • Remove the oilfill cap (see Fig. 9). • Fill the engine crankcase, pouring slowly. Do not overfill. For approximate capacity see PRODUCT SPECIFICATIONS on page 3 of this manual, • Reinstallthe oil tillcap and tighten securely. NOTE: The quill assembly bearings are factory sealed TO REMOVE and will requireno lubrication.
SERVICE AND ADJUSTMENTS CAUTION: DO NOT ATTEMPT SHARPEN THIS BLADE, YOU COULD AND DISCONNECT THE SPARK PLUG CAUSE DAMAGE TOTHE BLADEWHICH WIRE BEFORE MAKING ANY REPAIRS CAUTION: ALWAYS STOP THE ENGINE I COULD RESULT IN BREAKAGE AND TO THE EDGER/TRIMMER. POSSIBLE USER OR BYSTANDER JURY.
SERVICE AND ADJUSTMENTS TO replace the blade, do the following: • Disconnect the spark plug wire. • Removethe 1/2-20 Iocknut (See Fig. 14) secudng TIGHTENING the blade to the drive shaft, • Remove the blade, • installthe new blade and reinstall nut.Tighten the nut securely, •...
Ifyou do notwantto removegasoline,a fuelstabilizer IMPORTANT: A YEARLY CHECKUP OR TUNE-UP (suchas Sears Craftsman fuel stabilizer No. 33500) BY A SEARS SERVICE CENTER IS A may be added to any gasoline left in the tank to GOOD WAY OF ENSURING THAT minimize gum deposits and acids.
Page 19
TROUBLE SHOOTING TROUBLE CAUSE CORRECTION Stale fuel Drain fuel tank. Fill with fresh fuel. Difficult starting Clean and re-gap spark plug. Defective spark plug Replace fuel filter. Engine runs erratic Clogged fuel filter Clean fuel line; check gas tank. Blockedfuel line or empty fuel tank Have carburetor adjusted.