Yamaha S70XS Reference Manual page 111

Voice
This convenient operation lets you copy Effect and Master EQ settings of a
certain Voice to the currently edited Multi. This would come in handy when a
certain Voice has effect settings that you want to use in your Multi.
NOTE:
When this display is shown, you can hear the original sound at copy source by
pressing the [EDIT] button to call up the Compare mode. Pressing the [EDIT]
button again will exit from the Compare mode.
1 Source Voice
Determines the Bank and the Voice number to be copied.
Settings:
Bank: PRE1 – 8, USR1 – 4, PDR, UDR, GM, GMDR, Voice number: 001 (A01) – 128 (H16)
2 Determines which Effect units are copied
Determines which Effect or Master EQ settings of the Source Voice will be copied to the current Multi. You can select Effect units to be
copied from Reverb, Chorus, Master Effect and Master EQ.
NOTE:
Even when each of the Reverb and Chorus is set to "on," executing the Job does not copy the Send Level from the Voice to the
Multi. If you want to apply the same depth of the Reverb and Chorus as in the Voice mode to the copied Voice, set the Reverb
Send and Chorus Send in the Multi Mixing display of the Multi Part Edit mode to the same value manually as in the Voice Edit
mode.
Perf (Performance)
This convenient operation lets you copy Effect and Master EQ settings of a
certain Performance to the currently edited Multi. This would come in handy
when a certain Performance has effect settings that you want to use in your
Multi.
NOTE:
When this display is shown, you can hear the original sound at copy source by
pressing the [EDIT] button to call up the Compare mode. Pressing the [EDIT] button again will exit from the Compare mode.
1 Source Performance
Determines the Bank and the Performance number to be copied.
Settings:
Bank: USR1 – 4, Performance number: 001(A01) – 128(H16)
2 Determines which Effect units are copied
The Copy Job will copy all the parameters from the specified Performance to the specified Multi, basically. You can select Effect units to
be copied from Reverb, Chorus, Master EQ, Master Effect, A/D, Ins Sw.
3 Data type of the destination
Determines the Part of the destination Multi.
Settings:
part 1 – 4, part 5 – 8, part 9 – 12, part 13 – 16
NOTE:
The MIDI Receive Channel of the current Multi is specified as follows depending on the target parts.
part 1 – 4 Ch 1
part 5 – 8 Ch 5
4 Initialize
This function lets you reset (initialize) all Multi parameters to their default
settings. It also allows you to selectively initialize certain parameters, such as
Common settings, settings for each Part, and so on.
All (All Parameters)
All settings for the selected Multi are initialized. When this is set to on, the
cursor cannot be moved.
Common (Common Parameters)
Common parameter settings for the selected Multi are initialized.
NOTE:
The Insertion Effect Switch is a Part parameter. Therefore, checkmark the
desired boxes of Parts 1 – 16 (described below) if you wish to initialize the
Insertion Effect Switch parameter settings.
Part 1 – 16 (Part 1 – 16 Parameters)
Parameter settings for Parts which are turned on are initialized.
A/D (A/D Input Parameters)
This is the Part input from the external audio equipment connected to the MIC INPUT jack. Parameter settings for
the A/D input Part (page 98) of Common Edit are initialized.
part 9 – 12 Ch 9
part 13 – 16 Ch 13
Reference Manual
Reference
Basic Structure
Voice
Performance
Multi
SEQ Play
Master
Remote
File
Audio Rec/Play
Utility
Multi
Play
Mixing
Edit Select
Common Edit
Name
Arpeggio
Controller
Effect
Parameter
Master EQ
A/D Out
A/D FX
Parameter
Part Edit
Voice
Play Mode
Arpeggio
Arp Edit
Arp 1-5 Type
Filter/EG
3 Band EQ
Rcv Sw
FX Send
Job Select
Recall
Bulk
Copy
Initialize
Appendix
111