Table of Contents
Advertisement
INSTALLATION & OPERATION MANUAL
Thank you for purchasing this product from a fine line of heating equipment. Each unit is
constructed of the highest quality material and built by craftsmen who truly take pride in
their workmanship. Please read this manual before attempting to move or install your
unit.
We wish you many years of safe heating pleasure with your new heating
appliance.
CAUTION:
This unit must be installed in accordance with these instructions and must comply with
local building and fire codes. Failure to do so could result in a chimney or house fire.
Keep children, furniture, fixtures, and all combustible materials away from any heating
appliance. Maintain a minimum clearance of 30 inches (6 inches if using a heat shield)
from the firebox and 18 inches from the flue pipe to any combustibles, unless you are
using shielded or double wall pipe.
Visit our web site at
www.englandsstoveworks.com
for helpful information,
frequently asked questions, parts & accessory orders and more.
DO NOT INSTALL THIS UNIT IN A MOBILE HOME!!!
READ THESE INSTRUCTIONS CAREFULLY BEFORE INSTALLING THIS MODEL.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
NOTE: IF YOU HAVE A PROBLEM WITH THIS UNIT DO NOT RETURN IT TO
THE DEALER. CONTACT CUSTOMER SERVICE @ 1-800-245-6489.
MODEL 24-G FURNACE
England's Stove Works highly recommends the use of smoke detectors and
Carbon Monoxide detectors with any hearth product, including this unit. Follow all
manufacturer's instructions when using smoke or Carbon Monoxide detectors.
SAFETY NOTICE
IF THIS STOVE IS NOT PROPERLY INSTALLED, A HOUSE FIRE MAY
RESULT. FOR YOUR SAFETY, FOLLOW THE INSTALLATION DIRECTIONS.
CONTACT YOUR LOCAL BUILDING OR FIRE OFFICIALS CONCERNING
RESTRICTIONS AND INSTALLATION INSPECTIONS IN YOUR AREA.
Rev. 1/06
Advertisement
Table of Contents
Related Manuals for England's Stove Works 24-G
Summary of Contents for England's Stove Works 24-G
- Page 1 NOTE: IF YOU HAVE A PROBLEM WITH THIS UNIT DO NOT RETURN IT TO THE DEALER. CONTACT CUSTOMER SERVICE @ 1-800-245-6489. MODEL 24-G FURNACE England’s Stove Works highly recommends the use of smoke detectors and Carbon Monoxide detectors with any hearth product, including this unit. Follow all manufacturer’s instructions when using smoke or Carbon Monoxide detectors.
-
Page 2: Section I: Flue System
SECTION I: FLUE SYSTEM A. Existing Flue System If you have chosen a freestanding unit, this stove is designed to connect to an existing flue system, such as masonry or a pre-manufactured Class A flue system. If you have a masonry flue system, the inner liner should be inspected carefully for cracks; if there is no liner in your chimney, we recommend you install a steel liner or have one installed. - Page 3 We also recommend you have a flue clean-out door located at least two feet (2’) below your thimble for easy cleaning of the system. This door should be made as airtight as possible. It is the consumer’s responsibility to ensure the chimney system is safe and in good operating condition.
-
Page 4: Section Ii: Floor And Wall Protection
SECTION II: FLOOR AND WALL PROTECTION A. Floor Protection You will not need any floor protection if your floor is constructed of a non- combustible material such as brick or concrete. If your floor is constructed with a combustible material such as hardwood, carpet or linoleum, you must place protection between the stove and the combustible material. -
Page 5: Section Iv: Operating Instructions
NOTE: Install a 8” 90 degree elbow inside this hole so that air flow from central furnace will not be directed back into the hot air pipe from the add-on furnace. -
Page 6: Section V: Care And Maintenance
B. Draft Controls This unit has two draft controls on the door that control the amount of combustion air that enters the stove that in turn controls the amount of heat the unit generates. The controls are turned in a counterclockwise direction to let in more combustion air and produce more heat. -
Page 7: Section Vi: Chimney And Flue Pipe Maintenance
It is very important that installations are made airtight. This is best accomplished by using furnace cement at all pipe joints and where the first section enters the stove and the chimney thimble. Any existing air leaks will cause the air to draw at points where the least resistance is offered -- such places are pipe joints, flue thimble, flue openings in the chimney, ash clean-out doors and cracks in the chimney. -
Page 8: Section Viii: What Causes Creosote
This type cap will not correct a poorly constructed chimney or one in bad need of repair, however -- in some cases the system will require relining or even need to be rebuilt. REPLACEMENT PARTS LIST FOR 24-G AC-12 BLOWER THERMOSTAT... - Page 9 Have this information on hand if you phone the factory or your dealer regarding this product. Retain for your files: Model Number __________________________ Date of Purchase ________________________ Date of Manufacture _________________ Serial #_____________________ LIMITED 5 YEAR WARRANTY FROM THE DATE OF PURCHASE TO THE ORIGINAL OWNER The manufacturer extends the following warranties: Five Year Period:...
-
Page 11: Dealer Information
WARRANTY REGISTRATION for England’s Stove Works Purchased by (Name) ______________________________________________ Address _________________________________________________________ City ________________________ State __________ Zip _________________ Telephone _______________________________________________________ Email Address ___________________________________________________ Purchased From (Dealer) ___________________________________________ Address _________________________________________________________ City ________________________ State __________ Zip _________________ (Please be sure to refer to sticker on back of manual or box to complete this section) Model Number _____________________ Purchase Date _________________ Purchase Price ____________________ Serial Number _____________________ Mfg.