Related Manuals for Smart Technologies Rear Projection SMART Board 2000i
Summary of Contents for Smart Technologies Rear Projection SMART Board 2000i
- Page 1 2000i Interactive Whiteboard Projector Replacement Guide for Projector Replacement Kits NEC MT1060R (03-00043) and NEC MT860R (03-00041) 99-00496-00 Rev A0...
- Page 2 Copyright Notice © 2003 SMART Technologies Inc. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language in any form by any means without the prior written consent of SMART. Information in this manual is subject to change without notice and does not represent a commitment on the part of SMART.
-
Page 3: Table Of Contents
Contents Replacing the Projector in a 2000i........... 1 Aligning the Projected Image............6 Customer Support................11 Contacting SMART Technical Support ............11 Other SMART Contacts ................11 Product Warranty ..................11 99-00496-00 Rev A0... -
Page 5: Replacing The Projector In A 2000I
Replacing the Projector in a 2000i Use these instructions to install a replacement NEC MT860 or NEC MT1060 projector in your Rear Projection SMART Board 2000i interactive whiteboard. To remove the original projector 1. Shut down the computer, and then press and hold the Projector Standby button on the Control Panel until it blinks rapidly. - Page 6 5. With another person supporting the projector, reach through the view port and remove the three nuts (including the steel and nylon washers) that secure the projector in place and then remove the projector. Use the provided 7/16" nut driver to loosen the nuts. Keep the nuts and washers nearby, as you’ll need them when you install the new projector in step 8.
- Page 7 6. Set the projector down on a flat surface and remove the projector plate from the projector: Using the provided hex key, loosen and remove the four sets of screws, spacers and washers at the corners of the plate. Cap Screw Lock Washer Flat Washer Aluminum Spacer...
- Page 8 8. Slide the projector plate back into place by maneuvering the screws through the cabinet slots. With a partner supporting the bottom of the projector, use the provided 7/16" nut driver to secure the projector plate in place using the nuts and washers that you removed in step 5.
- Page 9 9. Connect the video, power and serial cables to the projector, along with any other cables (VCR, external monitor, etc.) that you removed in step 2. Power Cable Video Cable Serial Cable 10. Replace the strap that secures the projector to the projector plate. 11.
-
Page 10: Aligning The Projected Image
Aligning the Projected Image If the projected image is blurry or does not fit the screen, complete the four adjustment procedures that follow. For the first three, (roll, side-to-side and image size adjustment), you must watch the image on the back of the screen while making the adjustments. You must also remove the view port cover (attached with hook-and-loop fastener strips) at the rear of the unit to access the adjustment hardware. - Page 11 To adjust the image laterally 1. Crouch behind the projector and look at the projected image through the view port. Image Side-to-Side Adjustment 2. Using the supplied 7/16" nut driver, loosen the two nuts on the left side of the projector plate. 3.
- Page 12 To change the image size 1. Crouch behind the projector and look at the projected image through the view port. Image Size Adjustment 2. Loosen the four hex screws that secure the projector to the projector plate using the provided 3 mm hex key.
- Page 13 Screen Removed for Clarity As you maneuver the hex key through the access holes, watch it from the side to see when it engages with the hex screw. Look here to see when the hex key engages with the screw 4.
- Page 14 To move the image up or down 1. Crouch down in front of the screen. Move Image Up or Down 2. Look underneath the pen tray and locate the Electronics Tray. Locate a plastic cap on the right side of the Electronics Tray. Electronics Tray 3.
-
Page 15: Customer Support
Fax: +1.403.228.2500 E-mail: info@smarttech.com Our address: SMART Technologies Inc. Suite 600, 1177 11th Avenue SW Calgary, AB CANADA T2R 1K9 Product Warranty The replacement projector is covered by a two-year parts and labor warranty. Customers must return any defective merchandise to an authorized service center as directed by the distributor, dealer or manufacturer.