Advertisement
Quick Links
T
READAND UNDERSTAND THESEINSTRUCTIONS BEFOREINSTALLINGFIXTURE
lNSTRUCTION SHEET NO,
hisfktureisintended f or installation in ectordanse with the National Eladricd Code end Id
rsgulatbna,
o sssurs full sompfianca with Ixal OxJes snd rsgule.tkma,c+@ with your Ixd e!ectriral ins@or
Lwfora
wtallation. To prevent eleotrfd sheck, turn off elacbiciy at fuss box before premsding.
IS:40719
Retsinthese instructions for maintenance referenoe.
Pegelofl
INSTRUCTIONS
FOR
INSTALLATION
AND ASSEMBLY OF
RADIANCE STEM EXTENSION KITS
CAUTION:
BE CAREFUL WHILE HANDLING FIXTURE WIRES. DO NOT DAMAGE WIRE INSULATION
OR PINCH WIRES BETWEEN PARTS.
1.
Unps& CENTER STEM ASSEMBLY
(supplisd with f~re)
snd cmefuliy until
FIXTURE WIRES.
2. Gent~ pull downward en CANOPY to disengege fmm CROSSBAR SPRING CLIPS and expmw CROSSBAR (fig, 1),
3. Remove the two SCREWS from beth sides d SWIVEL CASTING snd skfe SWIVEL PIN oul fmm one d the holse in the SWIVEL CASTING (Fig, 1).
NOTE A small smswddver may be required to push SWIVEL
PINoutthrough tie hob in SWIVEL CASTING,
CAUTION:
PLACE SCREWS
AND
SWIVEL
PIN IN
A
SAFE
PLACE;
THESE
PARTS
ARE
NEEDED
FOR
FINAL
ASSEMBLY
OF EXTENSION
KIT.
4. While holding CENTER STEM ASSEMBLYsnd FIX7UREWIRES, genttfslikieSWlVELCASTlNGfCRQ3SsARAs3EMBLYup
FIXTURE WIRES UnfiIA~EMBLY
ISmmpletely rsmoved fmm FIXTURE WIRES (Fig. 2), Plain SWIVEL CASTING/CROSSBAR
ASSEMBLY ins safe place.
NOTE Make owtsin QUICK CONNECTORS at the lower
endofCENTER STEM AS3EMSLY donotslideupinsideSTEM,
=,
FIXTURE
WIRES
CROSSBAR
FIXTURE
WIRES
(UN.COILED)
CROSSBAR
SWIVEL
CASTING
SPRING
CLIPS
7
ZSP'N
SWIVEL
CASTING[
CENTER
STEM A SSEMBLY
SCREWS
CROSSBAR
ASSEMBLY
[SUPPLIED
WITH F IXNREI
I
CENTER
STEM
CANOPY
ASSEMBLY
FIG,1
FI
5. Pass FIXTURE WIRES through EXTENSION STEM COLIAR and EXTENSION STEM and slide EXTENSION STEM dewn FIXTURE WIRES until
EXTENSION STEM COL~R
meets CENTER STEM AssEMSLY (Fig. 3A),
6. Aligning the holes in the side of CENTER STEM ASSEMBLY WW tie UWSSCIW h~l~ in EXTENSION STEM COLIAR, SIIW COMR
to side in~~e
CENTER STEM ASSEMBLY and secure in place by installing the two screws providwJ whh EX7ENSION STEM KIT (fig, 3S),
NOTE Before preceedin~ repeat steps 5 snd 6 f a ssmnd EXTENSION STEM KIT is to b used,
7. Re.sssemble SWIVEL CASTING/CROSSBAR
ASSEMSLY te the end of WENSION
STEM by reveming steps 3 snd 4 above (Fig. 4),
8. Continue FIXTURE insfsllation by following instructions supplisd with FIXTURE,
NOTE FIXTURES are supplied with enough FIXTURE WIRE 10allow two EXTENSION STEM KITS to be insfsllsd. If only one EXTENSION KIT is uset
excass FIXTURE WIRES should be cut off making certain Mere is a minimum of 6' of FIXTURE WIRE sbeve CROSSBAR ASSEMSLY for OUTLET BOX WIRING,
':':
4=-:s::
1.1<>
l-l-i-c>
1.1 E la" % R%,gwywu'
Advertisement
