Onkyo TX-NR727 Owner's Manual page 86

■
Bluetooth connection cannot be built
When building a Bluetooth connection between the AV
receiver and your Bluetooth-enabled device for the first
time, if the connection is fail, you need to power off your
Bluetooth-enabled device and power on again to clear the
device name, and build the connection again.
If there is metallic object near the AV receiver, Bluetooth
connection may not be possible as the metal can effect on
the radio wave.
If the wireless LAN and Bluetooth connections are used at
the same time, try to connect the ETHERNET port and
router with the Ethernet cable after selecting "Wired" in
"Network Connection" setting in "Network" for a better
connection. (➔ pages 16, 72)
Music Server and Internet Radio
■
Can't access the server or Internet radio
Certain network service or contents available through this
device may not be accessible in case the service provider
terminates its service.
Check the network connection between the AV receiver
and your router or switch. (➔ page 16)
Make sure that your modem and router are properly
connected, and make sure they are both turned on.
Make sure the server is up and running and compatible
with the AV receiver. (➔ page 94)
Check the "Network"settings. (➔ page
■
Playback stops while listening to music files on
the server
Make sure your server is compatible with the AV receiver.
(➔ page 94)
If you download or copy large files on your computer,
playback may be interrupted. Try closing any unused
programs, use a more powerful computer, or use a
dedicated server.
If the server is serving large music files to several
networked devices simultaneously, the network may
become overloaded and playback may be interrupted.
Reduce the number of playback devices on the network,
upgrade your network, or use a switch instead of a hub.
■
Can't connect to the AV receiver from a Web
browser
If you're using DHCP, your router may not always allocate
the same IP address to the AV receiver, so if you find that
you can't connect to a server or Internet radio station,
recheck the AV receiver's IP address on the "Network"
screen. (➔ page
Check the "Network" settings.
USB Device Playback
■
Can't access the music files on a USB device
Make sure the USB device is plugged in properly.
The AV receiver supports USB devices that support the
USB mass storage device class. However, playback may
not be possible with some USB devices even if they
conform to the USB mass storage device class.
(➔ page 94)
Depending on the type of format, the playback from a USB
device may not be performed normally. Check the type of
the file formats that is supported.
USB memory devices with security functions cannot be
played.
Others
■
Standby power consumption
72)
In the following cases, the power consumption in standby
mode may reach up to a maximum of 8.6 W:
– The "HDMI CEC (RIHD)" setting is set to "On".
(Depending on the TV status, the AV receiver will enter
standby mode as usual.)
– The "HDMI Through" setting is set to other than "Off".
– The "Network Standby" setting is set to "On".
➔ pages
(
69, 70, 73)
If an MHL-enabled mobile device connected to the AUX
(front) input is charged, the power consumption in standby
mode will increase than the figure above.
72)
(➔ page 72)
(➔ page 95)
(➔ page 16)
En-86
■
The sound changes when I connect my
headphones
When a pair of headphones is connected, the listening
mode is set to Stereo, unless it's already set to Stereo,
Mono, Direct, or Pure Audio (European, Australian and
Asian models).
■
The speaker distance cannot be set as required
The values entered may be automatically adjusted with
values best-suited for your home theater.
■
The display doesn't work
The display is turned off when the Pure Audio (European,
Australian and Asian models) listening mode is selected.
■
How do I change the language of a multiplex
source
Use the "Multiplex" setting in the "Audio Adjust" menu to
select "Main" or "Sub". (➔ page 62)
■
The functions don't work
To use , you must make an connection and an
analog audio connection (RCA) between the component
and AV receiver, even if they are connected digitally.
(➔ page 20)
While Zone 2/3 is selected, the functions don't work.
(➔ page 20)
■
The functions System On/Auto Power On and
Direct Change don't work for components
connected via
These functions don't work when Zone 2/3 is turned on.
(➔ page 20)
■
When performing "Automatic Speaker Setup",
the measurement fails and the message
"Ambient noise is too high." is displayed.
This can be caused by a malfunction in your speaker unit.
Check if the unit produces normal sounds.
■
The following settings can be made for the
composite video inputs
You must use the buttons on the unit to make these
settings.
Appendix