Onkyo TX-NR727 Owner's Manual page 72

Default setting: On (European, Australian and
Asian models), Off (North American and
Taiwanese models)
Note
• Set to " On" , the Auto Standby function may activate itself
during playback with some sources.
• The Auto Standby function does not work when Zone 2/3 is
on.
■
HDMI Through
Off
On
This setting enables or disables the Auto Standby
during HDMI Through by detecting the audio/video
input signal.
When this setting is set to "On", the AV receiver will
automatically enter standby mode if there is no audio
and no video signal input during HDMI Through for 30
minutes. (
The Auto Standby function does not work when
)
Zone 2/3 is on.
When this setting is set to "Off", the status of HDMI
Through is continued regardless of audio/video input
signal.
Tip
• Entering standby mode is possible by setting "HDMI CEC
(RIHD)" to "On" and using CEC-compatible component
regardless of the above-mentioned setting.
See "HDMI CEC (RIHD)" in "7. Hardware Setup" for linked
operation (➔ page 69).
• When the HDMI Through is enabled, the power
consumption slightly increases.
Note
• This setting is fixed to "Off" when "Auto Standby" is set to
"Off".
Network
This section explains how to configure the AV
receiver's network settings manually.
After modifying the network settings, you must
confirm the changes by executing "Save".
If your router's DHCP server is enabled, you don't
need to change any of these settings, as the AV
receiver is set to use DHCP to configure itself
automatically by default (i.e., DHCP is set to
"Enable"). If, however, your router's DHCP server is
disabled (you're for example using static IP), you'll
need to configure these settings yourself, in which
case, a knowledge of Ethernet networking is
essential.
What's DHCP?
DHCP (Dynamic Host Configuration Protocol) is used
by routers, computers, the AV receiver, and other
devices to automatically configure themselves on a
network.
What's DNS?
The DNS (Domain Name System) translates domain
names into IP addresses. For example, when you
enter a domain name such as www.onkyousa.com in
your Web browser, before accessing the site, your
browser uses DNS to translate this into an IP
address, in this case 63.148.251.142.
■
Network Connection
Wired
Wireless
This setting determines whether you connect the AV
receiver to network by wired LAN or wireless LAN. If
you connect by wireless LAN, select "Wireless". See
"Performing Wireless LAN Setup" for setting
(➔ page 27).
Tip
• The same setting is available even if "Wireless" is selected
in "Network Connection" in initial setup
En-72
■
MAC Address
This is the AV receiver's MAC (Media Access
Control) address. This address cannot be changed.
■
DHCP
Enable
Disable
This setting determines whether or not the AV
receiver uses DHCP to automatically configure its IP
Address, Subnet Mask, Gateway, and DNS Server
settings.
Note
• If you select "Disable", you must configure the "IP
Address", "Subnet Mask", "Gateway", and "DNS Server"
settings yourself.
■
IP Address
Class A:
"10.0.0.0" to "10.255.255.255"
Class B:
"172.16.0.0" to "172.31.255.255"
Class C:
"192.168.0.0" to "192.168.255.255"
Enter a static IP address provided by your Internet
Service Provider (ISP).
Most routers use Class C IP addresses.
■
Subnet Mask
Enter the subnet mask address provided by your ISP
(typically 255.255.255.0).
■
Gateway
Enter the gateway address provided by your ISP.
■
DNS Server
Enter the DNS server address provided by your ISP.
■
Proxy URL
To use a Web proxy, enter its URL here.
(➔ page 23).
Advanced Operations
Operating
procedure
(➔ page 56)