Download Print this page

Lincoln Electric CAN-M306 Datasheet

Covered electrode

Advertisement

Quick Links

M A T E R I A L S A F E T Y D A T A S H E E T
Conforms to Workplace Hazardous Materials Information System (WHMIS) Rev. November, 1988
The Lincoln Electric Company of Canada LP
179 Wicksteed Avenue
Toronto, Ontario M4G 2B9 CANADA
Phone: (416) 421-2600
I M P O R T A N T !
This section covers the materials from which this product is manufactured. The fumes and gases produced during welding with the normal use of this
product are covered by Section VII; see it for industrial hygiene information.
CAS Number shown is representative for the ingredients listed. All ingredients listed may not be present in all sizes.
(1)
The term "hazardous" in "Hazardous Ingredients" should be interpreted as a term required and defined in the Hazardous Products Act and does
not necessarily imply the existence of any hazard.
Ingredients:
Cellulose and other carbohydrates
Silicates and other binders
Iron
Titanium dioxides (as Ti)
Mineral silicates
Manganese and/or manganese alloys and compounds (as Mn)
Iron oxides (as Fe)
Magnesite
Alkali carbonates
Molybdenum alloys (as Mo)
Carbon steel core wire
Notes:
(*) Not listed. Nuisance value maximum is 10 milligrams per cubic
meter. TLV value for iron oxide is 5 milligrams per cubic meter.
(**)
As respirable dust.
Physical data such as odor, vapor pressure, density, evaporation rate and freezing or boiling points are not listed as they are not applicable to
this product and its use.
Non Flammable; Welding arc and sparks can ignite combustibles and flammable products. See CSA W117.2 Section 9.7 as referenced in
Section VIII. Product is inert, no special handling or spill procedures required.
Rev 3/07
For Welding Consumables and Related Products
Section I & II - Preparation and Product Information
Section III - Hazardous Ingredients (1)
Section IV - Physical Data
Section V - Hazard Data
Date:
5/25/07
Trade Name:
Shield Arc HYP+
Sizes:
All
Supersedes:
5/24/04
Product Type:
Representative Classifications:
Prepared by The Lincoln Electric Company, Cleveland, Ohio, USA
(216) 481-8100, on the date shown above.
TLV
CAS No. Wt. %
mg/m
65996-61-4
1-5
1344-09-8
1-5
7439-89-6
1-5
13463-67-7
1-5
1332-58-7
1-5
7439-96-5
1-5
65996-74-9
0.1-1
1309-48-4
0.1-1
584-08-7
0.1-1
7439-98-7
0.1-1
7439-89-6
60-100
(LDLo, LCLo) Lowest published toxic concentration.
MSDS No.:
CAN-M306
Covered Electrode
AWS E7010-P1
CSA E4910-P1
LD
50
3
(Route/Species)
10*
Not Available
1153 mg/kg
10*
(oral/rat)
10*
Not Available
10
Not Available
590 g/kg LDLo
5**
(oral/rat) reproductive
9 g/kg
0.2
(oral/rat)
5
Not Available
10
Not Available
1870 mg/kg
10*
(oral/rat)
114 mg/kg LDLo
10
(intraperitoneal/rat)
10*
Not Available
(CONTINUED ON SIDE TWO)
3
LC
mg/m
50
(Route/Species)
Not Available
Not Available
Not Available
Not Available
Not Available
2.3 LCLo
(inhalation/human)
Not Available
Not Available
Not Available
Not Available
Not Available

Advertisement

loading

Summary of Contents for Lincoln Electric CAN-M306

  • Page 1 The Lincoln Electric Company of Canada LP CSA E4910-P1 179 Wicksteed Avenue Toronto, Ontario M4G 2B9 CANADA Prepared by The Lincoln Electric Company, Cleveland, Ohio, USA Phone: (416) 421-2600 (216) 481-8100, on the date shown above. Section III - Hazardous Ingredients (1) I M P O R T A N T ! This section covers the materials from which this product is manufactured.
  • Page 2 Product: Shield Arc HYP+ Date: 5/25/07 Section VI - Health Hazard Data and Toxicological Properties Acute Lethality Values : LC 50 means the concentration of a substance in air that when administered by means of inhalation over a specified length of time in an animal assay, is expected to cause the death of 50% of a defined animal population. LD 50 means the single dose of a substance that, when administered by a defined route in an animal assay, is expected to cause the death of 50% of a defined animal population.

This manual is also suitable for:

Shield arc hyp+