Table of Contents
Advertisement
Receiver and Remote Control Programming
NOTICE: To comply with FCC/IC rules, adjustment or modifications of this
receiver and/or transmitter are prohibited, except for changing the code
setting or replacing the battery. THERE ARE NO OTHER USER
SERVICEABLE PARTS.
SECURITY
Your garage door opener receiver and remote control
transmitter have been set at the factory to a matching
code. The door will open when you press the LARGE
remote control push button.
Your SECURITY opener will operate with:
• several SECURITY remote controls utilizing up to 8
functions. NOTE: Open/Close/Stop operation counts
as 1 function.
• one Keyless Entry System (with SECURITY logo)
Follow the instructions below to program your opener to
match any additional remotes you may purchase. See
Accessories on page 34.
To Add A Remote Control
1. Press and hold the selected remote control push
button. See Figure 1.
2. Press and release the "Smart" (learn) button on the
right side of the opener (see Figure 2). The indicator
light on the panel will begin to blink and the opener
lights will flash once.
3. Release the remote push button.
Now the opener will operate when that remote control
button is pressed. Test it by pressing the remote button
to see that the door goes up and down.
Adding a remote can also be done from the door
control, as follows:
1. With the door closed, press and hold a remote push
button.
2. Press and hold the Light button on the door control.
3. Press and hold the door control push bar.
4. After the opener lights flash, release all buttons.
Test by pressing the remote push button.
To Erase All Remote Control Codes
Press and hold the "Smart" button on the opener panel
until the indicator light turns off (about 6 seconds). All
transmitter codes are now erased. Then follow the steps
above to re-program each remote control.
To Control the Opener Lights
With SECURITY transmitters, a remote push button
can be programmed to operate the opener lights without
opening the door.
1. With the door closed, press and hold the remote
button that you want to control the light.
2. Press and hold the Light button on the door control.
3. Press and hold the Lock button on the door control.
4. After the opener lights flash, release all buttons.
Test by pressing the remote push button. The opener
lights should turn on or off but the door should not move.
Children operating or playing with a garage
door opener can injure themselves or others.
The garage door could close and cause
serious injury or death. Do not allow children
to operate the Door Control or remote control
transmitter(s).
A moving garage door could injure or kill
someone under it. Activate the opener only
when you can see the door clearly, it is free of
obstructions, and is properly adjusted.
SECURITY 3-Channel Remote Control
Figure 1
Figure 2
1
2
9
7
5
KG
Open/Close/Stop Operation
Your SECURITY remote control can be programmed
to operate one door using all 3 buttons: the large button
will only open the door, the middle button will only close
the door, and the third button will stop the door's
movement. You may set up this feature as follows:
1. With the door closed, press and hold the
large remote push button.
2. Press and hold the Lock button
on the door control.
3. Press and hold the door control
push bar.
When the opener lights flash, release all buttons. Test
by pressing the large (Open) button on the remote. The
door should open. Press it again while the door is open
and nothing should happen. Press the middle (Close)
button and the door should close. Press the third (Stop)
button while the door is moving and it should stop
immediately.
Model 976LMC SECURITY Keyless Entry
Follow instructions on page 34 (Accessories).
29
WARNING
Model 973LM
Select a
push button
SECURITY
Garage Door Opener
1
2
9
9
1
7
7
3
5
KG
"Smart" (learn)
Indicator Light
Button
RIGHT PANEL
3
1
9
1
3
7
3
5
KG
Code programming instructions
are also located
on the opener panel.
Stop
3
1
3
5
KG
Open
Close
Advertisement
Table of Contents
