Table of Contents
Advertisement
Troubleshooting
If you experience problems, refer to the relevant item
and take the appropriate measures.
Power does not turn on
• Is the AC/AC power supply connected to an
outlet? ( p.12)
• Is the [POWER] switch turned on?
Turn on the front panel [POWER] switch. ( p.15)
Power is on, but nothing is displayed in the LCD
screen
• Perform the following procedure. ( PG p.110)
1 Press the [EXIT] key three times, and press the
[GLOBAL] key.
2 Hold down the [EXIT] key, and press the
[WRITE] key.
3 Rotate the [VALUE] dial to adjust the LCD
screen.
No sound
• Are connections made correctly to your amp,
mixer, or headphones? ( p.12)
• Is your amp or mixer turned on?
• The [OUTPUT] knob may have been turned all the
way to the left. ( p.4)
• If a specific track/timbre does not sound in
Combination or Multi modes, make sure that its
"Status" is set to INT or BTH. ( PG p.36, 54)
• Are the Key Zone and Velocity Zone set so that
sound will be produced? PG p.39, 40, 56, 57)
• If there is no sound from the AUDIO OUTPUT
(INDIVIDUAL) 1–4 jacks, make sure that "BUS
Select" or "Bus Select" following the insert effect is
set to 1, 2, 3, 4, 1/2, or 3/4. ( p.95–)
Notes do not stop
• In PROG 2.1: Ed–Basic, select the Prog Basic page,
make sure that the "Hold" check box is unchecked.
( PG p.5)
Cannot input sound
• Is your audio source connected to the AUDIO
INPUT 1, 2 jacks? ( p.68)
• Is the [INPUT] knob raised? ( p.68)
• Is the [MIC/LINE] switch set appropriately?
( p.68)
• If there is no sound in Sampling mode, go to SMPL
1.1: Recording, select the Input/Pref page, and
make sure that "Lvl" and "BUS" are set correctly.
( p.69)
• If there is no sound in Program, Combination, or
Multi modes, go to GLOBAL 1.1: System, select the
Appendices
• If sound is still not input even after you have set
Noise or oscillation is heard
• When using an effect on the external audio source
• After a sample edit has been executed, or after a
• When using the BPM/MIDI Sync function to
Effects are not applied
• Are the GLOBAL 1.1: System, Basic page "IFX1–5
• If you are in Combination, or Multi modes, and
Cannot record a sample
• Are one or more SIMM modules installed? ( PG
• Is there free memory area ( PG p.103)
Audio In page, and make sure that "Input1 Level,"
"Input1 BUS Select," "Input2 Level" and "Input2
BUS Select" are set correctly. ( p.97)
"Input 1 Level," "Input 2 BUS Select," "Input 2
Level," and "Input 2 BUS Select" in the GLOBAL
1.1: System, Audio In page, temporarily lower the
"Input 1 Level" and "Input 2 Level," and then
move to Program, Combination, or Multi mode.
Turn return to Global mode, and make the settings
once again.
being input from AUDIO INPUT 1 and 2,
oscillation may occur depending on the type of
effect or on the parameter settings. Please adjust
the input level, output level, and effect parameters.
You need to be particularly careful when using a
high-gain effect.
stereo sample has been recorded, a small noise
may be heard. This has no effect on the audio data
that was edited or sampled.
control the delay time of an effect, noise may occur
in the delay sound. This noise is due to
discontinuities in the delay sound, and is not a
malfunction.
Off," "MFX1 Off," or "MFX2 Off" settings
checked? ( p.99)
master effects are not applied when you raise the
"S1 (Send1(MFX1))" or "S2 (Send2(MFX2))" of the
timbre/track, does "Rtn (Return1)" or "Rtn
(Return2)" from the master effect need to be
raised? ( PG p.148)
Alternatively, has "Send1" or "Send2" for each
oscillator of the program used by the timbre/track
been lowered? ( PG p.26, 28)
The actual send level is determined by multiplying
the send setting of each oscillator in the program
with the send setting of the timbre/track.
p.243)
Select a different memory bank. ( PG p.77)
Delete unneeded samples. ( PG p.80)
Save important samples before deleting them. ( PG
p.80, 134)
103
Advertisement
Table of Contents
