Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Carrier 42VMC Console night & day
Summary of Contents for Carrier 42VMC Console night & day
- Page 1 42VMC Console ISO 9001 INSTALLATION MANUAL...
-
Page 2: Table Of Contents
42VMC Split system “Console night & day” indoor unit The operation and maintenance instructions for the indoor unit and the installation instructions for the indoor and the outdoor unit are given in the manuals for each unit. These are supplied with the unit. -
Page 3: Dimensions And Weight
42VMC Dimensions and weights - Minimum clearances (mm) Dimensions and weights Minimum clearances Wall installation 50 min Ceiling installation Ø 80 50 min Model 42VMC009 42VMC012 42VMC014 42VMC018 42VMC024 1000 1000 1000 Table I: Nominal data POWER INPUT Cooling only •... -
Page 4: Connections
42VMC Connections E N G L I S H Note: Outdoor unit Height difference / Connection length / Pipe bends: Indoor unit See outdoor unit installation manual. Height difference Table II: Material supplied Photocatalytic filter Acrylic-fibre filter Condensate drain pipe cover (use for horizontal installation) •... -
Page 5: General Information
• This installation manual describes the installation procedures of the indoor unit of a residential split system consisting of two units manufactured by Carrier. • Choose an area free from obstructions which may cause irregular Consult factory or a qualified system engineer prior to connecting air distribution and/or return. -
Page 6: Warnings: Avoid
42VMC Warnings: avoid… E N G L I S H ...exposure to direct sunshine, when unit is operating in cooling ...any obstruction of the unit air outlet or return. mode; always use shutters or shades..positions too close to heating sources which may damage the unit..connecting condensate piping to sewage system drain without ...exposure to oil vapours. -
Page 7: Installation
42VMC Installation Vertical wall-mounting Hole Plate Template • The preferred arrangement is generally under a window sill on an Ceiling installation external wall. This makes it easier to install the interconnecting tubing, • Using the template supplied, drill the four holes in the ceiling and electrical connections and condensate pipework to the outdoor position four tie rods (not supplied). - Page 8 42VMC Installation E N G L I S H Drilling the hole in the wall for the For horizontal installation connection of the pipes To allow the condensate drain pipe to correctly come out of the unit, proceed as follows: Ø...
-
Page 9: Refrigerant Connections
42VMC Refrigerant connections Make refrigerant connections before connecting the system to Connection to the unit the power supply. Insufficient tightening torque will cause gas leaks. Refer to the outdoor unit installation manual for tube sizing, Overtightening the fittings will damage the tube flaring and cause and limitations (slopes, length, number of curves allowed, gas leaks. -
Page 10: Electrical Connection
42VMC Electrical connections E N G L I S H The mains supply must be connected as follows: Models 42VMC 009, 012, 014: to the indoor unit. Models 42VMC 018, 024: to the outdoor unit. • Make electrical connections between units prior to proceeding to mains supply unit connection. -
Page 11: Cooling Only
42VMC Electrical connections Cooling only 42VMC 009, 012, 014 Unit System 42VMC 018, 024 Unit System Minimum connection wire size between indoor and outdoor units (mm Model 42VMC 009 – – 42VMC 012, 014 – – 42VMC 018, 024 – –... -
Page 12: Heat Pump
42VMC Electrical connections E N G L I S H Heat pump 42VMC 009, 012, 014 Unit System 42VMC 018, 024 Unit System Minimum connection wire size between indoor and outdoor units (mm Model 42VMC 009 – – – 42VMC 012, 014 –... -
Page 13: System Configuration
42VMC System configuration System configuration Cooling only configuration (of the remote controller) • Insert the batteries into the remote controller and leave it OFF. Units are factory configured as heat pumps. • Energize the system, turning the power supply ON. When a cooling only system is installed, it is necessary to change •... -
Page 14: Operating Test
42VMC Operating test, address selector, fault code, guide for the owner and accessories E N G L I S H Operating test Fault code • Perform the operating test after the units have been installed in Once a failure occurs with the indoor unit in operation, the green position and the gas leak test has been completed. -
Page 15: Air Delivery
42VMC Air delivery and fresh air renewal Air delivery direction Wall installation, cooling Wall installation, heating Ceiling installation, cooling Ceiling installation, heating “No draught” (guide vane fully open) (position recommended for ceiling installation in cooling mode, to avoid draughts) Make absolutely sure that the above parts are not obstructed IMPORTANT: (even partially). - Page 16 L010125H33 - 0402 Via R. Sanzio, 9 - 20058 Villasanta (MI) Italy - Tel. 039/3636.1 The manufacturer reserves the right to change any product specifications without notice. Order No. 14489-74, April 2002. Supersedes Order No. 14489-74, January 2002. Printed in Italy...