Tv Operation; Starting Setup; To Select Video Input Source; To Select Analog/Digital Channels - Sansui SLED2480 Owner's Manual

Starting setup

The Auto Setup menu appears the first time you
turn on the TV, and assists you to specify the
Air/Cable setting, and program your channels
automatically.
IMPORTANT: Make sure that the antenna or cable
TV system connection is made!
1
To turn on the TV, touch
indicator on the front of the unit changes blue.
It may take approx. 10 seconds for a picture to
appear on screen.). The starting setup function
begins.
Auto Setup
Signal Type Cable
Automatic Search Start
: Adjust
: Select
2
Press ◀ or ▶ to select "Cable" or "Air".
3
Press ▲ or ▼ to select "Automatic Search", then
press ▶ or ENTER.
4
"Auto Setup" will begin. After the starting setup
is completed, the TV channel appears on the
screen.
•
Depending on the reception condition, it may take up
to 30 minutes to complete memorizing digital cable
channels. Please allow the process to complete
without interruption.
NOTE:
• If you press ENTER in the process of "Auto Setup",
the Starting Setup stops and changes to the normal
screen.
• When you make a menu selection, your changes
occur immediately. You do not have to press EXIT to
see your changes.

TV operation

1
To turn on the TV, touch
(POWER indicator on the front of the unit
changes blue. It may take approx. 10 seconds for
a picture to appear on screen.)
2
Adjust the volume level by pressing VOL + or – .
The volume level will be indicated on the screen
by blue bars. As the volume level increases, so do
the number of bars. If the volume decreases, the
number of blue bars also decreases.
3
Set the Signal Type option to the appropriate
position (see "Air/Cable selection" on page 18).
4
Press the Direct Channel Selection (0-9, –)
buttons to select the channel.
(If you press only channel number, channel
selection will be delayed for a few seconds.)
(POWER) (POWER
(POWER).
TO SELECT ANALOG CHANNELS
1-9: Press 1-9 as needed. Example, to
select channel 2, press 2, then press
ENTER.
10-99: Press the 2 digits in order. Example,
to select channel 12, press 1, 2, then
press ENTER.
100-135: Press the 3 digits in order. Example, to
select channel 120, press 1, 2, 0, then
press ENTER.
TO SELECT DIGITAL CHANNELS
Press the first 1-3 digits, then press the – button,
followed by the remaining number.
Example, to select channel 15-1, press 1, 5, –, 1,
then press ENTER.
• If a channel is selected with only audio content,
"Audio only" will be displayed on the screen.
• If a channel is selected with a weak digital
signal, "Digital channel signal strength is low"
will be displayed on the screen.
The same program may be available on either
an analog channel or a digital channel. You may
choose to watch either format.
• If a channel is selected to which you have not
subscribed, "Digital channel is encrypted" will
be displayed on the screen.
VHF/UHF/CABLE CHANNELS
Air
VHF
2-13
UHF
14-69 14-36
37-59
60-85
86-94
95-99
100-135
01
NOTE:
• If a channel with no broadcast is selected, the
sound will automatically be muted.
• It may take a few seconds for a digital channel
picture to appear on screen after being selected.
To select the video input source
To view a signal from another device connected to
your LCD TV, such as a VCR player, press INPUT
SELECT, then press ▲/▼ or corresponding Number
buttons (0-5), then press ENTER. You can select TV,
Video, Component, HDMI1, HDMI2 or PC depending
on which input jacks you used to connect your
devices.
Input Select
0.TV
1.Video
2.Component
3.HDMI1
4.HDMI2
5.PC
[0-5]:Select
CH /
Press and release CH
automatically stops at the next channel set into
memory.
For proper operation, before selecting channels, they
should be set into the memory. See "Memorizing
channels" on pages 18 and 19.
Cable
VHF
2-13
STD/HRC/IRC
(A) (W)
(AA) (WW)
(AAA) (ZZZ)
(86) (94)
(A-5) (A-1)
(100) (135)
(4A)
/ . The channel
15