Table of Contents
Advertisement
Quick Links
INSTALLATION INSTRUCTIONS
HB0056
64000 SERIES
INTENDED FOR DOMESTIC COOKING ONLY
!
!
READ AND SAVE THESE INSTRUCTIONS
INSTALLER: LEAVE THIS MANUAL TO HOMEOWNER.
HOMEOWNER: USE AND CARE INFORMATION ON PAGES 11 TO 13
Broan-NuTone LLC, 926 West State Street, Hartford, WI 53027 (1-800-637-1453)
NuTone Inc., 4820 Red Bank Road, Cincinnati, OH 45227 (1-800-543-8687)
Broan-NuTone Canada Inc., 1140 Tristar Drive, Mississauga, ON L5T 1H9 (1-888-882-7626)
REGISTER YOUR PRODUCT ON LINE AT: www.broan.com/register
V03515 rev. J
Advertisement
Table of Contents
Related Manuals for Broan Elite 64000 SERIES
Summary of Contents for Broan Elite 64000 SERIES
-
Page 1: Installation Instructions
Broan-NuTone LLC, 926 West State Street, Hartford, WI 53027 (1-800-637-1453) NuTone Inc., 4820 Red Bank Road, Cincinnati, OH 45227 (1-800-543-8687) Broan-NuTone Canada Inc., 1140 Tristar Drive, Mississauga, ON L5T 1H9 (1-888-882-7626) REGISTER YOUR PRODUCT ON LINE AT: www.broan.com/register V03515 rev. J... -
Page 2: To Reduce The Risk Of Fire, Electric Shock Or Injury To Persons, Observe The Following
To reduce the risk of fire and electric shock, the Broan Elite 64000 Series hood must be installed with Broan interior blower models P5 or P8; Broan exterior blower models 331H, 332H, 335 or 336; Broan in-line blowers models HLB3, HLB6, HLB9, HLB11. -
Page 3: Range Hood System
64000 SERIES RANGE HOOD SYSTEM - INTERIOR BLOWERS Model 647 Model 634 or 644 Model 643 (7” Rd wall cap) (roof cap) (8” Rd wall cap) Model 418 10” round Model 415 adjustable elbow 7” round adjustable (optional) elbow (optional) 8”... - Page 4 64000 SERIES RANGE HOOD SYSTEM - IN-LINE AND EXTERIOR BLOWERS Model 441 Model 437 (10” Rd wall cap) Model HLB9 (800 cfm) (High capacity roof cap) Model 335 (1200 cfm) or HLB11 (1100 cfm) or 336 (1500 cfm) in-line blower exterior blower Model 331H (600 cfm) (includes two 8”...
-
Page 5: Select Blower Option And Install Ductwork
1. SELECT BLOWER OPTION AND INSTALL DUCTWORK Either an interior or exterior blower or in-line blower may be used with this hood. The Broan Elite 64000 Series must be installed with blower models P5, P8, HLB3, HLB6, HLB9, HLB11, 331H, 332H, 335 or 336 only. Other blowers cannot be substituted. -
Page 6: Prepare The Installation
2. PREPARE THE INSTALLATION Make sure that the following items are included: - Range hood - Accessories: • Filters • Bag of parts including: (4) lock nuts, (1) wire clamp, (8) 1/2” double thread screws, (2) wire connectors, (2) 1/2” standard screws, (6) 3/8” screws. Parts sold separately: - Interior blower Model P5 includes blower, rough-in kit, flow deviator and 3 ”... - Page 7 5. CHOOSE THE OPENING (INTERIOR BLOWER) Remove the knockout for the chosen opening (horizontal at the back of the hood or vertical on rough-in plate). See pictures below. CAUTION When using P5 blower, remove the 10’’ wide knockout (smaller part). If using P8 blower, remove the knockout corresponding to the ducting installed (10’’...
- Page 8 8. INSTALL THE ADAPTER (INTERIOR BLOWER) Using two (2) standard 1/2’’ screws, secure the adapter to the top (or back) of the hood. Seal the adapter to the hood using duct tape. HD0005 HD0006 9. INSTALL THE HOOD (ALL BLOWERS) INTERIOR BLOWER: Run power cable to installation location.
-
Page 9: Connect Wiring (All Blowers)
10. CONNECT WIRING (ALL BLOWERS) WARNING Risk of electrical shock. Electrical wiring must be done by qualified personnel in accordance with all applicable codes and standards. Before connecting wires, switch power off at service panel and lock service disconnecting means to prevent power to be switched on accidentally. INTERIOR BLOWER: Connect cable into wiring box using wire connectors. - Page 10 11. INSTALL THE BLOWER (INTERIOR BLOWER) (CONT’D) Install screws into the location as shown in the pictures below (single blower or dual blower). Do not tighten screws down fully, leave a 1/8” gap. Hang blower unit onto blower plate (screws through the large part of the keyhole). Slide the blower to its position (screws in the small part of the keyhole).
-
Page 11: Light Bulbs
12. LIGHT BULBS This range hood uses 50W halogen lamps. (120V, 50W, PAR 20) Install the lamps by rotating them clockwise into their socket holder. 13. HEAT LAMPS The heat lamps required are 120V, 175W max, infrared bulbs. (120V, IR 175W, PAR 38) White halogen lights can be used if warming shelves are not used. -
Page 12: Operation
15. USE AND CARE (CONT’D) Hood cleaning Stainless steel cleaning: How to maintain its « BRIGHT LOOK » - Regularly wash surfaces with clean cloth or rag soaked with warm water and mild soap or liquid dish detergent. - Always clean in the direction of original polish lines. - Always rinse well with clear water (2 or 3 times) after cleaning. -
Page 13: Warranty
This warranty supersedes all prior warranties. To qualify for warranty service, you must (a) notify Broan-NuTone LLC at one of the addresses or telephone number stated below, (b) give the model number and part identification and (c) describe the nature of any defect in the product or part. -
Page 14: Service Parts
SERVICE PARTS 64000 Series 10 11 HL0002 QTY (hood width) PART NUMBER DESCRIPTION 30” 36” 42” 48” BROAN ELITE LOGO V06750 SOCKET LAMP V02264 V02773 MALE CONNECTOR V02772 FEMALE CONNECTOR V03435 THERMOSTAT V03436 THERMOSTAT BRACKET V03501 SPEED CONTROLLER SPST SINGLE SWITCH FOR WARMING LAMP... - Page 15 SERVICE PARTS SINGLE BLOWER/ROUGH-IN (Model P5) HL0021 PART NUMBER DESCRIPTION V13296 ADAPTER AND DAMPER 3 ’’ x 10’’ V03500 AIR DEFLECTOR V12997 SINGLE BLOWER ROUGH-IN PLATE ASSEMBLY V03577 FOAM 1/2” x 1/2” x 12” V02160 CAPACITOR 15MFD V01869 MACHINE SCREW NO. 6-32 x 1/4” V01857 WIRE COVER V01582...
- Page 16 SERVICE PARTS DUAL BLOWER/ROUGH-IN (Model P8) PART NUMBER DESCRIPTION V14971 ADAPTER AND DAMPER 3 ” x 14’’ V13296 ADAPTER AND DAMPER 3 ” x 10’’ V03500 AIR DEFLECTOR V14975 DUAL BLOWER ROUGH-IN PLATE ASSEMBLY V03577 FOAM 1/2” x 1/2” x 12” V01582 LOCK NUT NO.