Baby Lock ellageo BLL Instruction And Reference Manual page 190

Problem
High-pitched sound while Dust or lint is caught in the feed dogs.
sewing
Pieces of thread are caught in the race (bobbin
case).
The upper threading is incorrect.
There are scratches on the race (bobbin case).
Cannot thread the needle The needle is not in the correct position.
The threading hook does not pass through the
eye of the needle.
The needle is installed incorrectly.
Thread tension is incorrect The upper threading is incorrect.
Bobbin is set incorrectly.
The thread or needle is not suitable for the type
of fabric being sewn.
The presser foot holder is not attached
correctly.
The thread tension is set incorrectly.
Character pattern does not The wrong presser foot was used.
sew out correctly
Pattern adjustment settings were set incorrectly.
A stabilizer material was not used on lightweight
fabrics or stretch fabrics.
The thread tension is set incorrectly.
Embroidery pattern does The thread is tangled.
not sew out correctly
The fabric is incorrectly hooped in the embroidery
frame (fabric was loose, etc.).
A stabilizer material was not attached.
There was an object placed near the machine,
and the carriage or embroidery frame hit the
object during sewing.
Fabric outside of the frame edges interferes with
the sewing arm, so the embroidery unit cannot
move.
The fabric is too heavy, so the embroidery unit
cannot move freely.
Fabric is hanging off the table.
The fabric is snagged or caught on something.
Embroidery frame was removed during sewing
(for example, to reset the bobbin). The presser
foot was bumped or moved while removing or
attaching the embroidery frame, or the
embroidery unit was moved.
Cause
Remove the dust or lint.
Clean the race (bobbin case).
Check the procedure for threading the machine
and rethread it correctly.
Replace the race (bobbin case), or consult your
authorized retailer.
Press the "Needle Position" button to raise the
needle.
Press the "Needle Position" button to raise the
needle.
Reinstall the needle correctly.
Check the procedure for threading the machine
and rethread it correctly.
Reset the bobbin thread correctly.
Check the table of fabric, thread and needle
combinations, and select the appropriate
combination.
Reattach the presser foot holder correctly.
Adjust the thread tension.
Attach the correct presser foot.
Correct the pattern adjustment settings.
Attach a stabilizer material.
Adjust the thread tension.
Use scissors, etc., to cut the tangled thread and
remove it from the race (bobbin case), etc.
If the fabric is not stretched tight in the frame, the
pattern may be sewn incorrectly or there may be
shrinkage of the pattern. Hoop the fabric correctly
in the frame.
Always use stabilizer material, especially with
stretch fabrics, lightweight fabrics, fabrics with a
coarse weave, or fabrics that often cause pattern
shrinkage. Contact your authorized retailer for
the proper stabilizer.
If the frame bumps something during sewing, the
pattern will turn out poorly. Do not place anything
in the area where the frame may bump it during
sewing.
Rehoop the fabric in the embroidery frame so
that excess fabric is away from the sewing arm,
and rotate the pattern 180 degrees.
Place a thick book or similar object under the arm
head to lightly lift the heavy side and keep it level.
If fabric is hanging off the table while
embroidering, the embroidery unit will not move
freely. Position the fabric so that it does not hang
off the table or hold the fabric to keep it from
dragging.
Stop the machine, and then correctly position the
fabric so that it does not get caught or snagged.
If the presser foot is bumped or the embroidery
unit is moved during sewing, the pattern will not
turn out correctly. Be careful when removing or
reattaching the embroidery frame during sewing.
TROUBLESHOOTING
Solution Page
184
184
29
−
11
11
35
29
27
37
68
45
201
98
129
45
−
131
129
−
131
7
−
142
−
145
189