Page 1 PT Cruiser 2 0 1 0 O W N E R ’ S M A N U A L...
Page 2: Introduction
TABLE OF CONTENTS SECTION PAGE ............3 INTRODUCTION .
Page 4: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Vehicle Identification Number ....6 How To Use This Manual .
Page 5: Introduction
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech- LLC vehicle. Be assured that it represents precision nicians and genuine MOPAR parts, and cares about workmanship, distinctive styling, and high quality - all your satisfaction.
Page 6 INTRODUCTION 5...
Page 7: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
Page 8: Vehicle Modifications/Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Sentry Key — If Equipped ....15 Ignition Key Removal .
Page 11 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Keyless Entry (RKE) ....20 Power Windows ..... . . 31 To Unlock The Doors And Liftgate .
Page 12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Enhanced Seat Belt Use Reminder System Transporting Pets ..... 72 (BeltAlert ) ......44 Engine Break-In Recommendations .
Page 13: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key Removal The authorized dealer that sold you your new vehicle has Place the shift lever in PARK and make sure that the shift the key code numbers for your vehicle locks. These lever knob pushbutton has returned to the outward numbers can be used to order duplicate keys from your position.
Page 14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 key to the right slightly, then remove the key as de- scribed. If a malfunction occurs, the system will trap the key in the ignition cylinder to warn you that this safety feature is inoperable.
Page 15: Locking Doors With A Key
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE STEERING WHEEL LOCK — IF EQUIPPED CAUTION! Your vehicle may be equipped with a passive steering wheel lock. This lock prevents steering the vehicle with- An unlocked vehicle is an invitation to thieves. out the ignition key.
Page 16: Automatic Transaxle Ignition Interlock System - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 disengage it. If you turned the wheel to the left to engage The Sentry Key Immobilizer System does not need to be the lock, turn the wheel slightly to the left to disengage it. armed or activated.
Page 17: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE longer than 10 seconds), a fault has been detected in the CAUTION! electronics and the vehicle should be serviced as soon as possible by an authorized dealer. Always remove Sentry Keys from the vehicle and lock all doors when leaving the vehicle unattended.
Page 18: Sentry Key Programming
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Sentry Key Programming 4. Insert a blank Sentry Key into the ignition switch. If you have two valid Sentry Keys , you can program Turn the ignition switch to the ON position within new Sentry Keys to the system by performing the 60 seconds.
Page 19: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE your vehicle. The remaining keys must then be repro- If something triggers the Vehicle Security Alarm, it signal grammed. All vehicle keys must be taken to the autho- for about 18 minutes. For the first three minutes the horn rized dealer at the time of service to be reprogrammed.
Page 20: To Disarm The Alarm
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Vehicle Security Alarm is arming. During this period, if a Security System Manual Override door is opened, the ignition switch is turned ON, or the The Vehicle Security Alarm will not arm if you lock the power door locks are unlocked by either the power door doors using the manual door lock plunger.
Page 21: To Unlock The Doors And Liftgate
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY (RKE) NOTE: The line of transmission must not be blocked This system allows you to lock or unlock the doors and with metal objects. liftgate, or activate the Panic Alarm from distances ap- To Unlock the Doors and Liftgate proximately 66 ft (20 m) using a hand-held RKE trans- Press and release the UNLOCK button on the RKE...
Page 22: To Lock The Doors And Liftgate
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 EVIC-equipped vehicles refer to “Electronic Vehicle In- Security Alarm. Opening a door with the Security Alarm formation Center (EVIC)/Personal Settings (Customer- activated will cause the alarm to sound. Press the UN- Programmable Features)” in “Understanding Your In- LOCK button to deactivate the Security Alarm.
Page 23: To Turn Off "Flash Lights With Lock
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. While the LOCK button is pressed (after four seconds), 3. Test the “Flash Lights with Lock” feature while out- press the PANIC button. Release both buttons. side of the vehicle by pressing the LOCK button on the RKE transmitter with the ignition in the LOCK position, The “Sound Horn on Lock”...
Page 24: To Program Additional Transmitters
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Using The Panic Alarm total of eight RKE transmitters can be programmed to To turn the Panic Alarm feature ON or OFF, press and your vehicle through the use of a currently-programmed hold the PANIC button on the RKE transmitter for at RKE transmitter.
Page 25 24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Enter your vehicle and close all doors. 9. Using the RKE transmitter to be programmed, press and release both the LOCK and UNLOCK buttons, 3. Fasten your seatbelt. (Fastening the seatbelt will cancel simultaneously.
Page 26: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 General Information If your RKE transmitter fails to operate from a normal This device complies with Part 15 of the FCC rules and distance, check for these two conditions: RSS 210 of Industry Canada. Operation is subject to the 1.
Page 27: Door Locks
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. If the RKE transmitter is equipped with a screw, 2. Remove and replace the battery. Avoid touching the remove the screw. With the RKE transmitter buttons new battery with your fingers. Skin oils may cause facing down, use a flat blade to pry the two halves of the battery deterioration.
Page 28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 WARNING! • For personal security and safety in the event of an accident, lock the vehicle doors while you drive, when you park, and when leaving the vehicle. • When leaving the vehicle, always remove the key from the ignition lock, and lock your vehicle.
Page 29: Power Door Locks
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Power Door Locks Auto Lock — If Equipped A door lock switch is on each front door panel. Press The doors will lock automatically on vehicles with power either switch to lock or unlock the doors. door locks if all of the following conditions are met: 1.
Page 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 For vehicles not equipped with the EVIC, the Auto Lock 3. The shift lever is in NEUTRAL or PARK. can be enabled or disabled by performing the following 4. The driver door is opened. procedure: 5.
Page 31: Child Protection Door Lock System - If Equipped
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Press the power door UNLOCK switch to unlock the doors. 4. Verify reprogramming by driving the vehicle. NOTE: Use the Auto Lock and Auto Unlock features in accordance with local laws. Child Protection Door Lock System —...
Page 32: Power Windows
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 NOTE: For emergency exit with the system engaged, move the lock plunger up (UNLOCKED position), roll down the window and open the door with the outside door handle. POWER WINDOWS The power window switches are located on the instru- ment panel above the radio.
Page 33: Auto-Down Feature
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Rear Window Switches WARNING! There are also rear passenger window switches located at the rear of the center console. Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches.
Page 34: Wind Buffeting
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Wind Buffeting To open the unlocked liftgate, squeeze the liftgate release Wind buffeting can be described as the perception of touch pad located on the backside of the liftgate handle, pressure on the ears or a helicopter-type sound in the and pull the liftgate open with one fluid motion.
Page 35: Occupant Restraints
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE OCCUPANT RESTRAINTS WARNING! Some of the most important safety features in your • Driving with the liftgate open can allow poison- vehicle are the restraint systems. These include: ous exhaust gases into your vehicle. You and your •...
Page 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 • All seat belt systems (except the driver’s) include Please pay close attention to the information in this Automatic Locking Retractors (ALRs), which lock the section. It tells you how to use your restraint system seat belt webbing into position by extending the belt properly, to keep you and your passengers as safe as all the way out and then adjusting the belt to the...
Page 37: Lap/Shoulder Belts
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and they WARNING! can reduce the seriousness of injuries in a collision. Some • It is dangerous to ride in a cargo area, inside or of the worst injuries happen when people are thrown from the vehicle.
Page 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Lap/Shoulder Belt Operating Instructions WARNING! (Continued) 1. Enter the vehicle and close the door. Sit back and • Wearing your belt in the wrong place could make adjust the seat. your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out 2.
Page 39 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! A shoulder belt placed behind you will not protect you from injury during a collision. You are more likely to hit your head in a collision if you do not wear your shoulder belt. The lap and shoulder belt are meant to be used together.
Page 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 WARNING! • A belt that is worn under your arm is dangerous. Your body could strike the inside surfaces of the vehicle in a collision, increasing head and neck injury. A belt worn under the arm can cause internal injuries.
Page 41 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your WARNING! abdomen. To remove slack in the lap belt portion, pull up • A lap belt worn too high can increase the risk of on the shoulder belt.
Page 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 WARNING! WARNING! • A belt that is buckled into the wrong buckle will A frayed or torn belt could rip apart in a collision and not protect you properly. The lap portion could leave you with no protection.
Page 43: Lap/Shoulder Seat Belt Untwisting Procedure
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the rear seatback is properly latched and the rear Lap/Shoulder Seat Belt Untwisting Procedure center lap/shoulder belt still cannot be pulled out, the Use the following procedure to untwist a twisted lap/ Automatic-Locking Retractor (ALR) system may be shoulder belt.
Page 44: Adjustable Upper Shoulder Seat Belt Anchorage
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 Adjustable Upper Shoulder Seat Belt Anchorage As a guide, if you are shorter than average, you will In the front seat, the shoulder belt can be adjusted prefer a lower position, and if you are taller than average upward or downward to position the belt away from you will prefer a higher position.
Page 45: Seat Belt Pretensioners - If Equipped
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Engage The Automatic Locking Mode by assuring that the belt is tight about the occupant early in a collision. Pretensioners work for all size occupants, 1. Buckle the combination lap and shoulder belt. including those in child restraints.
Page 46: Seat Belts And Pregnant Women
Seat Belt Reminder Light for 96 seconds or rized dealer. until the driver’s or front passenger’s seat belt is buckled. • Chrysler Group LLC does not recommend deactivat- BeltAlert will be reactivated if the driver’s or passen- ing BeltAlert .
Page 47: Seat Belt Extender
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Extender Supplemental Restraint System (SRS) — Airbag If a seat belt is too short even when fully extended and This vehicle has Advanced Front Airbags for both the when the adjustable upper shoulder belt anchorage (if driver and front passenger as a supplement to the seat equipped) is in its lowest position, your authorized belt restraint systems.
Page 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 The Advanced Front Airbags have a multistage inflator design. This allows the airbag to have different rates of inflation based on the severity and type of collision. This vehicle may be equipped with driver and/or front passenger seat track position sensors that may adjust the inflation rate of the Advanced Front Airbags based upon seat position.
Page 49: Advanced Front Airbag Features
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Occupant Classification System (OCS) Airbag System Components Your vehicle may be equipped with the following airbag • Occupant Classification Module (OCM) system components: • Passenger Airbag Disable (PAD) Indicator Light • Occupant Restraint Controller (ORC) •...
Page 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 Supplemental Seat-Mounted Side Airbags (SAB) WARNING! Supplemental Seat-Mounted Side Airbags provide en- • No objects should be placed over or near the airbag hanced protection to help protect an occupant during a side impact.
Page 51 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When the airbag deploys, it opens the seam between the Along with seat belts and pretensioners, Advanced Front front and side of the seat’s trim cover. Each airbag Airbags work with the knee bolsters to provide improved deploys independently, that is a left side impact may protection for the driver and front passenger.
Page 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 Children that are not big enough to wear the vehicle seat The driver and front passenger seats should be moved belt properly (refer to “Child Restraints”) should be back as far as practical to allow the Advanced Front secured in the rear seat in child restraints or belt- Airbags room to inflate.
Page 53: Airbag Deployment Sensors And Controls
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Deployment Sensors and Controls WARNING! Occupant Restraint Controller (ORC) • Relying on the airbags alone could lead to more The ORC is part of a Federally regulated safety system severe injuries in a collision. The airbags work required for this vehicle.
Page 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 The Advanced Front Airbags will not deploy in all frontal The ORC monitors the readiness of the electronic parts of collisions, including some that may produce substantial the airbag system whenever the ignition switch is in the vehicle damage —...
Page 55 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE it turns on the Airbag Warning Light either momentarily Driver and Passenger Airbag Inflator Units or continuously. A single chime will sound if the light The Driver and Passenger Airbag Inflator Units are comes on again after initial startup.
Page 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Passenger Airbag Disable (PAD) Indicator Light The PAD indicator light should not be illumi- The (PAD) Indicator Light (an amber light located in the nated when an adult passenger is properly center of the instrument panel) tells the driver and front seated in the front passenger seat.
Page 57 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Drivers and adult passengers should verify that the PAD WARNING! Indicator Light is not illuminated when an adult is riding in the front passenger seat. If an adult occupant’s weight Never place a rear facing infant seat in front of an is transferred to another part of the vehicle (like the door airbag.
Page 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 If there is a fault present in the Airbag system, the Airbag the measurements made by the seat weight sensors. The Warning Light (a red light located in the center of the OCM communicates with the ORC.
Page 59 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The ORC monitors the readiness of the electronic parts of Front and Side Impact Sensors the airbag system whenever the ignition switch is in the In front and side impacts, impact sensors can aid the START or ON positions.
Page 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 • Turn on the interior lights, which remain on as long as floor. They are not caused by contact with chemicals. the battery has power or until the ignition key is They are not permanent and normally heal quickly. removed.
Page 61 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Maintaining Your Airbag System WARNING! WARNING! Deployed airbags and seat belt pretensioners cannot protect you in another collision. Have the airbags, • Modifications to any part of the airbag system seat belt pretensioners, and the front passenger seat could cause it to fail when you need it.
Page 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Airbag Warning Light WARNING! (Continued) You will want to have the airbags ready to • Do not attempt to modify any part of your ad- inflate for your protection in a collision. While vanced airbag system.
Page 63: Event Data Recorder (Edr)
Chrysler Group LLC and others to learn more speed deceleration data or change in velocity during about the possible causes of crashes and associated and/or after airbag deployment or near-deployment.
Page 64 Confidential • Vehicle speed data will not be disclosed by Chrysler Group LLC to any third party except when: • Engine RPM • Brake switch status...
Page 65: Child Restraints
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Pedal position WARNING! • And other parameters depending vehicle In a collision, an unrestrained child, even a tiny baby, configuration can become a projectile inside the vehicle. The force Child Restraints required to hold even an infant on your lap could Everyone in your vehicle needs to be buckled up all the become so great that you could not hold the child, no...
Page 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 • Safety experts recommend that children ride infant carriers do, so they can be used rearward-facing rearward-facing in the vehicle until they are at least by children who weigh more than 9 kg (20 lbs) but are one year old and weigh at least 20 lbs (9 kg).
Page 67 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The belt-positioning booster seat is for children weigh- WARNING! ing more than 40 lbs (18 kg), but who are still too small • Improper installation can lead to failure of an to fit the vehicle’s seat belts properly.
Page 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Here are some tips on getting the most out of your child restraint so that it is not necessary to use a locking clip. restraint: If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will •...
Page 69 68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If the belt still can’t be tightened, or if pulling and retractor. Allow the belt to return into the retractor, pushing on the restraint loosens the belt, disconnect pulling on the excess webbing to tighten the lap portion the latch plate from the buckle, turn the latch plate around the child restraint.
Page 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 the outboard positions only. Regardless of the specific type of lower attachment, NEVER install LATCH- compatible child seats such that two seats share a com- mon lower anchorage. If you are installing LATCH- compatible child restraints in adjacent rear seating positions, you can use the LATCH anchors or the vehi- cle’s seat belt for the outboard position, but you must use...
Page 71 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE provide add-on tether strap kits for some of their older restraint installation, instead of tucking the seat belt products. Tether anchorage kits are also available for behind the child restraint, route the seat belt through the most older vehicles.
Page 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 In general, you will first loosen the adjusters on the lower Not all child restraint systems will be installed as we and tether straps so that you can more easily attach the have described here.
Page 73: Transporting Pets
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Children too Large for Booster Seats Transporting Pets Children who are large enough to wear the shoulder belt Airbags deploying in the front seat could harm your pet. comfortably, and whose legs are long enough to bend An unrestrained pet will be thrown about and possibly over the front of the seat when their back is against the injured, or injure a passenger during panic braking or in...
Page 74: Safety Tips
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 While cruising, brief full-throttle acceleration within the SAFETY TIPS limits of local traffic laws, contributes to a good break-in. Transporting Passengers Wide-open throttle acceleration in low gear can be detri- NEVER TRANSPORT PASSENGERS IN THE CARGO mental and should be avoided.
Page 75: Exhaust Gas
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If it is necessary to sit in a parked vehicle with the engine WARNING! (Continued) running, adjust your heating or cooling controls to force • Be sure everyone in your vehicle is in a seat and outside air into the vehicle.
Page 76: Safety Checks You Should Make Inside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 inspect the exhaust system each time the vehicle is raised authorized dealer. If the light stays on, flickers, or comes for lubrication or oil change. Replace as required. on while driving, have the system checked by an autho- rized dealer.
Page 77 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! WARNING! (Continued) • Check mounting of mats on a regular basis. Al- Pedals that cannot move freely can cause loss of ways properly reinstall and secure floor mats that vehicle control and increase the risk of serious per- have been removed for cleaning.
Page 78: Periodic Safety Checks You Should Make Outside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 Periodic Safety Checks You Should Make Outside Door Latches the Vehicle Check for positive closing, latching, and locking. Tires Fluid Leaks Examine tires for excessive tread wear and uneven wear Check area under vehicle after overnight parking for fuel, patterns.
Page 80: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors ......82 Six-Way Power Seat With Manual Recliner — If Equipped .
Page 81 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Open And Close The Hood ... . . 99 Windshield Wiper Operation ... . 106 Intermittent Wiper System .
Page 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Using Electronic Speed Control On Hills ..114 Center Console/Armrest Storage Bin ..126 Storage Pockets ..... 128 Garage Door Opener —...
Page 83: Mirrors
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of the vehicle).
Page 84: Outside Mirror - Passenger Side
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Outside Mirror — Passenger Side (Left), O (Center) or R (Right) position. After selecting the Adjust the convex outside mirror so you can just see the mirror, move the knob in the same direction you want the side of your vehicle in the part of the mirror closest to the mirror to move.
Page 85: Illuminated Vanity Mirrors - If Equipped
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirrors — If Equipped NOTE: • The driver vanity mirror will become inoperable when Your vehicle may be equipped with an illuminated vanity mirror located on the sun visor. To use the mirror, the vehicle alarm is enabled.
Page 86: Seats
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 SEATS Seats are a primary part of the Occupant Restraint System of the vehicle. They need to be used properly for safe operation of the vehicle. WARNING! • DO NOT allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Page 87: Six-Way Power Seat With Manual Recliner - If Equipped
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! • Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust the seat only while the vehicle is parked.
Page 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 WARNING! • Do not ride with the seatback reclined so that the seat belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the re- cliner only when the vehicle is parked.
Page 89: Manual Lumbar - If Equipped
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! DO NOT place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path.
Page 90: Adjustable Head Restraints
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 To fold the seat forward, pull up on the recliner lever above the top of your ear. To raise a head restraint, pull located on the outboard side of the seat. up on the head restraint. To lower a head restraint, push in the button that is part of the head restraint rod guide, and push down on the head restraint.
Page 91: Heated Seats - If Equipped
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped an additional 30 minutes of continuous operation. If The heaters provide the same heat level for both cushion Low-level heating is selected, the system automatically and seatback. The driver and front passenger seats are turns the heater and the indicator light off after 30 min- heated.
Page 92: Folding Rear Seat
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 WARNING! (Continued) • Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the seat heater to overheat. Sitting in a seat that has been overheated could cause serious burns due to the increased surface temperature of the seat.
Page 93 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: WARNING! • If the rear center lap/shoulder belt appears to be • Do not ride in any of the rear seating positions locked into place, check to verify that the seatback is fully latched.
Page 94: Tumbling Rear Seat
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 Tumbling Rear Seat WARNING! To provide additional storage in the cargo area, each rear seat can be tumbled forward. The rear center lap/shoulder belt is equipped with a lockout feature to ensure that the seatback is in the CAUTION! fully upright and locked position when occupied.
Page 95 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 1. Push and hold the button on the seatback and fold 2. Pull the release handle located on the outboard side of down the rear seatback. the seat. Lift up the seat and tumble the seat forward. Folding Rear Seat Button Tumbling Seat Release Strap...
Page 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 3. Attach the tether, located at the base of the seat When returning the seatback to its upright position, cushion, onto the hook bar on the center trim panel to make sure that the seat latches are engaged. You should hold the seat in place.
Page 97: Rear Seat Removal
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Seat Removal 2. Pull the release lever located on the outboard side of The rear seats can be removed to provide more cargo the seat. Lift up the seat and tumble the seat forward. space.
Page 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 3. Lift up the release levers to disengage the seat from the NOTE: Small rollers on the bottom of the folded seat floor attachments. and a handle at the top allow the seat to be easily moved when removed from the vehicle.
Page 99: Emergency Seatback Release
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE EMERGENCY SEATBACK RELEASE glow-in-the-dark lever attached to the left rear seatback latching mechanism. Refer to “Cargo Area Features” in WARNING! “Understanding the Features of Your Vehicle” for further information. Do not allow children to have access to the liftgate area with the rear shelf panel in position 1 (Top) or position 2 (Middle), either by climbing into the liftgate from outside, or through the inside of the...
Page 100: To Open And Close The Hood
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 NOTE: Make sure that the elastic loop is around the emergency release handle at all times. If the handle is pulled downward, entirely through the elastic loop, the handle will not return to its original position and the seatback may not operate properly.
Page 101 100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Move the safety latch, located under the front edge of CAUTION! the hood, slightly to the right of center and raise the hood. To prevent possible damage, do not slam the hood to close it.
Page 102: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 LIGHTS Headlights and Parking Lights Turn the end of the multifunction lever to the first detent Multifunction Lever for parking lights and instrument panel lights. Turn to The multifunction lever controls the operation of the the second detent for headlight operation.
Page 103: Lights-On Reminder
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To change the brightness of the instrument panel lights, Rotate the center portion of the lever upward to the next rotate the center portion of the multifunction lever up or detent position to brighten the odometer and radio when down.
Page 104: High/Low Beam Switch
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 High/Low Beam Switch Push the multifunction lever away from you to switch the headlights to high beams. Pull the lever toward you to switch the headlights back to low beams. Flash-to-Pass You can signal another vehicle with your headlights by lightly pulling the multifunction lever toward the steer- ing wheel.
Page 105: Turn Signals
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turn Signals NOTE: • If either light remains on and does not flash, or there is Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show a very fast flash rate, check for a defective outside light proper operation of the front and rear turn signal lights.
Page 106: Map/Reading Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 NOTE: The Daytime Running Lights will turn off automatically when a turn signal is in operation and turn on again when the turn signal is not operating. Map/Reading Lights These lights are mounted between the sun visors above the rearview mirror.
Page 107: Windshield Wipers And Washers
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS Windshield Wiper Operation The windshield wiper/washer control lever is located on Rotate the end of the lever upward to the LO position for the right side of the steering column. The front wipers are low-speed wiper operation.
Page 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 NOTE: The wipers will automatically return to the CAUTION! (Continued) “park” position if you turn OFF the ignition switch while • Always remove any buildup of snow that prevents they are operating. The wipers will resume operation the windshield wiper blades from returning to the when you turn the ignition switch back to the ON park position.
Page 109: Intermittent Wiper System
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Intermittent Wiper System Use the intermittent wiper system when weather condi- tions make a single wiping cycle with a variable pause between cycles desirable. Rotate the end of the wind- shield wiper/washer control lever to the first detent, and then turn the end of the lever to select the desired delay interval.
Page 110: Windshield Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 to a maximum of approximately 18 seconds between If you activate the washer while the wiper control is in cycles at vehicle speeds greater than 10 mph (16 km/h). the OFF position, the wipers will operate for two or three wipe cycles and then turn OFF.
Page 111: Mist Feature
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Mist Feature Headlights With Wipers (Available with Automatic Push downward on the windshield wiper/washer con- Headlights Only) trol lever to activate a single wipe cycle to clear the When this feature is active, the headlights will turn on windshield of road mist or spray from a passing vehicle.
Page 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Push down on the lever to unlock the steering column. WARNING! With one hand firmly on the steering wheel, move the steering column up or down, as desired. Pull up on the Do not adjust the steering column while driving. lever to lock the column firmly in place.
Page 113: Electronic Speed Control - If Equipped
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRONIC SPEED CONTROL — IF EQUIPPED NOTE: In order to ensure proper operation, the Elec- When engaged, Electronic Speed Control takes over the tronic Speed Control System has been designed to shut accelerator operation at approximately either 30 mph down if multiple Speed Control functions are operated (40 km/h ) or 35 mph (56 km/h) depending on the model simultaneously.
Page 114: To Set A Desired Speed
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 To Deactivate WARNING! A soft tap on the brake pedal, pulling the Electronic Speed Control lever toward CANCEL, or normal brake Leaving the Electronic Speed Control system on or clutch pressure while slowing the vehicle will deacti- when not in use is dangerous.
Page 115: To Accelerate For Passing
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tapping RESUME ACCEL once will result in a 2 mph Using Electronic Speed Control on Hills (3 km/h) speed increase. Each time the lever is tapped, NOTE: The Electronic Speed Control system maintains speed increases so that tapping the lever three times will speed up and down hills.
Page 116: Garage Door Opener - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 WARNING! Electronic Speed Control can be dangerous where the system cannot maintain a constant speed. Your ve- hicle could go too fast for the conditions, and you could lose control. An accident could be the result. Do not use Electronic Speed Control in heavy traffic or on roads that are winding, icy, snow-covered or slippery.
Page 117: Programming Homelink
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming HomeLink WARNING! Before You Begin • Your motorized door or gate will open and close If you have not trained any of the HomeLink buttons, while you are training the universal transceiver. erase all channels before you begin training.
Page 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 • After training a HomeLink channel, if the garage Place the handheld transmitter 1 to 3 in (3 to 8 cm) away from the HomeLink button you wish to program while door does not operate with HomeLink and the ga- keeping the indicator light in view.
Page 119 118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This can usually be found where the hanging antenna 6. Firmly press and release the LEARN or TRAINING wire is attached to the garage door opener motor. It is button. The name and color of the button may vary by NOT the button normally used to open and close the manufacturer.
Page 120: Gate Operator/Canadian Programming
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Using HomeLink Gate Operator/Canadian Programming To operate, press and release the programmed Canadian radio frequency laws require transmitter sig- HomeLink button. Activation will now occur for the nals to time-out (or quit) after several seconds of trans- trained device (i.e., garage door opener, gate operator, mission –...
Page 121: Security
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE successfully accepted the frequency signal. The indica- Troubleshooting Tips tor light will flash slowly and then rapidly when fully If you are having trouble programming HomeLink , here are some of the most common solutions: trained.
Page 122: Power Sunroof - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 2. This device must accept any interference that may be received including interference that may cause undesired operation. NOTE: • The transmitter has been tested and it complies with FCC and IC rules. Changes or modifications not expressly approved by the party responsible for com- pliance could void the user’s authority to operate the device.
Page 123: Express-Open Feature
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press and hold the button in the center of the sunroof The sunshade can be opened manually. It will also open switch to open the vent. The sunroof can be stopped at as the sunroof opens. The sunshade cannot be closed if any position between closed and full vent.
Page 124: Wind Buffeting
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Sunroof Maintenance WARNING! (Continued) Use only a non-abrasive cleaner and a soft cloth to clean • Do not allow small children to operate the sun- the glass panel. roof. Never allow your fingers, other body parts, or any object to project through the sunroof opening.
Page 125 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE This outlet will accept a cigar lighter unit, which is part of the optional Smokers Package. To preserve the heating element of the cigar lighter unit, do not hold the lighter in the heating position. As a child safety precaution, this power outlet is powered by the ignition switch, only when the switch is in the ON or ACC position.
Page 126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 WARNING! CAUTION! • Many accessories that can be plugged in draw To avoid serious injury or death: • Only devices designed for use in this type of power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
Page 127: Storage
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE STORAGE Push the upper button on the front of the armrest to raise the upper cover. Center Console/Armrest Storage Bin The center console provides a sliding armrest with two storage compartments under the lid. Upper Storage Button Sliding Armrest...
Page 128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Inside is an area to store a cellular phone and other Push the lower button on the front of the armrest, and miscellaneous items. raise the armrest for access to the lower storage bin. Upper Storage Bin Lower Storage Button...
Page 129: Storage Pockets
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The lower storage area can be used for storing up to six CONSOLE FEATURES compact discs (CDs) and other miscellaneous items. The console has two front cupholders, a removable coin holder, 12 Volt power outlet and a front storage tray. There are three additional cupholders;...
Page 130: Rear Shelf Panel - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 NOTE: The liftgate may be opened or closed with the CAUTION! (Continued) rear cargo shelf panel in position 1, position 2, position 3 • Accessories that draw higher power (i.e., coolers, or position 4. vacuum cleaners, lights, etc.), will discharge the battery even more quickly.
Page 131: Position 1 (Top)
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position 1 (Top) WARNING! Insert the front outboard corners of the shelf panel into the top guides and slide forward. Press down on the back Do not load objects on the shelf in position 1 (top). In of the shelf panel to lock it into place.
Page 132: Position 3 (Floor)
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 WARNING! Do not load objects over 100 lbs (45 kg) in position 2 (middle). Failure to follow this warning could cause the shelf to collapse resulting in personal injury. Position 3 (Floor) Insert the front outboard corners of the shelf panel into the bottom guides and slide forward.
Page 133: Position 4 (Vertical)
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Position 4 (Vertical) WARNING! Insert the front outboard corners of the shelf panel into the vertical guides behind the rear seatbacks near the When in the vertical position, the rear shelf panel floor and slide downward. Push the shelf panel forward should not be used as a barrier for large objects in the to lock it by aligning the vertical guide with the rubber cargo area with the seatbacks folded down.
Page 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 2. Twist the knob on the underside of the panel and lower the shelf leg. Rear Shelf Panel Position 5 WARNING! Rear Shelf Leg Release Knob Do not load objects over 100 lbs (45 kg) in position 5 3.
Page 135: Rear Window Features
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rotate the switch upward to the “on” position will activate the rear wiper. Rear Window Wiper/Washer The rear window wiper/washer control is located on the Rotate the switch upward to the “washer” position right side of the steering column.
Page 136: Rear Window Defroster
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Rear Window Defroster CAUTION! The rear window defroster button is located on the • Turn the rear wiper off when driving through an climate control panel. Press this button to turn on the rear window defroster and the heated outside mirrors automatic car wash.
Page 137 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements.
Page 138 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....140 Trip Odometer (ODO) ....158 Instrument Cluster —...
Page 139 138 UNDERSTANDING YOUR INSTRUMENT PANEL Compass Variance ....162 Operating Instructions — Uconnect™ Phone — If Equipped ..... . 175 Tire Pressure Monitor (TPM) .
Page 140 UNDERSTANDING YOUR INSTRUMENT PANEL 139 PTY Button Scan ....178 Radio Operation And Cellular Phones ..180 PTY Button Seek .
Page 141: Instrument Panel Features
140 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT PANEL FEATURES 1 — Air Vent 5 — Glove Compartment 9 — Storage Cubby 2 — Instrument Cluster 6 — Power Windows 10 — Lower Switch Bank 3 — Analog Clock 7 — Radio 11 —...
Page 142: Instrument Cluster - Base
UNDERSTANDING YOUR INSTRUMENT PANEL 141 INSTRUMENT CLUSTER — BASE...
Page 143: Instrument Cluster - Premium
142 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — PREMIUM...
Page 144: Instrument Cluster Descriptions
UNDERSTANDING YOUR INSTRUMENT PANEL 143 INSTRUMENT CLUSTER DESCRIPTIONS CAUTION! 1. Fuel Gauge Driving with a hot engine cooling system could When the ignition switch is in the ON position, the damage your vehicle. If temperature gauge reads “H” pointer will show the level of fuel remaining in the fuel pull over and stop the vehicle.
Page 145 144 UNDERSTANDING YOUR INSTRUMENT PANEL 6. Shift Lever Indicator WARNING! The Shift Lever Indicator is self-contained within the instrument cluster. It displays the gear position of the A hot engine cooling system is dangerous. You or automatic transmission. others could be badly burned by steam or boiling coolant.
Page 146 UNDERSTANDING YOUR INSTRUMENT PANEL 145 As an added safety feature, your vehicle has been Your vehicle has also been equipped with a TPMS equipped with a Tire Pressure Monitoring System malfunction indicator to indicate when the system is not (TPMS) that illuminates a low tire pressure telltale when operating properly.
Page 147 146 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: U.S. Federal regulations require that upon trans- CAUTION! fer of vehicle ownership, the seller certify to the pur- chaser the correct mileage that the vehicle has been The TPMS has been optimized for the original driven.
Page 148 UNDERSTANDING YOUR INSTRUMENT PANEL 147 Vehicle Odometer Messages gASCAP Message When the appropriate conditions exist, the following If the vehicle diagnostic system determines that the fuel messages will display in the odometer: filler cap is loose, improperly installed, or damaged, the words “gASCAP”...
Page 149 148 UNDERSTANDING YOUR INSTRUMENT PANEL 9. Cruise Indicator — If Equipped Certain conditions such as a loose or missing gas cap, This indicator shows that the Electronic Speed poor fuel quality, etc., may illuminate the MIL after Control system is ON. engine start.
Page 150 UNDERSTANDING YOUR INSTRUMENT PANEL 149 12. Charging System Light WARNING! This light shows the status of the electrical charg- ing system. The light should come on when the A malfunctioning catalytic converter, as referenced ignition switch is first turned ON and remain on briefly above, can reach higher temperatures than in normal as a bulb check.
Page 151 150 UNDERSTANDING YOUR INSTRUMENT PANEL 14. Electronic Stability Program (ESP) Indicator Light hydraulic system malfunction or that a problem with the / Traction Control System (TCS) Indicator Light Brake Booster has been detected by the Anti-Lock Brake If this indicator light flashes during accelera- System (ABS) / Electronic Stability Program (ESP) sys- tion, apply as little throttle as possible.
Page 152 UNDERSTANDING YOUR INSTRUMENT PANEL 151 NOTE: The light may flash momentarily during sharp Operation of the Brake Warning Light can be checked by cornering maneuvers, which change fluid level condi- turning the ignition switch from the OFF position to the tions.
Page 153 152 UNDERSTANDING YOUR INSTRUMENT PANEL and the chime will sound. Refer to “Occupant Restraints” service. Refer to “If Your Engine Overheats” in “What To in “Things To Know Before Starting Your Vehicle” for Do In Emergencies” for further information. further information. 18.
Page 154 UNDERSTANDING YOUR INSTRUMENT PANEL 153 21. Anti-Lock Brake (ABS) Light is started. If the light turns on while driving, stop the This light monitors the Anti-Lock Brake System vehicle and shut off the engine as soon as possible. A (ABS). The light will turn on when the ignition chime will sound for four minutes when this light turns switch is turned to the ON position and may stay on for as long as four seconds.
Page 155 154 UNDERSTANDING YOUR INSTRUMENT PANEL 24. High Beam Indicator 26. Compass Mini-Trip Computer (CMTC) or Electronic This indicator shows that the high beam head- Vehicle Information Center (EVIC) Display — If lights are on. Push the multifunction lever forward Equipped to switch the headlights to high beam, and pull toward On vehicles equipped with Electronic Vehicle Informa- yourself (normal position) to return to low beam.
Page 156: Compass Mini-Trip Computer (Cmtc) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 155 COMPASS MINI-TRIP COMPUTER (CMTC) — IF Compass Mini-Trip Computer Reset Button EQUIPPED CMTC Reset Button — Secondary Reset Button NOTE: The compass on your vehicle is self-calibrating, Press the left Compass/Temperature RESET button to eliminating the need to manually calibrate the compass. scroll through sub-menus (i.e., Trip Functions: AVG Fuel Economy, DTE Elapsed Time, and Units (US or Metric).
Page 157: Compass/Temperature Display
156 UNDERSTANDING YOUR INSTRUMENT PANEL Compass/Temperature Display Compass Variance Compass Variance is the difference between Magnetic North and Geographic North. To ensure compass accu- racy, the compass variance should be properly set accord- ing to the variance map for the zone where the vehicle will be driven.
Page 158 UNDERSTANDING YOUR INSTRUMENT PANEL 157 the zone, press and release the RESET button to incre- Calibrate the compass by driving slowly, under 5 mph ment the variance one step. Repeat as necessary, until the (8 km/h) in one or more complete circles in a area free desired variance is achieved.
Page 159: Odometer Display
158 UNDERSTANDING YOUR INSTRUMENT PANEL 3. Release the RESET button, then press and hold again These messages can be manually turned off by pressing (approximately 10 seconds), until the direction is dis- the right reset button (on the instrument cluster). played with the CAL indicator on continuously in the Trip Odometer (ODO) display.
Page 160: Electronic Vehicle Information Center (Evic) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 159 ELECTRONIC VEHICLE INFORMATION CENTER The Electronic Vehicle Information Center (EVIC) fea- (EVIC) – IF EQUIPPED tures a driver-interactive display that is located in the instrument cluster. The EVIC consists of the following: • System Status •...
Page 161: Evic Functions
160 UNDERSTANDING YOUR INSTRUMENT PANEL • Left/Right Rear Door Ajar (one or more, with a single When the appropriate conditions exist, the EVIC displays the following messages: chime, if speed is above 1 mph) • Turn Signal On (with a continuous warning chime) •...
Page 162: To Reset The Display
UNDERSTANDING YOUR INSTRUMENT PANEL 161 • Tire Pressure Monitor (TPM) displayed. To reset all resettable functions, press and release the EVIC button a second time within three • Personal Settings seconds of resetting the currently-displayed function (Reset ALL will be displayed during this three-second window).
Page 163: Distance To Empty (Dte)
162 UNDERSTANDING YOUR INSTRUMENT PANEL history information will be erased, and the averaging will FUEL text and a new DTE value will be displayed, based continue from where it was before the reset. on the current values in the DTE calculation and the current fuel tank level.
Page 164: Tire Pressure Monitor (Tpm)
UNDERSTANDING YOUR INSTRUMENT PANEL 163 2. Press and release the EVIC button several times until you have displayed the Personal Settings (Customer- Programmable Features) menu. 3. Press and release the EVIC button until “Compass Variance” and the current variance zone number displays in the EVIC.
Page 165: Personal Settings (Customer-Programmable Features)
164 UNDERSTANDING YOUR INSTRUMENT PANEL Personal Settings (Customer-Programmable NOTE: Uconnect™ language will not change using the Features) EVIC. Please refer “Language Selection” This allows the driver to set and recall features when the “Uconnect™ — If Equipped” for details. shift lever is in PARK (automatic transmission) or the Lock Doors Automatically at 15 MPH (24 km/h) vehicle is stopped (manual transmission).
Page 166 UNDERSTANDING YOUR INSTRUMENT PANEL 165 Remote Unlock Driver’s Door 1st Flash Lights On Lock When Driver’s Door 1st is selected, only the driver’s door When ON is selected, the front and rear turn signals will will unlock on the first press of the Remote Keyless Entry flash when the doors are locked or unlocked using the (RKE) transmitter UNLOCK button.
Page 167: Automatic Compass Calibration
166 UNDERSTANDING YOUR INSTRUMENT PANEL OFF. Opening a vehicle door will cancel this feature. Press and hold the EVIC button when in this display until Press and hold the EVIC button when in this display until US or METRIC appears, to make your selection. OFF, 45 sec, 5 min, or 10 min appears, to make your Automatic Compass Calibration selection.
Page 168: Manual Compass Calibration
UNDERSTANDING YOUR INSTRUMENT PANEL 167 NOTE: 2. Press and release the EVIC button several times until • A good calibration requires a level surface and an the EVIC displays the Personal Settings (Customer- environment free from large metallic objects such as Programmable Features) menu.
Page 169: Setting The Analog Clock
168 UNDERSTANDING YOUR INSTRUMENT PANEL SETTING THE ANALOG CLOCK SALES CODE REF — AM/FM/CD (SINGLE-DISC) To set the analog clock at the top center of the instrument RADIO WITH OPTIONAL Uconnect™ Multimedia panel, press and hold the button until the setting is (SATELLITE RADIO) AND Uconnect™...
Page 170: Operating Instructions - Radio Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 169 Operating Instructions — Radio Mode MODE Button (Radio Mode) Press the MODE button repeatedly to select between the NOTE: The ignition switch must be in the ON or ACC CD player and Satellite Radio (if equipped). position to operate the radio.
Page 171 170 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: In Hands-Free Phone (if equipped) mode, the Clock Setting Procedure MUTE button mutes the microphone. 1. Press and hold the TIME button until the hours blink. SCAN Button (Radio Mode) 2. Adjust the hours by turning the TUNE/AUDIO con- Pressing the SCAN button causes the tuner to search for trol.
Page 172 UNDERSTANDING YOUR INSTRUMENT PANEL 171 TUNE Control (Radio Mode) Press the rotary TUNE control a fourth time and “BAL” Turn the rotary TUNE control clockwise to increase or will display. Turn the TUNE control to the right or left to counterclockwise to decrease the frequency.
Page 173: Operating Instructions - Cd Mode
172 UNDERSTANDING YOUR INSTRUMENT PANEL selected within five seconds after pressing the SET but- Operating Instructions — CD Mode ton, the station will continue to play but will not be NOTE: The ignition switch must be in the ON or ACC stored into pushbutton memory.
Page 174 UNDERSTANDING YOUR INSTRUMENT PANEL 173 • If you insert a disc with the ignition ON and the radio SCAN Button (CD Mode) OFF, the CD will automatically be pulled into the CD Press this button to play the first 10 seconds of each track. player.
Page 175: Operating Instructions - Auxiliary Mode
174 UNDERSTANDING YOUR INSTRUMENT PANEL Press and hold the FF button to fast forward through the MP3 player, cassette player, or microphone and utilize tracks. Release the FF button to stop the fast forward the vehicle’s audio system to amplify the source and play feature.
Page 176: Operating Instructions - Uconnect™ Phone - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 175 second time and the sound from the speakers will return. RW/FF (Auxiliary Mode) Rotating the volume control or turning the ignition No function. OFF/ON will also return the sound from the speakers. RND/SET Button (Auxiliary Mode) SCAN Button (Auxiliary Mode) No function.
Page 177: Uconnect™ Multimedia (Satellite Radio) - If Equipped
176 UNDERSTANDING YOUR INSTRUMENT PANEL Uconnect™ Multimedia (SATELLITE RADIO) — IF 3. Your Vehicle Identification Number. EQUIPPED Electronic Serial Number/Sirius Identification Satellite radio uses direct satellite to receiver broadcast- Number (ESN/SID) ing technology to provide clear digital sound, coast to The Electronic Serial Number/Sirius Identification Num- coast.
Page 178: Selecting Uconnect™ Multimedia (Satellite) Mode In Ref, And Raq, Radios
UNDERSTANDING YOUR INSTRUMENT PANEL 177 ESN/SID Access With RAQ Radios Selecting Satellite Mode — RAQ Radio With the ignition switch in the ACCESSORY position and Press the MODE button repeatedly until the word SAT the radio OFF, press the CD Eject and TIME buttons appears in the display.
Page 179: Storing And Selecting Pre-Set Channels
178 UNDERSTANDING YOUR INSTRUMENT PANEL moving on to the next channel. The word SCAN will PTY Button SCAN appear in the display between each channel change. Press When the desired program type is obtained, press the the SCAN button a second time to stop the search. SCAN button within five seconds.
Page 180: Reception Quality
UNDERSTANDING YOUR INSTRUMENT PANEL 179 placed within the line of sight of the antenna will cause CD/DVD DISC MAINTENANCE decreased performance. Larger luggage items should be To keep a CD/DVD in good condition, take the following placed as far forward as possible. Do not place items precautions: directly on or above the antenna.
Page 181: Understanding Your Instrument Panel
180 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particu- CLIMATE CONTROLS lar disc, it may be damaged (i.e., scratched, reflective Climate Control Operation coating removed, a hair, moisture or dew on the disc) The Climate Control system allows you to balance the oversized, or have protection encoding.
Page 182 UNDERSTANDING YOUR INSTRUMENT PANEL 181 NOTE: The air conditioning system of your vehicle Mode Control (Air Direction) contains R-134a, a refrigerant that does not deplete the The Mode control allows you to ozone layer in the upper atmosphere. choose from several patterns of air distribution.
Page 183 182 UNDERSTANDING YOUR INSTRUMENT PANEL air goes to the floor outlets. This feature gives improved NOTE: The air conditioning compressor operates in comfort during sunny but cool conditions. both Mix and Defrost or a blend of these modes even if the A/C button has not been pressed and the indicator Floor lamp is off.
Page 184 UNDERSTANDING YOUR INSTRUMENT PANEL 183 NOTE: For maximum airflow to the rear seat passen- Fabric front fascia protectors may reduce airflow to the gers, the center instrument panel outlets can be aimed, so condenser, reducing air conditioning performance. that the left center outlet is directed toward the right rear Air Conditioning (A/C) —...
Page 185 184 UNDERSTANDING YOUR INSTRUMENT PANEL MAX A/C Circulation Control To quickly cool the vehicle interior Rotate this control to choose between follow the steps listed below: outside air intake or recirculation of the air inside the vehicle. A lamp will illuminate when you are in Recircula- tion mode.
Page 186: Operating Tips
UNDERSTANDING YOUR INSTRUMENT PANEL 185 Operating Tips Operating Tips...
Page 187 186 UNDERSTANDING YOUR INSTRUMENT PANEL Window Fogging Summer Operation Vehicle side windows tend to fog on the inside in mild, Vehicles must be protected with a high-quality antifreeze rainy or humid weather. To clear the windows, use the coolant to provide proper corrosion protection and to A/C, Panel and Blower controls.
Page 188 UNDERSTANDING YOUR INSTRUMENT PANEL 187 Side Window Demisters A side window demister outlet is at each end of the instrument panel. These nonadjustable outlets direct air toward the side windows when the system is in either the Floor, Mix, or Defrost mode. The air is directed at the area of the windows through which you view the outside mirrors.
Page 190: Starting And Operating
STARTING AND OPERATING CONTENTS Starting Procedures ....192 Brake/Transmission Interlock System ..195 Automatic Transmission ....192 Four-Speed Automatic Transmission .
Page 191 190 STARTING AND OPERATING Driving Through Water ....203 Tire Terminology And Definitions ..218 Flowing/Rising Water ....203 Tire Loading And Tire Pressure .
Page 192 STARTING AND OPERATING 191 Loose Fuel Filler Cap Message ... 243 Towing Tips ......257 Vehicle Loading .
Page 193: Starting Procedures
192 STARTING AND OPERATING STARTING PROCEDURES NOTE: You must press the brake pedal before shifting Before starting your vehicle, adjust your seat, adjust both out of PARK. inside and outside mirrors, and fasten your seat belts. Normal Starting Normal starting of either a cold or a warm engine does WARNING! not require pumping or pressing the accelerator pedal.
Page 194: Extreme Cold Weather (Below 20°F Or 29°C)
STARTING AND OPERATING 193 If The Engine Fails To Start WARNING! If the engine fails to start after you have followed the “Normal Starting” procedure, it may be flooded. Push Do not attempt to push or tow your vehicle to get it the accelerator pedal all the way to the floor and hold it started.
Page 195: After Starting
194 STARTING AND OPERATING AUTOMATIC TRANSMISSION CAUTION! WARNING! To prevent damage to the starter, do not crank the engine for more than 15 seconds at a time. Wait 10 to It is dangerous to move the shift lever out of PARK or 15 seconds before trying again.
Page 196: Key Ignition Park Interlock
STARTING AND OPERATING 195 Key Ignition Park Interlock CAUTION! This vehicle is equipped with a Key Ignition Park Inter- lock which requires the shift lever to be placed in PARK Damage to the transmission may occur if the follow- prior to rotating the key to the LOCK position. The key ing precautions are not observed: •...
Page 197: Four-Speed Automatic Transmission
196 STARTING AND OPERATING NOTE: If a malfunction occurs, the system will function Four-Speed Automatic Transmission normally, except you may be able to shift the vehicle from NOTE: Under extreme cold temperatures (-6°F (-21°C) PARK, without pressing the brake pedal. If this occurs and when in DRIVE, transmission operation may be obtain service from an authorized dealer as soon as briefly limited to only second gear operation.
Page 198: Gear Ranges
STARTING AND OPERATING 197 RESET Mode NOTE: Even if the transmission can be reset, it is The transmission is monitored electronically for abnor- recommended that you visit an authorized dealer at your mal conditions. If a condition is detected that could cause earliest possible convenience.
Page 199 198 STARTING AND OPERATING • Look at the shift indicator window on the console to WARNING! ensure it is in the PARK position. Unintended movement of a vehicle could injure • When engaged in PARK, you will not be able to move those in and near the vehicle.
Page 200 STARTING AND OPERATING 199 NEUTRAL When frequent transmission shifting occurs while using This range is used when vehicle is standing for pro- the DRIVE/OVERDRIVE range, such as when operating longed periods with engine running. Engine may be the vehicle under heavy loading conditions (in hilly started in this range.
Page 201: Autostick - If Equipped
200 STARTING AND OPERATING LOW — 1st you move the shift lever into the AutoStick position, it This range should be used for maximum engine braking can be moved from side to side. Moving the lever to the when descending steep grades. In this range, up shifts left (-) triggers a downshift and to the right (+) an upshift.
Page 202: General Information
STARTING AND OPERATING 201 • The transmission will automatically upshift from first You can move the shift lever in or out of the AutoStick mode at any time without taking your foot off the to second gear and from second to third gear when accelerator pedal.
Page 203: Driving On Slippery Surfaces
202 STARTING AND OPERATING • If the system detects powertrain overheating, the WARNING! transmission will revert to the automatic shift mode and remain in that mode until the powertrain cools off. Rapid acceleration on slippery surfaces is dangerous. Unequal traction can cause sudden pulling of the •...
Page 204: Driving Through Water
STARTING AND OPERATING 203 2. Slow down if the road has standing water or puddles. Flowing/Rising Water 3. Replace the tires when tread wear indicators first WARNING! become visible. Do not drive on or across a road or path where water 4.
Page 205 204 STARTING AND OPERATING CAUTION! CAUTION! (Continued) • Driving through standing water may cause dam- • Always check the depth of the standing water age to your vehicle’s drivetrain components. Al- before driving through it. Never drive through ways inspect your vehicle’s fluids (i.e., engine oil, standing water that is deeper than the bottom of transmission, axle, etc.) for signs of contamination the tire rims mounted on the vehicle.
Page 206: Power Steering
STARTING AND OPERATING 205 POWER STEERING WARNING! The standard power steering system will give you good • Driving through standing water limits your vehi- vehicle response and increased ease of maneuverability in tight spaces. The system will provide mechanical cle’s traction capabilities. Do not exceed 5 mph steering capability if power assist is lost.
Page 207: Power Steering Fluid Check
206 STARTING AND OPERATING system. This noise should be considered normal, and it checked if a leak is suspected, abnormal noises are does not in any way damage the steering system. apparent, and/or the system is not functioning as antici- pated.
Page 208: Parking Brake
STARTING AND OPERATING 207 If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied.
Page 209 208 STARTING AND OPERATING NOTE: WARNING! • When the parking brake is applied and the transmis- • Never use the PARK position as a substitute for sion is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound the parking brake.
Page 210: Brake System
STARTING AND OPERATING 209 with the engine off), the brakes will still function. How- WARNING! (Continued) ever, the effort required to brake the vehicle will be much • Always fully apply the parking brake when leav- greater than that required with the power system oper- ing your vehicle or it may roll and cause damage or ating.
Page 211: Anti-Lock Brake System (Abs) - If Equipped
210 STARTING AND OPERATING malfunction is caused by an internal leak, as the brake WARNING! fluid in the master cylinder drops, the “Brake Warning • Pumping of the ABS will diminish their effective- Light” will illuminate. ness and may lead to an accident. Pumping makes WARNING! the stopping distance longer.
Page 212 STARTING AND OPERATING 211 brakes. If the ABS light does not come on when the WARNING! (Continued) ignition switch is turned to the ON position, have the • The capabilities of an ABS-equipped vehicle must bulb repaired as soon as possible. never be exploited in a reckless or dangerous If both the “Brake Warning Light”...
Page 213: Traction Control System - If Equipped
212 STARTING AND OPERATING You also may experience the following when the brake WARNING! system goes into anti-lock: The ABS contains sophisticated electronic equip- • The ABS motor running (it may continue to run for a ment that may be susceptible to interference caused short time after the stop), by improperly-installed or high-output radio trans- •...
Page 214 STARTING AND OPERATING 213 • There is a Traction Control System malfunction; occurs the “TCS Indicator Light” located above the instrument cluster odometer will flash. The system oper- • The system has been automatically deactivated to ates at speeds below 35 mph (56 km/h). prevent damage to the brake system due to overheated brake temperatures.
Page 215: Tire Safety Information
214 STARTING AND OPERATING TIRE SAFETY INFORMATION NOTE: • P (Passenger) - Metric tire sizing is based on U.S. Tire Markings design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. •...
Page 216 STARTING AND OPERATING 215 • High flotation tire sizing is based on U.S. design Tires designed to this standard have the letter “T” molded into the sidewall preceding the size designa- standards and it begins with the tire diameter molded tion.
Page 217 216 STARTING AND OPERATING EXAMPLE: 15 = Rim diameter in inches (in) Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
Page 218: Tire Identification Number (Tin)
STARTING AND OPERATING 217 Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
Page 219: Tire Terminology And Definitions
218 STARTING AND OPERATING Tire Terminology and Definitions Term Definition B-Pillar The vehicle B-Pillar is a structural member of the body located between the front and rear door (of a four-door vehicle) running from the sill to the roof. Cold Tire Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
Page 220: Tire Loading And Tire Pressure
STARTING AND OPERATING 219 Tire Loading and Tire Pressure Tire and Loading Information Placard Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar. Tire and Loading Information Placard This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry 3) tire size designed for your vehicle...
Page 221 220 STARTING AND OPERATING Loading The combined weight of occupants, cargo/luggage and The vehicle maximum load on the tire must not exceed trailer tongue weight (if applicable) should never exceed the load carrying capacity of the tire on your vehicle. You the weight referenced here.
Page 222 STARTING AND OPERATING 221 available cargo and luggage load capacity is 650 lbs NOTE: • The following table shows examples on how to calcu- (295 kg) (since 5 x 150 = 750, and 1400 – 750 = 650 lbs [295 kg]). late total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations 5.
Page 223 222 STARTING AND OPERATING...
Page 224: Tires - General Information
STARTING AND OPERATING 223 Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause accidents. recommended load capacity for your vehicle.
Page 225 224 STARTING AND OPERATING Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the • Unequal tire pressures from one side of the ve- driver’s side “B” Pillar. hicle to the other can cause the vehicle to drift to Some vehicles may have Supplemental Tire Pressure the right or left.
Page 226 STARTING AND OPERATING 225 Tire pressures change by approximately 1 psi (7 kPa) per CAUTION! 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in After inspecting or adjusting the tire pressure, al- the Winter.
Page 227 226 STARTING AND OPERATING Tire Pressures for High-Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
Page 228 STARTING AND OPERATING 227 WARNING! CAUTION! Temporary-use spare tires are for emergency use Because of the reduced ground clearance, do not take only. With these tires, do not drive more than 50 mph your vehicle through an automatic car wash with the (80 km/h).
Page 229 228 STARTING AND OPERATING WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure some- one. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for more than 30 seconds continuously when you are stuck, and do not let anyone near a spinning wheel, no matter what the...
Page 230 STARTING AND OPERATING 229 Life Of Tire Replacement Tires The service life of a tire is dependent upon varying The tires on your new vehicle provide a balance of many factors including, but not limited to: characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure.
Page 231 230 STARTING AND OPERATING WARNING! WARNING! (Continued) • Failure to equip your vehicle with tires having • Do not use a tire, wheel size or rating other than adequate speed capability can result in sudden tire that specified for your vehicle. Some combinations failure and loss of vehicle control.
Page 232: Tire Chains
STARTING AND OPERATING 231 TIRE CHAINS Snow tires generally have lower speed ratings than what Due to limited clearance, tire chains are not recom- was originally equipped with your vehicle and should mended. not be operated at sustained speeds over 75 mph (120 km/h).
Page 233: Tire Pressure Monitoring System (Tpms)
232 STARTING AND OPERATING Refer to “Maintenance Schedule” for the proper mainte- TIRE PRESSURE MONITORING SYSTEM (TPMS) nance intervals. More frequent rotation is permissible if The TPMS will warn you of a low tire pressure based on desired. The reasons for any rapid or unusual wear the vehicle recommended cold placard pressure.
Page 234 STARTING AND OPERATING 233 TPMS will warn you of a low tire pressure if the tire For example, your vehicle may have a recommended pressure falls below the low-pressure warning limit for cold (parked for more than three hours) placard pressure any reason, including low temperature effects and natu- of 33 psi (227 kPa).
Page 235 234 STARTING AND OPERATING NOTE: CAUTION! • TPMS is not intended to replace normal tire care and maintenance, or to provide warning of a tire failure or The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and condition.
Page 236: Base System
STARTING AND OPERATING 235 • Seasonal temperature changes will affect tire pressure, Tire Pressure Monitoring Low Pressure Warnings and the TPMS will monitor the actual tire pressure in The TPMS Telltale Light will illuminate in the the tire. instrument cluster and a chime will sound when tire pressure is low in one or more of the four Base System active road tires.
Page 237 236 STARTING AND OPERATING will turn off when the fault condition no longer exists. A 2. If you install the compact spare tire in place of a road system fault can occur due to any of the following: tire that has a pressure below the low-pressure warning limit, upon the next ignition key cycle, a chime will 1.
Page 238: Fuel Requirements
STARTING AND OPERATING 237 active road tires. The vehicle may need to be driven for FUEL REQUIREMENTS up to 20 minutes above 15 mph (25 km/h) in order for the 2.4L Engine TPMS to receive this information. 2.4L engines are designed to meet all emis- General Information sion regulations and provide excellent fuel This device complies with part 15 of the FCC rules and...
Page 239 238 STARTING AND OPERATING The manufacturer supports the use of reformulated gaso- Problems that result from using methanol gasoline or E85 lines. Properly blended reformulated gasolines will pro- Ethanol blends are not the responsibility of the manufac- vide excellent performance and durability of engine and turer.
Page 240 STARTING AND OPERATING 239 To fix a Non-FFV vehicle inadvertently fueled once with content of gasoline may not be indicated on the pump, E-85 perform the following: you should ask your gasoline retailer if that gasoline contains MMT. • drain the fuel tank (see your authorized dealer) It is even more important to look for gasolines without •...
Page 241 240 STARTING AND OPERATING Fuel System Cautions CAUTION! (Continued) Follow these guidelines to maintain your vehicle’s per- • The use of fuel additives which are now being formance: sold as octane enhancers is not recommended. Most of these products contain high concentra- CAUTION! tions of methanol.
Page 242: Adding Fuel
STARTING AND OPERATING 241 Carbon Monoxide Warnings WARNING! (Continued) • Guard against carbon monoxide with proper WARNING! maintenance. Have the exhaust system inspected Carbon monoxide (CO) in exhaust gases is deadly. every time the vehicle is raised. Have any abnor- Follow the precautions below to prevent carbon mal conditions repaired promptly.
Page 243: Fuel Filler Cap (Gas Cap)
242 STARTING AND OPERATING Fuel Filler Cap (Gas Cap) CAUTION! (Continued) The gas cap is behind the fuel filler door, on the passen- • A poorly fitting gas cap could let impurities into ger’s side of the vehicle. If the gas cap is lost or damaged, the fuel system.
Page 244: Loose Fuel Filler Cap Message
STARTING AND OPERATING 243 • When the fuel nozzle “clicks” or shuts off, the fuel WARNING! (Continued) tank is full. • Never add fuel when the engine is running. This is Loose Fuel Filler Cap Message in violation of most state and federal fire regula- If the vehicle diagnostic system determines that the fuel tions and doing so will cause the malfunction filler cap is loose, improperly installed, or damaged, a...
Page 245: Vehicle Loading
244 STARTING AND OPERATING VEHICLE LOADING The bar code allows a computer scanner to read the As required by National Highway Traffic Safety Admin- Vehicle Identification Number (VIN). istration regulations, your vehicle has a certification label Gross Vehicle Weight Rating (GVWR) affixed to the driver’s side door or B-Pillar.
Page 246 STARTING AND OPERATING 245 Curb Weight Overloading can cause potential safety hazards and The curb weight of a vehicle is defined as the total weight shorten useful service life. Heavier suspension compo- of the vehicle with all fluids, including vehicle fuel, at full nents do not necessarily increase the vehicle’s GVWR.
Page 247: Trailer Towing
246 STARTING AND OPERATING TRAILER TOWING Gross Trailer Weight (GTW) In this section you will find safety tips and information The GTW is the weight of the trailer plus the weight of all on limits to the type of towing you can reasonably do cargo, consumables and equipment (permanent or tem- with your vehicle.
Page 248 STARTING AND OPERATING 247 Trailer Sway Control WARNING! The trailer sway control is a telescoping link that can be installed between the hitch receiver and the trailer tongue It is important that you do not exceed the maximum that typically provides adjustable friction associated with front or rear GAWR.
Page 249 248 STARTING AND OPERATING Weight-Distributing Hitch WARNING! A weight-distributing hitch system works by applying leverage through spring (load) bars. They are typically An improperly adjusted Weight-Distributing Hitch used for heavier loads, to distribute trailer tongue weight system may reduce handling, stability, braking per- to the tow vehicle’s front axle and the trailer axle(s).
Page 250 STARTING AND OPERATING 249 The following chart provides the industry standard for TRAILER HITCH CLASSIFICATIONS the maximum trailer weight a given trailer hitch class can Max. Class tow and should be used to assist you in selecting the GTW (Gross Trailer Wt.) correct trailer hitch for your intended towing condition.
Page 251 250 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Trailer Towing Weights Max. GTW Max. Tongue Wt. Engine/Transmission Frontal Area (Gross Trailer Wt.) (See Note) 2.4L/Automatic 20 sq ft (1.9 sq m) 1,000 lbs (454 kg)
Page 252 STARTING AND OPERATING 251 • The weight of any other type of cargo or equipment put in or on your vehicle. • The weight of the driver and all passengers. NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle.
Page 253 252 STARTING AND OPERATING CAUTION! WARNING! • Do not tow a trailer at all during the first 500 miles • Improper towing can lead to an injury accident. • Make certain that the load is secured in the trailer (805 km) the new vehicle is driven. The engine, axle or other parts could be damaged.
Page 254 STARTING AND OPERATING 253 frame or hook retainers of the vehicle hitch. Cross the always achieve the 10% to 15% range of trailer tongue chains under the trailer tongue and allow enough weight as a percentage of total trailer weight.) slack for turning corners.
Page 255 254 STARTING AND OPERATING • When replacing tires, refer to “Tires-General Informa- • Trailer brakes are recommended for trailers over tion” in “Starting and Operating” for proper tire 1,000 lbs (454 kg) and required for trailers in excess of replacement procedures. Replacing tires with a higher 2,000 lbs (907 kg).
Page 256 STARTING AND OPERATING 255 Towing Requirements – Trailer Lights and Wiring WARNING! Whenever you pull a trailer, regardless of the trailer size, • Do not connect trailer brakes to your vehicle’s stop lights and turn signals on the trailer are required for motoring safety.
Page 257 256 STARTING AND OPERATING The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following four-pin connector and seven-pin connector illustrations. Seven-Pin Connector 1 — Battery 5 — Ground 2 —...
Page 258: Towing Tips
STARTING AND OPERATING 257 Towing Tips 45 minutes of continuous operation. Refer to “Mainte- Before setting out on a trip, practice turning, stopping nance Schedule” for the proper maintenance intervals. and backing the trailer in an area away from heavy NOTE: Check the automatic transmission fluid level traffic.
Page 259: Recreational Towing (Behind Motorhome, Etc.)
258 STARTING AND OPERATING Cooling System RECREATIONAL TOWING (BEHIND To reduce potential for engine and transmission over- MOTORHOME, ETC.) heating, take the following actions: Automatic Transmission • City Driving CAUTION! When stopped for short periods of time, shift the trans- mission into NEUTRAL but do not increase engine idle Recreational towing on vehicle’s equipped with a speed.
Page 260: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flashers ....260 Jump-Starting ......268 If Your Engine Overheats .
Page 261: Hazard Warning Flashers
260 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel, below the radio. potential for overheating by taking the appropriate ac- tion.
Page 262 WHAT TO DO IN EMERGENCIES 261 • You can also turn the temperature control to maximum CAUTION! heat, the mode control to floor and the blower control to high. This allows the heater core to act as a Driving with a hot cooling system could damage supplement to the radiator and aids in removing heat your vehicle.
Page 263: Jacking And Tire Changing
262 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING Jack Location The jack and jack-handle are stowed behind the right rear WARNING! side trim panel in the cargo area. • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed.
Page 264: Spare Tire Stowage
WHAT TO DO IN EMERGENCIES 263 Spare Tire Stowage Spare Tire Removal The compact spare tire is stowed under the rear of the Lift up the cover and fit the jack-handle over the drive vehicle by means of a hook/basket mechanism. To re- nut.
Page 265: Preparations For Jacking
264 WHAT TO DO IN EMERGENCIES Preparations For Jacking 6. Block both the front and rear of the wheel diagonally opposite the jacking 1. Park the vehicle on a firm, level surface. Avoid ice or position. For example, if changing the slippery areas.
Page 266: Jacking Instructions
WHAT TO DO IN EMERGENCIES 265 Jacking Instructions WARNING! (Continued) • Do not get under the vehicle when it is on a jack. WARNING! • Only use the jack in the positions indicated and Carefully follow these tire changing warnings to help for lifting this vehicle during a tire change.
Page 267 266 WHAT TO DO IN EMERGENCIES 1. Remove the scissors jack and lug wrench from the 2. There are two jacking locations on each side of the stowage bag. body, one at the front of the vehicle and one in the rear on the trailing arm bracket under the triangular cut out NOTE: If equipped with a center cap that covers the symbol.
Page 268 WHAT TO DO IN EMERGENCIES 267 tire just clears the surface and enough clearance is obtained to install the spare tire. Minimum tire lift provides maximum stability. WARNING! Raising the vehicle higher than necessary can make the vehicle less stable. It could slip off the jack and hurt someone near it.
Page 269: Jump-Starting
268 WHAT TO DO IN EMERGENCIES 7. Remove the wheel blocks and lower the jack until it is WARNING! free. Stow the lug wrench, and jack in their designated location. Secure all parts using the means provided. To avoid possible personal injury, handle the wheel covers with care to avoid contact with any sharp WARNING! edges.
Page 270: Preparations For Jump-Start
WHAT TO DO IN EMERGENCIES 269 another vehicle or by using a portable battery booster Preparations for Jump-Start pack. Jump-starting can be dangerous if done improperly The battery in your vehicle is located in the engine so please follow the procedures in this section carefully. compartment just behind the left front headlight assem- bly.
Page 271: Jump-Starting Procedure
270 WHAT TO DO IN EMERGENCIES 3. If using another vehicle to jump-start the battery, park WARNING! the vehicle within the jumper cables reach, set the • Take care to avoid the radiator cooling fan when- parking brake and make sure the ignition is OFF. ever the hood is raised.
Page 272 WHAT TO DO IN EMERGENCIES 271 CAUTION! WARNING! Failure to follow these procedures could result in Do not connect the cable to the negative post (-) of the damage to the charging system of the booster vehicle discharged battery. The resulting electrical spark or the discharged vehicle.
Page 273: Freeing A Stuck Vehicle
272 WHAT TO DO IN EMERGENCIES 8. Disconnect the opposite end of the positive (+) jumper FREEING A STUCK VEHICLE cable from the positive (+) post of the booster battery. NOTE: If your vehicle is equipped with Traction Con- 9. Disconnect the positive (+) end of the jumper cable trol, turn the system OFF before attempting to “rock”...
Page 274: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES 273 TOWING A DISABLED VEHICLE WARNING! Towing With The Key-In-Ignition Fast spinning tires can be dangerous. Forces gener- Four-Speed Automatic Transaxle ated by excessive wheel speeds may cause tire dam- Your vehicle may be towed under the following condi- age or failure.
Page 275: Towing Without The Key-In-Ignition
274 WHAT TO DO IN EMERGENCIES All Transaxles Towing Without The Key-In-Ignition Special care must be taken when the vehicle is towed CAUTION! with the ignition in the LOCK position. A dolly should be used under the front wheels if the rear wheels are raised. If the vehicle being towed requires steering, the Proper towing equipment is necessary to prevent dam- ignition switch must be in the ACC position, not in...
Page 276 MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment — 2.4L ... . 277 Engine Oil Filter ....284 Onboard Diagnostic System —...
Page 277 276 MAINTAINING YOUR VEHICLE Brake System ..... . 298 Front Fog Lamps – If Equipped ..314 Automatic Transmission .
Page 278: Engine Compartment - 2.4L
MAINTAINING YOUR VEHICLE 277 ENGINE COMPARTMENT — 2.4L 1 — Washer Fluid Reservoir 7 — Battery 2 — Power Steering Fluid Reservoir 8 — Automatic Transmission Dipstick 3 — Engine Coolant Reservoir 9 — Engine Oil Dipstick 4 — Brake Fluid Reservoir 10 —...
Page 279: Onboard Diagnostic System - Obd Ii
278 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM — OBD II installed, or damaged. A “gASCAP” message will be Your vehicle is equipped with a sophisticated onboard displayed in the instrument cluster. Tighten the gas cap diagnostic system called OBD II. This system monitors until a clicking sound is heard.
Page 280 MAINTAINING YOUR VEHICLE 279 Indicator Light (MIL)” is functioning and is not on when 3. As soon as you turn the ignition switch to the ON the engine is running, and that the OBD II system is position, you will see the MIL symbol come on as part of ready for testing.
Page 281: Replacement Parts
280 MAINTAINING YOUR VEHICLE you may need to do nothing more than drive your DEALER SERVICE vehicle as you normally would in order for your OBD II Your authorized dealer has the qualified service person- system to update. A recheck with the above test routine nel, special tools, and equipment to perform all service may then indicate that the system is now ready.
Page 282: Maintenance Procedures
Immediately have potential malfunctions Checking Oil Level examined by an authorized Chrysler Group LLC To assure proper engine lubrication, the engine oil must dealership or qualified repair center. be maintained at the correct level. Check the oil level at regular intervals, such as every fuel stop.
Page 283 282 MAINTAINING YOUR VEHICLE The best time to check the engine oil level is about five Change Engine Oil minutes after a fully warmed engine is shut off. Do not Road conditions and your kind of driving affects the check oil level before starting the engine after it has sat interval at which your oil should be changed.
Page 284 • If equipped for and operating with E-85 (ethanol) recommends engine oils that are API certified and meet fuel. the requirements of Chrysler Material Standard MS-6395. NOTE: If ANY of these apply to you, then change your American Petroleum Institute (API) Engine Oil...
Page 285: Engine Oil Filter
284 MAINTAINING YOUR VEHICLE Engine Oil Viscosity (SAE Grade) – 2.4L Engine Materials Added to Engine Oils SAE 5W-20 engine oil is recommended for all operating The manufacturer strongly recommends against the ad- temperatures. This engine oil improves low temperature dition of any additives (other than leak detection dyes) to starting and vehicle fuel economy.
Page 286: Engine Air Cleaner Filter
MAINTAINING YOUR VEHICLE 285 Engine Oil Filter Selection WARNING! This engine has a full-flow type disposable oil filter. Use a filter of this type for replacement. The quality of The air cleaner can provide a measure of protection replacement filters varies considerably. Only high-quality in the case of engine backfire.
Page 287: Maintenance-Free Battery
286 MAINTAINING YOUR VEHICLE Maintenance-Free Battery WARNING! (Continued) Your vehicle is equipped with a maintenance-free battery. • Battery gas is flammable and explosive. Keep You will never have to add water, nor is periodic main- flame or sparks away from the battery. Do not use tenance required.
Page 288: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 287 Air Conditioner Maintenance CAUTION! For best possible performance, your air conditioner • It is essential when replacing the cables on the should be checked and serviced by an authorized dealer at the start of each warm season. This service should battery that the positive cable is attached to the include cleaning of the condenser fins and a performance positive post and the negative cable is attached to...
Page 289: Body Lubrication
288 MAINTAINING YOUR VEHICLE Protection Agency and is an ozone-saving product. How- WARNING! ever, the manufacturer recommends that air conditioning • Use only refrigerants and compressor lubricants service be performed by dealers or other service facilities using recovery and recycling equipment. approved by the manufacturer for your air condi- tioning system.
Page 290: Windshield Wiper Blades
MAINTAINING YOUR VEHICLE 289 hood latching components to ensure proper function. Operation of the wipers on dry glass for long periods When performing other underhood services, the hood may cause deterioration of the wiper blades. Always use latch, release mechanism and safety catch should be washer fluid when using the wipers to remove salt or dirt cleaned and lubricated.
Page 291: Exhaust System
290 MAINTAINING YOUR VEHICLE exhaust system each time the vehicle is raised for an oil WARNING! change or lubrication. Replace as required. Commercially available windshield washer solvents WARNING! are flammable. They could ignite and burn you. Care must be exercised when filling or working around Exhaust gases can injure or kill.
Page 292 MAINTAINING YOUR VEHICLE 291 Under normal operating conditions, the catalytic con- NOTE: Intentional tampering with emissions control verter will not require maintenance. However, it is im- systems can result in civil penalties being assessed portant to keep the engine properly tuned to assure against you.
Page 293: Cooling System
292 MAINTAINING YOUR VEHICLE To minimize the possibility of catalyst damage: WARNING! (Continued) • Do not shut off the engine or interrupt the ignition • You or others can be badly burned by hot engine when the transmission is in gear and the vehicle is in coolant (antifreeze) or steam from your radiator.
Page 294 MAINTAINING YOUR VEHICLE 293 Check the coolant recovery bottle tubing for brittle rub- CAUTION! ber, cracking, tears, cuts and tightness of the connection • Mixing of engine coolant (antifreeze) other than at the bottle and radiator. Inspect the entire system for leaks.
Page 295 294 MAINTAINING YOUR VEHICLE • The manufacturer recommends using MOPAR CAUTION! (Continued) Antifreeze/Coolant 5 Year/100,000 Mile Formula • This vehicle has not been designed for use with HOAT (Hybrid Organic Additive Technology) or Propylene Glycol based engine coolant (anti- equivalent. freeze).
Page 296 MAINTAINING YOUR VEHICLE 295 NOTE: Mixing engine coolant (antifreeze) types will WARNING! decrease the life of the engine coolant (antifreeze) and • The warning words “DO NOT OPEN HOT” on will require more frequent coolant changes. the cooling system pressure cap are a safety pre- Cooling System Pressure Cap caution.
Page 297: Maintaining Your Vehicle
296 MAINTAINING YOUR VEHICLE Disposal of Used Engine Coolant engine idling, and warm to normal operating tempera- Used ethylene glycol-based engine coolant (antifreeze) is ture, the level of the engine coolant (antifreeze) in the a regulated substance requiring proper disposal. Check bottle should be between the ranges indicated on the with your local authorities to determine the disposal bottle.
Page 298 MAINTAINING YOUR VEHICLE 297 • If frequent engine coolant (antifreeze) additions are Points to Remember required, or if the level in the coolant recovery bottle NOTE: When the vehicle is stopped after a few miles (a does not drop when the engine cools, the cooling few kilometers) of operation, you may observe vapor system should be pressure tested for leaks.
Page 299: Brake System
298 MAINTAINING YOUR VEHICLE result in unsatisfactory engine coolant (antifreeze) WARNING! performance, poor gas mileage, and increased • Use only manufacturer’s recommended brake emissions. fluid. Refer to “Fluids, Lubricants, and Genuine Brake System Parts” in “Maintaining Your Vehicle” for further Fluid Level Check –...
Page 300: Automatic Transmission
MAINTAINING YOUR VEHICLE 299 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or • Do not allow petroleum based fluid to contami- moisture, use only new brake fluid or fluid that nate the brake fluid. Brake seal components could has been in a tightly closed container.
Page 301 300 MAINTAINING YOUR VEHICLE Fluid Level Check driven at least 15 miles (24 km). Hot fluid cannot be held Use the following procedure to check the automatic comfortably between the fingertips. Cold fluid is at a transmission fluid level properly: temperature below 80°F (27°C).
Page 302 MAINTAINING YOUR VEHICLE 301 Fluid and Filter Changes CAUTION! Automatic transmission fluid and filter should be • Using a transmission fluid other than the manu- changed as follows: facturer’s recommended fluid may cause deterio- Maintenance Schedule A — No change necessary. ration in transmission shift quality and/or torque Maintenance Schedule B —...
Page 303: Appearance Care And Protection From Corrosion
302 MAINTAINING YOUR VEHICLE policy is the use of special dyes to aid in detecting fluid road surfaces on which the vehicle is operated, extreme leaks. In addition, avoid using transmission sealers as hot or cold weather and other extreme conditions will they may adversely affect seals.
Page 304 MAINTAINING YOUR VEHICLE 303 • Atmospheric fallout/industrial pollutants. CAUTION! Washing • Do not use abrasive or strong cleaning materials • Wash your vehicle regularly. Always wash your ve- such as steel wool or scouring powder, which will hicle in the shade using MOPAR Car Wash or equiva- scratch metal and painted surfaces.
Page 305 304 MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or heavy soil and/or excessive brake dust, use MOPAR similar cause, which destroys the paint and protective Wheel Cleaner or equivalent, or select a nonabrasive, coating, have your vehicle repaired as soon as pos- non-acidic cleaner.
Page 306 MAINTAINING YOUR VEHICLE 305 Stain Repel Fabric Cleaning Procedure – If Interior Care Equipped Use MOPAR Total Clean or equivalent to clean fabric Stain Repel seats may be cleaned in the following man- upholstery and carpeting. ner: Interior trim should be cleaned starting with a damp •...
Page 307 306 MAINTAINING YOUR VEHICLE and should be removed promptly with a damp cloth. Plastic is not as scratch resistant as glass and therefore Stubborn soils can be removed easily with a soft cloth different lens cleaning procedures must be followed. and MOPAR Total Clean or equivalent.
Page 308 MAINTAINING YOUR VEHICLE 307 scratch the elements. When cleaning the rear view mirror, 2. Dry with a soft tissue. spray cleaner on the towel or rag that you are using. Do Seat Belt Maintenance not spray cleaner directly on the mirror. Do not bleach, dye or clean the belts with chemical Instrument Panel Cover solvents or abrasive cleaners.
Page 309: Fuses
308 MAINTAINING YOUR VEHICLE FUSES Cartridge Cavity Mini-Fuse Description Fuse Integrated Power Module (IPM) EMPTY The Integrated Power Module is located in the engine 20 Amp Yellow AWD ECU compartment near the air cleaner assembly. This center Feed — If contains cartridge fuses and mini fuses.
Page 310 MAINTAINING YOUR VEHICLE 309 Cartridge Cartridge Cavity Mini-Fuse Description Cavity Mini-Fuse Description Fuse Fuse 40 Amp Power Seats 10 Amp Red IOD Feed CVT Green Mod/Mod_ 20 Amp Yellow CCN Feed, Power Locks 40 Amp ASD Relay Green Contact Feed 15 Amp Lt Blue Power Outlet 20 Amp Yellow PWR Amp 1 &...
Page 311 310 MAINTAINING YOUR VEHICLE Cartridge Cartridge Cavity Mini-Fuse Description Cavity Mini-Fuse Description Fuse Fuse 25 Amp Natu- PWR Sunroof 30 Amp ENG ASD Con- Feed Pink trol Feed 1 10 Amp Red Heated Mirror 10 Amp Red ABS MOD/ J1962 Conn/ 15 Amp Lt.
Page 312: Vehicle Storage
MAINTAINING YOUR VEHICLE 311 VEHICLE STORAGE CAUTION! If you will not be using your vehicle for more than • When installing the Integrated Power Module 21 days, you may want to take steps to preserve your battery. cover, it is important to ensure the cover is prop- erly positioned and fully latched.
Page 313: Bulb Replacement
312 MAINTAINING YOUR VEHICLE All the interior bulbs are brass or glass wedge base. BULB REPLACEMENT Aluminum base bulbs are not approved and should not Headlamps be used for replacement. CAUTION! LIGHTS BULBS – Exterior Bulb No. Do not touch the new headlamp bulb with your Low Beam Headlamp .
Page 314: Front Parking, Turn Signal, And Side Marker Lamps
MAINTAINING YOUR VEHICLE 313 2. Disconnect the electrical connector. 3. Rotate the socket to the left one-quarter turn, and replace the bulb. 3. Rotate the socket to the left one-quarter turn, and replace the bulb. Front Parking, Turn Signal, and Side Marker Lamps 1.
Page 315: Front Fog Lamps - If Equipped
314 MAINTAINING YOUR VEHICLE Front Fog Lamps – If Equipped 1. Remove the fasteners attaching the lower splash shield to gain access to the fog lamp. 2. Twist and remove the bulb from the fog lamp housing. 3. Disconnect the electrical connector and replace bulb. Rear Tail, Stop and Turn Signal Lamps 1.
Page 316: Backup Lamps
MAINTAINING YOUR VEHICLE 315 Backup Lamps 2. Fully compress the clip to get the lamp to come out completely. 1. To remove the backup lamp, you must take a fiber stick and slide it along the inboard side of the lamp and 3.
Page 317: Fluid Capacities
316 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Metric Fuel (Approximate) 15 Gallons 56.7 Liters Engine Oil with Filter 2.4L Engine (SAE 5W-20, API Certified) 5 Quarts 4.7 Liters Cooling System * 2.4L Engine (MOPAR Antifreeze/Engine Coolant 5 6.5 Quarts 6.2 Liters Year/100,000 Mile Formula or equivalent) * Includes heater and coolant recovery bottle filled to MAX level.
Page 318: Fluids, Lubricants And Genuine Parts
Organic Additive Technology) or equivalent. Engine Oil Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395. Refer to your engine oil filler cap for correct SAE grade. Engine Oil Filter MOPAR Engine Oil Filter or equivalent.
Page 319: Chassis
318 MAINTAINING YOUR VEHICLE Chassis Component Fluid, Lubricant, or Genuine Part Automatic Transmission MOPAR ATF+4 Automatic Transmission Fluid or equivalent licensed ATF+4 product. Brake Master Cylinder MOPAR DOT 3 and SAE J1703 should be used or equivalent. If DOT 3 brake fluid is not available, then DOT 4 is acceptable.
Page 320 MAINTENANCE SCHEDULES CONTENTS Emissions Control System Maintenance ..320 At Each Oil Change ....322 Maintenance Schedules ....320 Maintenance Schedule B .
Page 321: Emissions Control System Maintenance
320 MAINTENANCE SCHEDULES EMISSIONS CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULES The Scheduled Maintenance services listed in bold type There are three maintenance schedules that show re- must be done at the times or mileages specified to ensure quired service for your vehicle. the continued proper functioning of the emissions control First is “Maintenance Schedule B.”...
Page 322: At Each Stop For Fuel
MAINTENANCE SCHEDULES 321 • Taxi, police, or delivery service (commercial ser- Second is “Maintenance Schedule A.” It is for vehicles vice).† that are not operated under any of the conditions listed under “Maintenance Schedule B.” • Off-road or desert operation. Use the schedule that best describes your driving condi- •...
Page 323: At Each Oil Change
322 MAINTENANCE SCHEDULES • Check the windshield washer solvent and add if At Each Oil Change required. • Change the engine oil filter. Once a Month • Inspect the exhaust system. • Check tire pressure and look for unusual wear or •...
Page 324 MAINTENANCE SCHEDULES 323 • If equipped for and operating with E-85 (ethanol) fuel. Change the automatic transmission fluid and filter every 60,000 miles (100 000 km) if the vehicle is usually NOTE: operated under one or more of the conditions marked •...
Page 325 324 MAINTENANCE SCHEDULES Miles 3,000 6,000 9,000 12,000 15,000 18,000 (Kilometers) (5 000) (10 000) (15 000) (20 000) (25 000) (30 000) Change engine oil and engine oil filter, if not replaced at three months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter, replace as necessary.
Page 326 MAINTENANCE SCHEDULES 325 Miles 21,000 24,000 27,000 30,000 33,000 36,000 (Kilometers) (35 000) (40 000) (45 000) (50 000) (55 000) (60 000) Change engine oil and engine oil filter, if not replaced at three months. Rotate tires. Inspect the brake linings. Adjust parking brake on vehicles equipped with four-wheel disc brakes.
Page 327 326 MAINTENANCE SCHEDULES Miles 39,000 42,000 45,000 48,000 51,000 54,000 (Kilometers) (65 000) (70 000) (75 000) (80 000) (85 000) (90 000) Change engine oil and engine oil filter, if not replaced at three months. Rotate tires. Inspect the brake linings. Change the brake fluid.
Page 328 MAINTENANCE SCHEDULES 327 Miles 57,000 60,000 63,000 66,000 69,000 72,000 (Kilometers) (95 000) (100 000) (105 000) (110 000) (115 000) (120 000) Change engine oil and engine oil filter, if not replaced at three months. Rotate tires. Inspect the brake linings. Adjust parking brake on vehicles equipped with four-wheel disc brakes.
Page 329 328 MAINTENANCE SCHEDULES Miles 75,000 78,000 81,000 84,000 87,000 90,000 (Kilometers) (125 000) (130 000) (135 000) (140 000) (145 000) (150 000) Change engine oil and engine oil filter, if not re- placed at three months. Rotate tires. Inspect the brake linings. Adjust parking brake on vehicles equipped with four-wheel disc brakes.
Page 330 MAINTENANCE SCHEDULES 329 Miles 93,000 96,000 99,000 102,000 105,000 (Kilometers) (155 000) (160 000) (165 000) (170 000) (175 000) Change engine oil and engine oil filter, if not re- placed at three months. Rotate tires. Inspect the brake linings. Change the brake fluid if your vehicle is used for trailer towing.
Page 331 330 MAINTENANCE SCHEDULES Miles 108,000 111,000 114,000 117,000 120,000 (Kilometers) (180 000) (185 000) (190 000) (195 000) (200 000) Change engine oil and engine oil filter, if not re- placed at three months. Rotate tires. Inspect the brake linings. Adjust parking brake on vehicles equipped with four-wheel disc brakes.
Page 332 MAINTENANCE SCHEDULES 331 Miles 123,000 126,000 129,000 132,000 135,000 (Kilometers) (205 000) (210 000) (215 000) (220 000) (225 000) Change engine oil and engine oil filter, if not re- placed at three months. Rotate tires. Inspect the brake linings. Inspect the engine air cleaner filter, and replace as necessary.*...
Page 333 332 MAINTENANCE SCHEDULES Miles 138,000 141,000 144,000 147,000 150,000 (Kilometers) (230 000) (235 000) (240 000) (245 000) (250 000) Change engine oil and engine oil filter, if not re - placed at three months. Rotate tires. Inspect the brake linings. Adjust parking brake on vehicles equipped with four-wheel disc brakes.
Page 334: Maintenance Schedule A
MAINTENANCE SCHEDULES 333 Maintenance Schedule A Miles 6,000 12,000 18,000 24,000 30,000 36,000 (Kilometers) (10 000) (20 000) (30 000) (40 000) (50 000) (60 000) [Months] [12] [18] [24] [30] [36] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings.
Page 335 334 MAINTENANCE SCHEDULES Miles 42,000 48,000 54,000 60,000 66,000 (Kilometers) (70 000) (80 000) (90 000) (100 000) (110 000) [Months] [42] [48] [54] [60] [66] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Adjust parking brake on vehicles equipped with four-wheel disc brakes.
Page 336 MAINTENANCE SCHEDULES 335 Miles 72,000 78,000 84,000 90,000 96,000 102,000 (Kilometers) (120 000) (130 000) (140 000) (150 000) (160 000) (170 000) [Months] [72] [78] [84] [90] [96] [102] Change engine oil and engine oil filter. Rotate tires. Inspect the brake linings. Adjust parking brake on vehicles equipped with four-wheel disc brakes.
Page 337 336 MAINTENANCE SCHEDULES Miles 108,000 114,000 120,000 126,000 132,000 138,000 (Kilometers) (180 000) (190 000) (200 000) (210 000) (220 000) (230 000) [Months] [108] [114] [120] [126] [132] [138] Change engine oil and engine oil filter. Rotate tires. Adjust parking brake on vehicles equipped with four-wheel disc brakes.
Page 338 MAINTENANCE SCHEDULES 337 Miles 144,000 150,000 (Kilometers) (240 000) (250 000) [Months] [144] [150] Change engine oil and engine oil filter. Rotate tires. Adjust parking brake on vehicles equipped with four-wheel disc brakes. Replace the spark plugs. Adjust the generator belt tension. Replace the air cleaner filter.* * This maintenance is recommended by the manufacturer WARNING!
Page 340: If You Need Consumer Assistance
If You Need Assistance ....341 Reporting Safety Defects ....344 Chrysler Group LLC Customer Center ..342 In The 50 United States And Washington, D.C.
Page 341 340 IF YOU NEED CONSUMER ASSISTANCE Publication Order Forms ....345 Traction Grades ..... 347 Department Of Transportation Uniform Tire Temperature Grades .
Page 342: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 341 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
Page 343: Chrysler Group Llc Customer Center
• Vehicle delivery date and mileage This is why you should always talk to an authorized dealer’s service manager first. Most matters can be re- Chrysler Group LLC Customer Center solved with this process. P.O. Box 21–8004 • If for some reason you are still not satisfied, talk to the Auburn Hills, MI 48321–8004...
Page 344: Customer Assistance For The Hearing Or Speech Impaired (Tdd/Tty)
IF YOU NEED CONSUMER ASSISTANCE 343 Customer Assistance For The Hearing Or Speech the manufacturer’s service contracts. If you purchased a Impaired (TDD/TTY) manufacturer’s service contract, you will receive Plan To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date.
Page 345: Warranty Information
See the Warranty Information Booklet, located on the has also made a major investment in facilities, tools, and DVD, for the terms and provisions of Chrysler Group training to assure that you are absolutely delighted with LLC warranties applicable to this vehicle and market.
Page 346: In Canada
Customer Service Department imme- need in diagnosing/troubleshooting, problem solving, diately. Canadian customers who wish to report a safety maintaining, servicing, and repairing Chrysler Group defect to the Canadian government should write to: LLC vehicles. A complete working knowledge of the...
Page 347: Quality Grades
346 IF YOU NEED CONSUMER ASSISTANCE vehicle, system, and/or components is written in acquaint you with specific Chrysler Group LLC ve- straightforward language with illustrations, diagrams, hicles. Included are starting, operating, emergency and charts. and maintenance procedures as well as specifications, capabilities and safety tips.
Page 348: Traction Grades
IF YOU NEED CONSUMER ASSISTANCE 347 in each category is shown on the sidewall of the tires on wet pavement, as measured under controlled conditions your vehicle. on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction perfor- All passenger car tires must conform to Federal safety mance.
Page 349 348 IF YOU NEED CONSUMER ASSISTANCE grade C corresponds to a level of performance, which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No. 109. Grades B and A repre- sent higher levels of performance on the laboratory test wheel, than the minimum required by law.
Page 350 INDEX...
Page 351 350 INDEX ABS (Anti-Lock Brake System) ....210 Alarm System (Security Alarm) ....18 Adding Engine Coolant (Antifreeze) .
Page 352 INDEX 351 Special Additives ..... . 301 Bulb Replacement ..... 311,312 Autostick .
Page 353 352 INDEX Check Engine Light Compass Variance ..... . . 156 (Malfunction Indicator Light) ... . . 148,278 Computer, Trip/Travel .
Page 354 INDEX 353 Customer Assistance ..... 341 Driving On Slippery Surfaces ....202 Daytime Running Lights .
Page 355 354 INDEX Coolant (Antifreeze) ....292 Filler Location Fuel ....143,242 Cooling .
Page 356 INDEX 355 Fog Lights ......103,152 Requirements ......237 Folding Front Passenger Seat .
Page 357 356 INDEX Gross Axle Weight Rating ....246 Ignition ....... 12 Gross Vehicle Weight Rating .
Page 358 INDEX 357 Jump Starting ......268 Lights ......77,101 Airbag .
Page 359 358 INDEX Malfunction Indicator (Check Engine) ..148 Locks Map Reading ......105 Child Protection .
Page 360 INDEX 359 Map/Reading Lights ..... 105 Trip ......146,149 Methanol .
Page 361 360 INDEX Overheating, Engine ....143,260 Preparation for Jacking ....264 Owner’s Manual (Operator Manual) .
Page 362 INDEX 361 Rear Wiper/Washer ..... . 134 Safety, Exhaust Gas ..... . . 74 Recreational Towing .
Page 363 362 INDEX Seat Belts (Sedan) ......34 Service Engine Soon Light Seats ....... . . 85 (Malfunction Indicator) .
Page 364 INDEX 363 Engine Fails to Start ....193 Tilt Steering Column ..... 110 Starting and Operating .
Page 365 364 INDEX Quality Grading ..... . . 346 Trailer Towing ......246 Radial .
Page 366 INDEX 365 Transmitter Programming Vehicle Identification Number (VIN) ... . 6 (Remote Keyless Entry) ....23 Vehicle Loading .
Page 367 366 INDEX Windshield Defroster ..... . 75 Wiper, Delay ......108 Windshield Washers .
Page 368 Chrysler Group LLC 10PT44-126-AC Printed in U.S.A. 3rd Edition...

This manual is also suitable for:

Pt cruiser 2010

Chrysler PT Cruiser Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

Maintenance Schedules

If You Need Consumer Assistance

Quick Links

Chapters

Related Manuals for Chrysler PT Cruiser

Summary of Contents for Chrysler PT Cruiser