Asus P5AD2-E Premium User Manual page 48

3 . 3 . 3 . 3 . I D E R A I D c o n n e c t o r s ( 4 0 - 1 p i n P R I _ R A I D 1 [ r e d ] , I D E R A I D c o n n e c t o r s ( 4 0 - 1 p i n P R I _ R A I D 1 [ r e d ] , I D E R A I D c o n n e c t o r s ( 4 0 - 1 p i n P R I _ R A I D 1 [ r e d ] ,
3 . I D E R A I D c o n n e c t o r s ( 4 0 - 1 p i n P R I _ R A I D 1 [ r e d ] , I D E R A I D c o n n e c t o r s ( 4 0 - 1 p i n P R I _ R A I D 1 [ r e d ] ,
S E C _ R A I D 1 [ r e d ] ) S E C _ R A I D 1 [ r e d ] ) S E C _ R A I D 1 [ r e d ] )
S E C _ R A I D 1 [ r e d ] ) S E C _ R A I D 1 [ r e d ] )
These connectors are for Ultra ATA 133/100/66 signal cables. The
IDE RAID connectors support up to four IDE hard disk drives that you
can configure as a disk array through the onboard IDE RAID controller.
Refer to Chapter 5 for details on how to set up RAID configurations.
These connectors are set to I D E
can connect IDE devices to these connectors such as boot/data hard disk
drives or optical drives. If you intend to create an IDE RAID set using these
connectors, set the I T E 8 2 1 2 F C o n t r o l l e r
Mode]. See section "4.4.6 Onboard Devices Configuration" for details.
P5AD2-E PREMIUM RAID connectors
•
•
•
•
2 - 2 6 2 - 2 6
2 - 2 6 2 - 2 6 2 - 2 6
I T E 8 2 1 2 F C o n t r o l l e r I T E 8 2 1 2 F C o n t r o l l e r item in the BIOS to [RAID I T E 8 2 1 2 F C o n t r o l l e r
I T E 8 2 1 2 F C o n t r o l l e r
®
Before creating a RAID set using Ultra ATA hard disks, make sure
that you have connected the Ultra ATA signal cable and installed Ultra
ATA 133/100/66 hard disk drives.
The system automatically assigns the boot sequence of ATAPI
devices connected to the IDE RAID connectors.
The ITE ® 8212F controller supports a maximum of two Ultra ATA
hard disk drives in RAID 1 configuration.
Before creating a RAID 1 set, make sure that you set the hard disk
drives as either Master or Slave device. Refer to the hard disk drive
documentation for details.
I D E I D E M M M M M o d e I D E I D E o d e o d e by default. In I D E o d e o d e
SEC_RAID1
NOTE: Orient the red markings
(usually zigzag) on the IDE
cable to PIN 1.
PRI_RAID1
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
I D E M M M M M o d e I D E I D E I D E o d e, you o d e o d e o d e
PIN 1