Page 34
Speaker Connector Power LED ® Reset SW IDE_LED P4V8X-X ATX Power SMI Lead Switch* Requires an ATX power supply. P4V8X-X System Panel Connector • • • • • • 1-24...
Page 37
A:\>afudos /iP4V8XX.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading file ..done Erasing flash ..done Writing flash ..0x0008CC00 (9%) A:\>afudos /iP4V8XX.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc.
Page 38
A:\>afudos /oMYBIOS03.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading flash ..0x0008CC00 (9%) A:\>afudos /oMYBIOS03.rom AMI Firmware Update Utility - Version 1.10 Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading flash ..
Page 39
User recovery requested. Starting BIOS recovery... Checking for floppy... User recovery requested. Starting BIOS recovery... Checking for floppy... Floppy found! Reading file “P4V8XX.rom”. Completed. Start flashing... Flashed successfully. Rebooting.
Page 40
Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Floppy found! Reading file “P4V8XX.rom”. Completed. Start flashing...
Page 41
Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Bad BIOS checksum. Starting BIOS recovery... Checking for floppy... Floppy not found! Checking for CD-ROM... CD-ROM found. Reading file “P4V8XX.rom”. Completed. Start flashing...
Page 43
Legacy Diskette A [1.44M, 3.5 in] select a field. Use [+] or [-] to Primary IDE Master :[ST320413A] configure system time. Primary IDE Slave :[ASUS CD-S340] Secondary IDE Master :[Not Detected] Secondary IDE Slave :[Not Detected] System Information Select Screen Select Item...
Page 44
Language [English] Use [+] or [-] to Primary IDE Master :[ST320413A] configure system time. Primary IDE Slave :[ASUS CD-S520] Secondary IDE Master :[Not Detected] Secondary IDE Slave :[Not Detected] Third IDE Master :[Not Detected] Fourth IDE Master...
Page 45
Legacy Diskette A [1.44M, 3.5 in] select a field. Use [+] or [-] to Primary IDE Master :[ST320413A] configure system time. Primary IDE Slave :[ASUS CD-S340] Secondary IDE Master :[Not Detected] Secondary IDE Slave :[Not Detected] System Information Select Screen Select Item...
Page 46
Primary IDE Master Select the type Device : Hard Disk of device connected Vendor : ST320413A to the system. Size : 20.0GB LBA Mode : Supported Block Mode : 16 Sectors PIO Mode Async DMA : MultiWord DMA-2 Ultra DMA : Ultra DMA-5 SMART Monitoring: Supported Type...
Page 47
AMI BIOS Version : 08.00.09 Build Date : 07/07/03 Processor Type : Intel(R) Pentium(R) 4 CPU 1500MHz Speed : 1500 MHz Count System Memory Size : 256MB Select Screen Select Item Change Option General Help Save and Exit Exit 2-13...
Page 48
JumperFree Configuration Configure CPU. USB Configuration CPU Configuration Chipset Onboard Devices Configuration PCI PnP Select Screen Select Item Enter Go to Sub-screen General Help Save and Exit Exit Configure System Frequency/Voltage If your system becomes unstable when using an CPU Compatible Mode [Disabled] 800MHz FSB CPU, enable AI Overclock Tuner...
Page 49
USB Configuration Enables USB host controllers. Module Version : 2.22.4-5.3 USB Devices Enabled : None USB 1.1 Ports Configuration [8 USB Ports] USB 2.0 Ports Enable [Enabled] Legacy USB Support [Auto] USB 2.0 Controller Mode [HiSpeed] USB Mass Storage Device Configuration Select Screen Select Item Change Option...
Page 50
USB Mass Storage Device Configuration Number of seconds POST waits for the USB USB Mass Storage Reset Delay [20 Sec] mass storage device after that start unit No USB Mass Storage device detected command. Device #1 Emulation Type [N/A] Device #2 Emulation Type [N/A] Device #3...
Page 51
Configure advanced CPU settings Manufacturer : Intel(R) Brand String : Intel(R) Pentium(R) 4 CPU 1500MHz Frequency : 1500MHz Ratio Status : Locked Ratio Actual Value : 18 Select Screen Select Item Change Option General Help Save and Exit Exit NorthBridge VIA P4X533 Configuration SouthBridge VIA VT8237 Configuration Select Screen Select Item...
Page 52
******** DRAM Timing ******** Configure SDRAM Timing by SPD [Enabled] SDRAM Frequency [Auto] SDRAM Burst Length [4QW] SDRAM Command Rate [2T] Primary Graphics Adapter [AGP] V-Link 8X Supported [Enabled] AGP Mode Auto Graphics Aperture Size [64MB] Select Screen Select Item Change Option General Help Save and Exit...
Page 53
MPS Revision [1.1] PCI Delay Transaction [Disabled] OnBoard LAN [Enabled] OnBoard LAN Boot ROM [Disabled] OnBoard AC’97 Audio [Enabled] Select Screen Select Item Change Option General Help Save and Exit Exit 2-19...
Page 54
Serial Port1 Address [3F8/IRQ4] Parallel Port Address [378] Parallel Port Mode [ECP] ECP Mode DMA Channel [DMA3] Parallel Port IRQ [IRQ7] Onboard Game/MIDI Port [Disabled] Select Screen Select Item Change Option General Help Save and Exit Exit 2-20...
Page 55
Advanced PCI/PnP settings NO: Lets the bIOS configure all the WARNING: Setting wrong values in the sections below devices in the system. may cause system to malfunction. YES: Lets the Plug and Play OS [No] operating system PCI Latency Timer [64] configure Plug and Allocate IRQ to PCI VGA...
Page 56
Suspend Mode [S1 (POS) only] Configure CPU. Repost Video on S3 Resume [No] ACPI 2.0 Support [No] ACPI APIC Support [Enabled] APM Configuration Hardware Monitor Select Screen Select Item Enter Go to Sub-screen General Help Save and Exit Exit 2-22...
Page 57
Power Management/APM [Enabled] Enabled or disable APM. Video Power Down Mode [Suspend] Hard Disk Power Down Mode [Suspend] Suspend Time Out [Disabled] Power Button Mode [On/Off] Restore on AC Power Loss [Last State] Wake Up/Power On by Ring [Disabled] Power On by Onboard LAN [Disabled] Power On by PCI Device [Disabled]...
Page 59
Hardware Monitor CPU temperature CPU Temperature [21°C/69.5°F] MB Temperature [37°C/98.5°F] CPU Fan Speed [3479RPM] Chassis Fan Speed [N/A] CPU Reference Voltage [1.792V] 3.3V Voltage [3.392V] 5V Voltage [5.134V] 12V Voltage [11.840V] Select Screen Select Item Change Option General Help Save and Exit Exit 2-25...
Page 60
Boot Settings Specifies the Boot Device Priority Boot Device Priority sequence. Boot Settings Configuration Security Select Screen Select Item Enter Go to Sub-screen General Help Save and Exit Exit Boot Device Priority Specifies the boot sequence from the 1st Boot Device [First Floppy Drive] available devices.
Page 61
Boot Settings Configuration Allows BIOS to skip certain tests while Quick Boot [Enabled] booting. This will Full Screen Logo [Enabled] decrease the time Add On ROM Display Mode [Force BIOS] needed to boot the Bootup Num-Lock [On] system. PS/2 Mouse Support [Auto] Wait for ‘F1’...
Page 62
Security Settings <Enter> to change password. Supervisor Password Installed <Enter> again to User Password Not Installed disable password. Change Supervisor Password User Access Level [Full Access] Change User Password Clear User Password Password Check [Setup] Boot Sector Virus Protection [Disabled] Select Screen Select Item Change Option...
Page 64
Exit Options Exit system setup after saving the Exit & Save Changes changes. Exit & Discard Changes Discard Changes F10 key can be used for this operation. Load Setup Defaults Select Screen Select Item Enter Go to Sub-screen General Help Save and Exit Exit 2-30...
Page 70
VIA Tech. RAID BIOS Ver 1.XX Create a RAID array with Create Array the hard disk attached to Delete Array VIA IDE controller Create/Delete Spare Select Boot Array : View Array/Disk Status Serial Number View : Move to next item Enter: Confirme the selection : Exit Channel...
Page 71
VIA Tech. RAID BIOS Ver 1.xx Create a RAID array with Auto Setup For Data Security the hard disk attached to Array Mode RAID 1 (Mirroring) VIA IDE controller Select Disk Drives Start Create Process : View Array/Disk Status : Move to next item Enter: Confirm the selection : Exit Channel...
Page 72
The data on the selected disks will be destroyed. Continue? Press Y/N RAID 0 for performance RAID 1 for data protection RAID 0/1 RAID SPAN for capacity Create only Create and duplicate...
Page 73
The data on the selected disks will be destroyed. Continue? Press Y/N The selected drives will be destroyed. Are you sure? Continue? Press Y/N...
Page 74
: Exit Channel Drive Name Array Name Mode Size(GB) Status Serial_Ch0 Master XXXXXXXXXX xxxxx xxx.xx Serial_Ch1 Master XXXXXXXXXX xxxxx xxx.xx VIA Tech. RAID BIOS Ver 1.xx Create a RAID array with Create Array the hard disk attached to Delete Array VIA IDE controller Create/Delete Spare Select Boot Array...