Micr Error Messages - IBM 1352 - InfoPrint B/W Laser Printer User Manual

Error Message
on Display
Can't Purge Pswd not
enabled
Can't Sort Insufficient
Memory
Command Decode Error
Convert to Esc Error
Flash Full Purge and
Format
Load MICR Toner
Macro Definition Error
Macro Definition Error
Macro Definition Error
Macro Definition Error
Macro Definition Error
Macro Transfer Error
Macro Transfer Error
MICR Definition Error
MICR Password Error
MICR Password Error
MICR Password Error
Security Lock Error
Security Lock Error
Secure MICR Printer User's Guide
July 2003
Printed Message
This error indicates that MICR mode has not
been enabled.
This error indicates the printer does not
have sufficient memory to sort the Audit
Report.
Decode error &%Sx
A syntax error was detected in a MICR
(where x is the
command.
incorrect character)
Invalid Convert to
An error was detected in the User
Escape Character
Programmable Escape Character Selection
Command. The software tried to specify a
NULL or an ampersand as the first Escape
Character.
This error message indicates that the
printer's flash memory is full. The audit trail
cannot accept more jobs until more space
is available in flash.
Before printing a MICR font, the printer
checks for MICR toner. If regular toner is
present, the printer will stop all printing and
display this message.
Invalid decode mode
The Load Flash Resource Command
specified
contained an invalid character specifying
the format of the file. Must be either a D or
S.
Macro ID already in
The resource number in the Load Flash
use on SIMM. Print
Resource Command (&%STL...) was over
menus to see a list
the 32767 list.
of used ID's.
Macro size exceeds
Flash resource file size specified in the
available space
Load Flash Resource Command is too large
fro the available space remaining in the
flash module.
Non-hexadecimal
The Load Flash Resource Command
value received.
contained a non-hexadecimal value in the
byte count parameter.
Non integer value
The resource number in the Load Flash
received.
Resource Command (&%STL...) was not
five integers.
Integer string
The Flash Resource Number in the Secure
incorrect length
Flash Resource Unlock Command was not
five digits in length.
Non-integer value
The Secure Flash Resource Unlock
received.
Command contained a non-integer value.
The number of digits in the MICR definition
Command is not equal to four, or there is a
non-hexadecimal character in the count.
Password Length
Password length is not equal to eight
Error.
characters.
Password Match
Password sent does not match the current
Error
stored password.
Security Lock Not
Front panel combination feature has been
Enabled Error.
enabled but was not entered before a MICR
job was started.
Integer string
An error was detected in the Activate/Set
incorrect length.
Front Panel Combination Lock Command.
The combination must be eight digits in
length.
Non-integer value
An error was detected in the Activate/Set
received.
Front Panel Combination Lock Command. A
character was received in the command
that was a non-integer.
Description
Page 46
Action
Press Go. Enter MICR mode, then
re-attempt the purge.
Press Go. The printer may need
to be upgraded with more RAM
memory to sort; otherwise an
unsorted Audit Report may be
printed.
Check your software for a
syntax error in the MICR
command that was being used
when the error occurred.
Check the Command (&%STY...)
for errors.
Press Go then purge the audit
trail. Then either defragment or
format flash memory (Utilities
Menu).
Replace standard toner cartridge
with a MICR Toner. Go to
proceed. If MICR toner is not
available, you must power-off
your printer and restart the print
job at a later time when MICR
toner is available.
Check the Command (&%STL...)
for syntax errors.
Check the Load Flash Resource
Command for syntax/numbering
errors.
Format flash memory to remove
all existing resources or upgrade
flash memory to a larger module.
Check the Command (&%STL...)
syntax for errors.
Check the command for syntax/
numbering errors.
Check the Command (&%STP...)
for syntax/numbering errors.
Check the Command (&%STP...)
for syntax/numbering errors.
Check your software for errors in
the MICR definition Command.
Check the Password Command in
your software, it must be eight
characters long.
Check the Password Command in
your software.
From the front panel select MICR
Menu>Security Lock and enter
the correct combination. Press
Go to resume the print job.
Check the Activate/Set Front
Panel Combination Lock Command
in your software.
Check the Activate/Set Front
Panel Combination Lock Command
syntax in your software.
©
Source Technologies
All rights reserved