Advertisement
ELECTRICAL CONNECTION
This appliance must be installed by a qualified person in
accordance with the
latest IEE
with the
manufacturer's
instructions.
Check
that the voltage is the same as that stated on the rating plate.
The rating plate
is located
on the back cover.
WARNING! THIS APPLIANCE MUST BE EARTHED
If an fixed appliance is not equipped with supply cable and plug, the
power supply must be fitted with a disconnect switch in which the
distance between contacts permits total disconnection in accordance
with overvoltage category III, as required by installation regulations.
We recommend that the cooker circuit is rated to 13 amps.
Cable type HO5 RRF 3 X 1.5 mm
Connecting the mains cable
Open the mains terminal block cover as shown, unscrew screw "A"
the cable
clamp,
and
loosen
"L N E" which secure the three
wires of the mains cable. Fit the
cable and refit screw
"A",
the cable
clamp.
Allow sufficient cable length for the
cooker to be pulled out for cleaning,
but do not let it hang
lower
50mm (2")
from
the floor. The cable
can be looped if necessary, but
make sure that it is not kinked or
trapped when the cooker is in
position.
IMPORTANT
The wires in the mains
cable
GREEN AND YELLOW........EARTH
BLUE....................................NEUTRAL
BROWN ...............................LIVE
REPLACING
OF THE CABLE
If
the cable
becomes
damaged
following instructions:
- open the box of the supply board as
- unscrew screw "A"
that secures
- replace the cable with one of the same
to
the features described
in
shut
the gas tap;
-
connect
the 'green-yellow" earth wire to the terminal "
it approximately
10 mm longer
-
connect
the "blue" neutral wire
-
connect
the live wire
to the terminal marked
GAS ADJUSTMENT
Always isolate the cooker from the electricity supply,
supply temporarily and proceed as follows.
- change the injectors,
- adjust the minimum flow of the burners.
REPLACEMENT OF
COOKTOP
To change
the
cooktop
injectors,
grids, remove burners and flame-spreaders (see fig.A), change the
injector (see fig.B) and replace it with another one suitable for the
new type of gas (see table D). Re-assemble everything in
order,
ensuring you position
the flame-spreader correctly.
A
Regulations and in compliance
2
the screws in the mains terminal block
than
are coloured
as
follows:
or
worn, replace it,
observing
shown in
the
diagram
the cable;
length
and
which corresponds
the table; switch the appliance off, and
than
the live wire;
to the terminal marked
"N";
"L".
shut
off the gas
INJECTORS
proceed
as follows: remove the
B
GB
TAB. D
Values referred to Hs - 15°C - 1013,25mbar
Cat. II 2H3+
Kind of gas mbar Nozzle
NATURAL
G 20
BUTANE
28-30
G 30
PROPANE
G 31
MINIMUM FLOW ADJUSTMENT FOR COOKTOP TAPS
To adjust the minimum,
turn the knob towards the minimum flow position . Remove the knob
from the tap, introduce a
Attention: in taps with security valve, the minimum
"Z" is placed outside the
Loosen
the
adjustment
it to decrease the flow.
The proper adjustment is obtained when the flame is
3 or 4 mm
in
For butane/propane gas, the
down.
Make sure that the flame does not go out
the
the max. flow
Assemble the knob again.
below;
WARNINGS
Isolate the cooker from the electricity supply before attempting to
replace the oven lamp.
", leaving
The oven lamp is of a special type
temperatures. To replace it,
glass (A) and replace the
Re-fit
the
protective
reverse
DISMANTLING THE COOKTOP
If it
becomes
proceed
as follows: remove the glass lid from its position
off upwards.
Remove the grids,
unscrew the visible screws "V"
Dismantle the cooktop
15 ).
7
TABELLA GENERALE INIETTORI
Burners
Power KW
N°
max.
115
Rapide
3,00
20
97
Semi rapide 1,75
72
1,00
Auxiliary
128
Triple crown 3,30
85
Rapide
3,00
65
Semi rapide 1,75
50
1,00
Auxiliary
37
93
Triple crown 3,30
proceed
as follows: switch the burner on, and
small
screwdriver in
tap
rod (fig. 12).
Fig. 11
screw in order to increase the flow or
length.
adjustment
screw must be
to the minimum flow
.
APPLIANCE MAINTENANCE
designed to
proceed
as follows:
burnt-out bulb
with one of the same type.
glass.
E 14
25 W - 230 V~
T300°C
A
necessary to repair or replace
the
burners and flame-spreaders (see fig. 13),
located
on the
by unscrewing the 4 rear screws "A" (see fig.
Consum
N°
min. max.
min.
By pass
0,75 286 l/h
72 l/h reg.
0,48 167 l/h
46 l/h reg.
0,33
95 l/h
31 l/h reg.
1,30
315 l/h 124 l/h reg.
0,75 219 g/h
55 g/h 42
0,48 128 g/h
35 g/h 31
0,33
73 g/h
24 g/h 27
1,30 241 g/h
95 g/h 60
to
the tap rod (fig. 11).
adjustment
screw
Z
Fig. 12
tighten
approximately
fully
screwed
when
passing quickly from
withstand high
remove
the
protective
internal
components,
by sliding
cooktop
(see fig. 14).
Advertisement
